Export limit exceeded: 11476 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (11476 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-53147 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 8.1 High |
| In the Linux kernel, the following vulnerability has been resolved: thunderbolt: Validate XDomain request packet size before type cast tb_xdp_handle_request() casts the received packet buffer to protocol-specific structs without verifying that the allocation is large enough for the target type. A peer can send a minimal XDomain packet that passes the generic header length check but is shorter than the struct accessed after the cast, causing out-of- bounds reads from the kmemdup allocation. Plumb the packet length through xdomain_request_work and validate it against the expected struct size before each cast. | ||||
| CVE-2026-52917 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: sctp: diag: reject stale associations in dump_one path The SCTP exact sock_diag lookup can hold a transport reference, block on lock_sock(sk), and then resume after sctp_association_free() has marked the association dead and freed its bind address list. When that happens, inet_assoc_attr_size() and inet_diag_msg_sctpasoc_fill() can still dereference association state that is no longer valid for reporting. In particular, inet_diag_msg_sctpasoc_fill() may read an empty bind-address list as a real sctp_sockaddr_entry and trigger an out-of-bounds read from unrelated association memory. Reject the association after taking the socket lock if it has been reaped or detached from the endpoint, and report the lookup as stale. This keeps the exact dump-one path from formatting torn association state. | ||||
| CVE-2026-46307 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 8.3 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath5k: do not access array OOB Vincent reports: > The ath5k driver seems to do an array-index-out-of-bounds access as > shown by the UBSAN kernel message: > UBSAN: array-index-out-of-bounds in drivers/net/wireless/ath/ath5k/base.c:1741:20 > index 4 is out of range for type 'ieee80211_tx_rate [4]' > ... > Call Trace: > <TASK> > dump_stack_lvl+0x5d/0x80 > ubsan_epilogue+0x5/0x2b > __ubsan_handle_out_of_bounds.cold+0x46/0x4b > ath5k_tasklet_tx+0x4e0/0x560 [ath5k] > tasklet_action_common+0xb5/0x1c0 It is real. 'ts->ts_final_idx' can be 3 on 5212, so: info->status.rates[ts->ts_final_idx + 1].idx = -1; with the array defined as: struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES]; while the size is: #define IEEE80211_TX_MAX_RATES 4 is indeed bogus. Set this 'idx = -1' sentinel only if the array index is less than the array size. As mac80211 will not look at rates beyond the size (IEEE80211_TX_MAX_RATES). Note: The effect of the OOB write is negligible. It just overwrites the next member of info->status, i.e. ack_signal. | ||||
| CVE-2026-46303 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 8.2 High |
| In the Linux kernel, the following vulnerability has been resolved: isofs: validate Rock Ridge CE continuation extent against volume size rock_continue() reads rs->cont_extent verbatim from the Rock Ridge CE record and passes it to sb_bread() without checking that the block number is within the mounted ISO 9660 volume. commit e595447e177b ("[PATCH] rock.c: handle corrupted directories") added cont_offset and cont_size rejection for the CE continuation but did not validate the extent block number itself. commit f54e18f1b831 ("isofs: Fix infinite looping over CE entries") later capped the CE chain length at RR_MAX_CE_ENTRIES = 32 but again left the block number unchecked. With a crafted ISO mounted via udisks2 (desktop optical auto-mount) or via CAP_SYS_ADMIN mount, rs->cont_extent can therefore point at an out-of-range block or at blocks belonging to an adjacent filesystem on the same block device. sb_bread() on an out-of-range block returns NULL cleanly via the block layer EIO path, so there is no memory-safety violation. For in-range reads of adjacent- filesystem data, the CE buffer is parsed as Rock Ridge records and only the text of SL sub-records reaches userspace through readlink(), which makes the info-leak channel narrow and difficult to exploit; still, rejecting the malformed CE outright matches the rejection shape already present in the same function for cont_offset and cont_size. Add an ISOFS_SB(sb)->s_nzones bounds check to rock_continue() next to the existing offset/size rejection, printing the same corrupted-directory-entry notice. | ||||
| CVE-2026-46191 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: fbcon: Avoid OOB font access if console rotation fails Clear the font buffer if the reallocation during console rotation fails in fbcon_rotate_font(). The putcs implementations for the rotated buffer will return early in this case. See [1] for an example. Currently, fbcon_rotate_font() keeps the old buffer, which is too small for the rotated font. Printing to the rotated console with a high-enough character code will overflow the font buffer. v2: - fix typos in commit message | ||||
| CVE-2026-46190 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: mtd: spi-nor: debugfs: fix out-of-bounds read in spi_nor_params_show() Sashiko noticed an out-of-bounds read [1]. In spi_nor_params_show(), the snor_f_names array is passed to spi_nor_print_flags() using sizeof(snor_f_names). Since snor_f_names is an array of pointers, sizeof() returns the total number of bytes occupied by the pointers (element_count * sizeof(void *)) rather than the element count itself. On 64-bit systems, this makes the passed length 8x larger than intended. Inside spi_nor_print_flags(), the 'names_len' argument is used to bounds-check the 'names' array access. An out-of-bounds read occurs if a flag bit is set that exceeds the array's actual element count but is within the inflated byte-size count. Correct this by using ARRAY_SIZE() to pass the actual number of string pointers in the array. | ||||
| CVE-2026-46185 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 9.1 Critical |
| In the Linux kernel, the following vulnerability has been resolved: smb/client: fix out-of-bounds read in symlink_data() Since smb2_check_message() returns success without length validation for the symlink error response, in symlink_data() it is possible for iov->iov_len to be smaller than sizeof(struct smb2_err_rsp). If the buffer only contains the base SMB2 header (64 bytes), accessing err->ErrorContextCount (at offset 66) or err->ByteCount later in symlink_data() will cause an out-of-bounds read. | ||||
| CVE-2026-46122 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: b43: enforce bounds check on firmware key index in b43_rx() The firmware-controlled key index in b43_rx() can exceed the dev->key[] array size (58 entries). The existing B43_WARN_ON is non-enforcing in production builds, allowing an out-of-bounds read. Make the B43_WARN_ON check enforcing by dropping the frame when the firmware returns an invalid key index. | ||||
| CVE-2026-46064 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: ibmasm: fix heap over-read in ibmasm_send_i2o_message() The ibmasm_send_i2o_message() function uses get_dot_command_size() to compute the byte count for memcpy_toio(), but this value is derived from user-controlled fields in the dot_command_header (command_size: u8, data_size: u16) and is never validated against the actual allocation size. A root user can write a small buffer with inflated header fields, causing memcpy_toio() to read up to ~65 KB past the end of the allocation into adjacent kernel heap, which is then forwarded to the service processor over MMIO. Silently clamping the copy size is not sufficient: if the header fields claim a larger size than the buffer, the SP receives a dot command whose own header is inconsistent with the I2O message length, which can cause the SP to desynchronize. Reject such commands outright by returning failure. Validate command_size before calling get_mfa_inbound() to avoid leaking an I2O message frame: reading INBOUND_QUEUE_PORT dequeues a hardware frame from the controller's free pool, and returning without a corresponding set_mfa_inbound() call would permanently exhaust it. Additionally, clamp command_size to I2O_COMMAND_SIZE before the memcpy_toio() so the MMIO write stays within the I2O message frame, consistent with the clamping already performed by outgoing_message_size() for the header field. | ||||
| CVE-2026-46033 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: crypto: authencesn - reject short ahash digests during instance creation authencesn requires either a zero authsize or an authsize of at least 4 bytes because the ESN encrypt/decrypt paths always move 4 bytes of high-order sequence number data at the end of the authenticated data. While crypto_authenc_esn_setauthsize() already rejects explicit non-zero authsizes in the range 1..3, crypto_authenc_esn_create() still copied auth->digestsize into inst->alg.maxauthsize without validating it. The AEAD core then initialized the tfm's default authsize from that value. As a result, selecting an ahash with digest size 1..3, such as cbcmac(cipher_null), exposed authencesn instances whose default authsize was invalid even though setauthsize() would have rejected the same value. AF_ALG could then trigger the ESN tail handling with a too-short tag and hit an out-of-bounds access. Reject authencesn instances whose ahash digest size is in the invalid non-zero range 1..3 so that no tfm can inherit an unsupported default authsize. | ||||
| CVE-2026-46022 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: misc: ibmasm: fix OOB MMIO read in ibmasm_handle_mouse_interrupt() ibmasm_handle_mouse_interrupt() performs an out-of-bounds MMIO read when the queue reader or writer index from hardware exceeds REMOTE_QUEUE_SIZE (60). A compromised service processor can trigger this by writing an out-of-range value to the reader or writer MMIO register before asserting an interrupt. Since writer is re-read from hardware on every loop iteration, it can also be set to an out-of-range value after the loop has already started. The root cause is that get_queue_reader() and get_queue_writer() return raw readl() values that are passed directly into get_queue_entry(), which computes: queue_begin + reader * sizeof(struct remote_input) with no bounds check. This unchecked MMIO address is then passed to memcpy_fromio(), reading 8 bytes from unintended device registers. For sufficiently large values the address falls outside the PCI BAR mapping entirely, triggering a machine check exception. Fix by checking both indices against REMOTE_QUEUE_SIZE at the top of the loop body, before any call to get_queue_entry(). On an out-of-range value, reset the reader register to 0 via set_queue_reader() before breaking, so that normal queue operation can resume if the corrupted hardware state is transient. | ||||
| CVE-2026-45844 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: arp_tables: fix IEEE1394 ARP payload parsing Weiming Shi says: "arp_packet_match() unconditionally parses the ARP payload assuming two hardware addresses are present (source and target). However, IPv4-over-IEEE1394 ARP (RFC 2734) omits the target hardware address field, and arp_hdr_len() already accounts for this by returning a shorter length for ARPHRD_IEEE1394 devices. As a result, on IEEE1394 interfaces arp_packet_match() advances past a nonexistent target hardware address and reads the wrong bytes for both the target device address comparison and the target IP address. This causes arptables rules to match against garbage data, leading to incorrect filtering decisions: packets that should be accepted may be dropped and vice versa. The ARP stack in net/ipv4/arp.c (arp_create and arp_process) already handles this correctly by skipping the target hardware address for ARPHRD_IEEE1394. Apply the same pattern to arp_packet_match()." Mangle the original patch to always return 0 (no match) in case user matches on the target hardware address which is never present in IEEE1394. Note that this returns 0 (no match) for either normal and inverse match because matching in the target hardware address in ARPHRD_IEEE1394 has never been supported by arptables. This is intentional, matching on the target hardware address should never evaluate true for ARPHRD_IEEE1394. Moreover, adjust arpt_mangle to drop the packet too as AI suggests: In arpt_mangle, the logic assumes a standard ARP layout. Because IEEE1394 (FireWire) omits the target hardware address, the linear pointer arithmetic miscalculates the offset for the target IP address. This causes mangling operations to write to the wrong location, leading to packet corruption. To ensure safety, this patch drops packets (NF_DROP) when mangling is requested for these fields on IEEE1394 devices, as the current implementation cannot correctly map the FireWire ARP payload. This omits both mangling target hardware and IP address. Even if IP address mangling should be possible in IEEE1394, this would require to adjust arpt_mangle offset calculation, which has never been supported. Based on patch from Weiming Shi <bestswngs@gmail.com>. | ||||
| CVE-2026-45839 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: bpf: reject negative CO-RE accessor indices in bpf_core_parse_spec() CO-RE accessor strings are colon-separated indices that describe a path from a root BTF type to a target field, e.g. "0:1:2" walks through nested struct members. bpf_core_parse_spec() parses each component with sscanf("%d"), so negative values like -1 are silently accepted. The subsequent bounds checks (access_idx >= btf_vlen(t)) only guard the upper bound and always pass for negative values because C integer promotion converts the __u16 btf_vlen result to int, making the comparison (int)(-1) >= (int)(N) false for any positive N. When -1 reaches btf_member_bit_offset() it gets cast to u32 0xffffffff, producing an out-of-bounds read far past the members array. A crafted BPF program with a negative CO-RE accessor on any struct that exists in vmlinux BTF (e.g. task_struct) crashes the kernel deterministically during BPF_PROG_LOAD on any system with CONFIG_DEBUG_INFO_BTF=y (default on major distributions). The bug is reachable with CAP_BPF: BUG: unable to handle page fault for address: ffffed11818b6626 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page Oops: Oops: 0000 [#1] SMP KASAN NOPTI CPU: 0 UID: 0 PID: 85 Comm: poc Not tainted 7.0.0-rc6 #18 PREEMPT(full) RIP: 0010:bpf_core_parse_spec (tools/lib/bpf/relo_core.c:354) RAX: 00000000ffffffff Call Trace: <TASK> bpf_core_calc_relo_insn (tools/lib/bpf/relo_core.c:1321) bpf_core_apply (kernel/bpf/btf.c:9507) check_core_relo (kernel/bpf/verifier.c:19475) bpf_check (kernel/bpf/verifier.c:26031) bpf_prog_load (kernel/bpf/syscall.c:3089) __sys_bpf (kernel/bpf/syscall.c:6228) </TASK> CO-RE accessor indices are inherently non-negative (struct member index, array element index, or enumerator index), so reject them immediately after parsing. | ||||
| CVE-2026-45838 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: bpf: fix end-of-list detection in cgroup_storage_get_next_key() list_next_entry() never returns NULL -- when the current element is the last entry it wraps to the list head via container_of(). The subsequent NULL check is therefore dead code and get_next_key() never returns -ENOENT for the last element, instead reading storage->key from a bogus pointer that aliases internal map fields and copying the result to userspace. Replace it with list_entry_is_head() so the function correctly returns -ENOENT when there are no more entries. | ||||
| CVE-2026-23397 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: nfnetlink_osf: validate individual option lengths in fingerprints nfnl_osf_add_callback() validates opt_num bounds and string NUL-termination but does not check individual option length fields. A zero-length option causes nf_osf_match_one() to enter the option matching loop even when foptsize sums to zero, which matches packets with no TCP options where ctx->optp is NULL: Oops: general protection fault KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] RIP: 0010:nf_osf_match_one (net/netfilter/nfnetlink_osf.c:98) Call Trace: nf_osf_match (net/netfilter/nfnetlink_osf.c:227) xt_osf_match_packet (net/netfilter/xt_osf.c:32) ipt_do_table (net/ipv4/netfilter/ip_tables.c:293) nf_hook_slow (net/netfilter/core.c:623) ip_local_deliver (net/ipv4/ip_input.c:262) ip_rcv (net/ipv4/ip_input.c:573) Additionally, an MSS option (kind=2) with length < 4 causes out-of-bounds reads when nf_osf_match_one() unconditionally accesses optp[2] and optp[3] for MSS value extraction. While RFC 9293 section 3.2 specifies that the MSS option is always exactly 4 bytes (Kind=2, Length=4), the check uses "< 4" rather than "!= 4" because lengths greater than 4 do not cause memory safety issues -- the buffer is guaranteed to be at least foptsize bytes by the ctx->optsize == foptsize check. Reject fingerprints where any option has zero length, or where an MSS option has length less than 4, at add time rather than trusting these values in the packet matching hot path. | ||||
| CVE-2026-23388 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: Squashfs: check metadata block offset is within range Syzkaller reports a "general protection fault in squashfs_copy_data" This is ultimately caused by a corrupted index look-up table, which produces a negative metadata block offset. This is subsequently passed to squashfs_copy_data (via squashfs_read_metadata) where the negative offset causes an out of bounds access. The fix is to check that the offset is within range in squashfs_read_metadata. This will trap this and other cases. | ||||
| CVE-2026-23318 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Use correct version for UAC3 header validation The entry of the validators table for UAC3 AC header descriptor is defined with the wrong protocol version UAC_VERSION_2, while it should have been UAC_VERSION_3. This results in the validator never matching for actual UAC3 devices (protocol == UAC_VERSION_3), causing their header descriptors to bypass validation entirely. A malicious USB device presenting a truncated UAC3 header could exploit this to cause out-of-bounds reads when the driver later accesses unvalidated descriptor fields. The bug was introduced in the same commit as the recently fixed UAC3 feature unit sub-type typo, and appears to be from the same copy-paste error when the UAC3 section was created from the UAC2 section. | ||||
| CVE-2026-23315 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: Fix possible oob access in mt76_connac2_mac_write_txwi_80211() Check frame length before accessing the mgmt fields in mt76_connac2_mac_write_txwi_80211 in order to avoid a possible oob access. [fix check to also cover mgmt->u.action.u.addba_req.capab, correct Fixes tag] | ||||
| CVE-2026-23204 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: net/sched: cls_u32: use skb_header_pointer_careful() skb_header_pointer() does not fully validate negative @offset values. Use skb_header_pointer_careful() instead. GangMin Kim provided a report and a repro fooling u32_classify(): BUG: KASAN: slab-out-of-bounds in u32_classify+0x1180/0x11b0 net/sched/cls_u32.c:221 | ||||
| CVE-2025-38736 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: net: usb: asix_devices: Fix PHY address mask in MDIO bus initialization Syzbot reported shift-out-of-bounds exception on MDIO bus initialization. The PHY address should be masked to 5 bits (0-31). Without this mask, invalid PHY addresses could be used, potentially causing issues with MDIO bus operations. Fix this by masking the PHY address with 0x1f (31 decimal) to ensure it stays within the valid range. | ||||