Total
18782 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2026-53170 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 8.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: accel/ethosu: reject DMA commands with uninitialized length cmd_state_init() initializes the command state with memset(0xff), leaving dma->len at U64_MAX to signal missing setup. The only setter is NPU_SET_DMA0_LEN; if userspace omits this command and issues NPU_OP_DMA_START, dma->len remains U64_MAX. In dma_length(), a positive stride added to U64_MAX wraps to a small value. With size0 == 1, check_mul_overflow() does not trigger and dma_length() returns 0 instead of U64_MAX. The caller's U64_MAX check then passes, region_size[] stays 0, and the bounds check in ethosu_job.c is bypassed, allowing hardware to execute DMA with stale physical addresses. Fix by checking for U64_MAX at the start of dma_length() before any arithmetic, consistent with the sentinel value used throughout the driver to detect uninitialized fields. | |||||
| CVE-2026-53171 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 8.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: accel/ethosu: fix arithmetic issues in dma_length() dma_length() derives DMA region usage from command stream values and updates region_size[]: len = ((len + stride[0]) * size0 + stride[1]) * size1 region_size[region] = max(..., len + dma->offset) Several arithmetic issues can corrupt the derived region size: - signed stride values may underflow when added to len - intermediate multiplications may overflow - len + dma->offset may overflow during region_size updates - dma_length() error returns were not validated by the caller region_size[] is later used by ethosu_job.c to validate command stream accesses against GEM buffer sizes. Arithmetic wraparound can therefore under-report region usage and bypass the bounds validation. Fix by validating signed additions, using overflow helpers for multiplications and offset updates, and propagating dma_length() failures to the caller. | |||||
| CVE-2026-53172 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: accel/ethosu: fix IFM region index out-of-bounds in command stream parser NPU_SET_IFM_REGION extracts the region index with param & 0x7f, giving a maximum value of 127. However region_size[] and output_region[] in struct ethosu_validated_cmdstream_info are both sized to NPU_BASEP_REGION_MAX (8), giving valid indices [0..7]. Every other region assignment in the same switch uses param & 0x7: NPU_SET_OFM_REGION: st.ofm.region = param & 0x7; NPU_SET_IFM2_REGION: st.ifm2.region = param & 0x7; NPU_SET_WEIGHT_REGION: st.weight[0].region = param & 0x7; NPU_SET_SCALE_REGION: st.scale[0].region = param & 0x7; The 0x7f mask on IFM is inconsistent and appears to be a typo. feat_matrix_length() and calc_sizes() use the region index directly as an array subscript into the kzalloc'd info struct: info->region_size[fm->region] = max(...); A userspace caller supplying NPU_SET_IFM_REGION with param > 7 causes a write up to 127*8 = 1016 bytes past the start of region_size[], corrupting adjacent kernel heap data. Fix by applying the same & 0x7 mask used by all other region assignments. | |||||
| CVE-2026-53173 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: accel/ethosu: fix OOB write in ethosu_gem_cmdstream_copy_and_validate() The command stream parsing loop increments the index variable a second time when a 64-bit command word is encountered (bit 14 set), but does not re-check the loop bound before writing the second word: for (i = 0; i < size / 4; i++) { bocmds[i] = cmds[0]; if (cmd & 0x4000) { i++; bocmds[i] = cmds[1]; /* unchecked */ } } The buffer bocmds is backed by a DMA allocation of exactly size bytes from drm_gem_dma_create(ddev, size), giving valid indices [0, size/4-1]. When i == size/4 - 1 on entry to an iteration and bit 14 of cmds[0] is set, bocmds[size/4-1] is written in bounds, i is then incremented to size/4, and bocmds[size/4] writes four bytes past the end of the allocation. Userspace controls both the buffer contents and the size argument via the ioctl, making this a userspace-triggerable heap out-of-bounds write. Fix by checking the incremented index against the buffer bound before the second write and returning -EINVAL if the buffer is too small to contain the extended command. | |||||
| CVE-2026-53177 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: bnxt_en: Fix NULL pointer dereference PCIe errors detected by a Root Port or Downstream Port cause error recovery services to run on all subordinate devices regardless of administrative state. The .error_detected() callback, bnxt_io_error_detected(), disables and synchronizes IRQs via bnxt_disable_int_sync(), which calls bnxt_cp_num_to_irq_num() to map completion rings to IRQs using bp->bnapi. Since bp->bnapi is allocated on NIC open and freed on NIC close, PCIe error recovery on a closed NIC can dereference a NULL pointer. Check if bp->bnapi is NULL before disabling and synchronizing IRQs. | |||||
| CVE-2026-53179 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix buffer over-read in rtw_update_protection rtw_update_protection() is called with a pointer offset into the ies buffer but the full ie_length is passed, causing a potential buffer over-read. | |||||
| CVE-2026-53149 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: thunderbolt: Bound root directory content to block size __tb_property_parse_dir() does not check that content_offset + content_len fits within block_len for the root directory case. When rootdir->length equals or exceeds block_len - 2, the entry loop reads past the allocated property block. Add a bounds check after computing content_offset and content_len to reject directories whose content extends past the block. | |||||
| CVE-2026-53150 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: thunderbolt: Reject zero-length property entries in validator tb_property_entry_valid() accepts entries with length == 0 for DIRECTORY, DATA, and TEXT types. A zero-length TEXT entry passes validation but causes an underflow in the null-termination logic: property->value.text[property->length * 4 - 1] = '\0'; When property->length is 0 this writes to offset -1 relative to the allocation. Reject zero-length entries early in the validator since they have no valid representation in the XDomain property protocol. | |||||
| CVE-2026-53151 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 9.8 CRITICAL |
| In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix the ACK parser to extract the SACK table for parsing Fix modification of the received skbuff in rxrpc_input_soft_acks() and a potential incorrect access of the buffer in a fragmented UDP packet (the packet would probably have to be deliberately pre-generated as fragmented) when AF_RXRPC tries to extract the contents of the SACK table by copying out the contents of the SACK table into a buffer before attempting to parse AF_RXRPC assumes that it can just call skb_condense() and then validly access the SACK table from skb->data and that it will be a flat buffer - but skb_condense() can silently fail to do anything under some circumstances. Note that whilst rxrpc_input_soft_acks() should be able to parse extended ACKs, the rest of AF_RXRPC doesn't currently support that. Further, there's then no need to call skb_condense() in rxrpc_input_ack(), so don't. | |||||
| CVE-2026-53152 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: mmc: dw_mmc-rockchip: Add missing private data for very old controllers The really old controllers (rk2928, rk3066, rk3188) do not support UHS speeds at all, and thus never handled phase data. For that reason it never had a parse_dt callback and no driver private data at all. Commit ff6f0286c896 ("mmc: dw_mmc-rockchip: Add memory clock auto-gating support") makes the private data sort of mandatory, because the init function checks whether phases are configured internally or through the clock controller. This results in the old SoCs then experiencing NULL-pointer dereferences when they try to access that private-data struct. While we could have if (priv) conditionals in all places, it's way less cluttery to just give the old types their private-data struct. | |||||
| CVE-2026-53162 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: memcg: use round-robin victim selection in refill_stock Harry Yoo reported that get_random_u32_below() is not safe to call in the nmi context and memcg charge draining can happen in nmi context. More specifically get_random_u32_below() is neither reentrant- nor NMI-safe: it acquires a per-cpu local_lock via local_lock_irqsave() on the batched_entropy_u32 state. An NMI that lands on a CPU mid-update of the ChaCha batch state and recurses into the random subsystem would corrupt that state. The memcg_stock local_trylock prevents re-entry on the percpu stock itself, but cannot protect an unrelated subsystem's per-cpu lock. Replace the random pick with a per-cpu round-robin counter stored in memcg_stock_pcp and serialized by the same local_trylock that already guards cached[] and nr_pages[]. No atomics, no random calls, no extra locks needed. | |||||
| CVE-2026-53161 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: fix use-after-free of fastrpc_user in workqueue context There is a race between fastrpc_device_release() and the workqueue that processes DSP responses. When the user closes the file descriptor, fastrpc_device_release() frees the fastrpc_user structure. Concurrently, an in-flight DSP invocation can complete and fastrpc_rpmsg_callback() schedules context cleanup via schedule_work(&ctx->put_work). If the workqueue runs fastrpc_context_free() in parallel with or after fastrpc_device_release() has freed the user structure, it dereferences the freed fastrpc_user. Depending on the state of the context at the time of the race, any one of the following accesses can be hit: 1. fastrpc_buf_free() calls fastrpc_ipa_to_dma_addr(buf->fl->cctx, ...) to strip the SID bits from the stored IOVA before passing the physical address to dma_free_coherent(). 2. fastrpc_free_map() reads map->fl->cctx->vmperms[0].vmid to reconstruct the source permission bitmask needed for the qcom_scm_assign_mem() call that returns memory from the DSP VM back to HLOS. 3. fastrpc_free_map() acquires map->fl->lock to safely remove the map node from the fl->maps list. The resulting use-after-free manifests as: pc : fastrpc_buf_free+0x38/0x80 [fastrpc] lr : fastrpc_context_free+0xa8/0x1b0 [fastrpc] fastrpc_context_free+0xa8/0x1b0 [fastrpc] fastrpc_context_put_wq+0x78/0xa0 [fastrpc] process_one_work+0x180/0x450 worker_thread+0x26c/0x388 Add kref-based reference counting to fastrpc_user. Have each invoke context take a reference on the user at allocation time and release it when the context is freed. Release the initial reference in fastrpc_device_release() at file close. Move the teardown of the user structure — freeing pending contexts, maps, mmaps, and the channel context reference — into the kref release callback fastrpc_user_free(), so that it runs only when the last reference is dropped, regardless of whether that happens at device close or after the final in-flight context completes. | |||||
| CVE-2026-53160 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: fix use-after-free race in fastrpc_map_create fastrpc_map_lookup returns a raw pointer after releasing fl->lock. The caller fastrpc_map_create then calls fastrpc_map_get (kref_get_unless_zero) on this unprotected pointer. A concurrent MEM_UNMAP can free the map between the lock release and the kref operation, resulting in a use-after-free on the freed slab object. Restore the take_ref parameter to fastrpc_map_lookup so the reference is acquired atomically under fl->lock before the pointer is exposed to the caller. | |||||
| CVE-2026-53156 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: nvmem: core: fix use-after-free bugs in error paths Fix several instances of error paths in which we call __nvmem_device_put() - which may end up freeing the underlying memory and other resources - and then keep on using the nvmem structure. Always put the reference to the nvmem device as the last step before returning the error code. | |||||
| CVE-2026-53128 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drbd: Balance RCU calls in drbd_adm_dump_devices() Make drbd_adm_dump_devices() call rcu_read_lock() before rcu_read_unlock() is called. This has been detected by the Clang thread-safety analyzer. | |||||
| CVE-2026-53129 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: fs/mbcache: cancel shrink work before destroying the cache mb_cache_destroy() calls shrinker_free() and then frees all cache entries and the cache itself, but it does not cancel the pending c_shrink_work work item first. If mb_cache_entry_create() schedules c_shrink_work via schedule_work() and the work item is still pending or running when mb_cache_destroy() runs, mb_cache_shrink_worker() will access the cache after its memory has been freed, causing a use-after-free. This is only reachable by a privileged user (root or CAP_SYS_ADMIN) who can trigger the last put of a mounted ext2/ext4/ocfs2 filesystem. Cancel the work item with cancel_work_sync() before calling shrinker_free(), ensuring the worker has finished and will not be rescheduled before the cache is torn down. | |||||
| CVE-2026-53130 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: fs/omfs: reject s_sys_blocksize smaller than OMFS_DIR_START omfs_fill_super() rejects oversized s_sys_blocksize values (> PAGE_SIZE), but it does not reject values smaller than OMFS_DIR_START (0x1b8 = 440). Later, omfs_make_empty() uses sbi->s_sys_blocksize - OMFS_DIR_START as the length argument to memset(). Since s_sys_blocksize is u32, a crafted filesystem image with s_sys_blocksize < OMFS_DIR_START causes an unsigned underflow there, wrapping to a value near 2^32. That drives a ~4 GiB memset() from bh->b_data + OMFS_DIR_START and overwrites kernel memory far beyond the backing block buffer. Add the corresponding lower-bound check alongside the existing upper-bound check in omfs_fill_super(), so that malformed images are rejected during superblock validation before any filesystem data is processed. | |||||
| CVE-2026-53131 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 9.4 CRITICAL |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: require Ethernet MAC header before using eth_hdr() `ip6t_eui64`, `xt_mac`, the `bitmap:ip,mac`, `hash:ip,mac`, and `hash:mac` ipset types, and `nf_log_syslog` access `eth_hdr(skb)` after either assuming that the skb is associated with an Ethernet device or checking only that the `ETH_HLEN` bytes at `skb_mac_header(skb)` lie between `skb->head` and `skb->data`. Make these paths first verify that the skb is associated with an Ethernet device, that the MAC header was set, and that it spans at least a full Ethernet header before accessing `eth_hdr(skb)`. | |||||
| CVE-2026-53132 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: vsock/virtio: fix potential unbounded skb queue virtio_transport_inc_rx_pkt() checks vvs->rx_bytes + len > vvs->buf_alloc. virtio_transport_recv_enqueue() skips coalescing for packets with VIRTIO_VSOCK_SEQ_EOM. If fed with packets with len == 0 and VIRTIO_VSOCK_SEQ_EOM, a very large number of packets can be queued because vvs->rx_bytes stays at 0. Fix this by estimating the skb metadata size: (Number of skbs in the queue) * SKB_TRUESIZE(0) | |||||
| CVE-2026-53139 | 1 Linux | 1 Linux Kernel | 2026-07-06 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Skip CSD when it has zeroed workgroups A compute shader dispatch encodes its workgroup counts in the CFG0..CFG2 registers. Kicking off a dispatch with a zero count in any of the three dimensions is invalid. First, the hardware will process 0 as 65536, while the user-space driver exposes a maximum of 65535. Over that, a submission with a zeroed workgroup dimension should be a no-op. These zeroed counts can reach the dispatch path through an indirect CSD job, whose workgroup counts are only known once the indirect buffer is read and may legitimately be zero, but such scenario should only result in a no-op. Overwrite the indirect CSD job workgroup counts with the indirect BO ones, even if they are zeroed, and don't submit the job to the hardware when any of the workgroup counts is zero, so the job completes immediately instead of running the shader. | |||||