| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: auth: verify auth requirement when auth_chunk is NULL
sctp_auth_chunk_verify() returns true unconditionally when
chunk->auth_chunk is NULL, silently skipping authentication.
This is incorrect when:
1. skb_clone() failed in the BH receive path, leaving auth_chunk
NULL. In sctp_endpoint_bh_rcv() asoc is NULL for new
connections, so the early sctp_auth_recv_cid() check cannot
catch this.
2. No AUTH chunk precedes COOKIE-ECHO, so skb_clone() is never
called and auth_chunk remains NULL.
Fix by checking sctp_auth_recv_cid() when auth_chunk is NULL:
if authentication is required, return false to drop the chunk;
otherwise continue normally. |
| In the Linux kernel, the following vulnerability has been resolved:
vmxnet3: fix BUG_ON in vmxnet3_get_hdr_len() for Geneve packets
vmxnet3_get_hdr_len() assumes gdesc->rcd.v4/v6/tcp always describe the
outer header, but for a Geneve-encapsulated packet the device can set
them based on the inner header instead, signalled by the
VMXNET3_RCD_HDR_INNER_SHIFT bit in the completion descriptor. Since the
function never skips the outer encapsulation, this mismatch triggers:
- BUG_ON(hdr.ipv4->protocol != IPPROTO_TCP), because the outer
protocol is UDP (Geneve), not TCP.
- BUG_ON(hdr.eth->h_proto != ...), when the tunnel's outer and inner
IP versions differ (e.g. outer IPv6/inner IPv4 or vice versa).
Check VMXNET3_RCD_HDR_INNER_SHIFT up front and bail out, since the
function cannot locate the inner header it would need to parse. Also
convert the remaining BUG_ON()s in this function to return 0
defensively. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/vm: Fix SVM leak on resv obj alloc failure in xe_vm_create()
Commit 9e9787414882 ("drm/xe/userptr: replace xe_hmm with gpusvm") made
xe_svm_init() unconditional in xe_vm_create() and extended it to also
initialize a "simple" gpusvm state for non-fault-mode VMs. The matching
xe_svm_fini() call in xe_vm_close_and_put() was updated to run
unconditionally, but the error unwind path in xe_vm_create() was not.
On the drm_gpuvm_resv_object_alloc() failure path, xe_svm_init() has
already succeeded but xe_svm_fini() is only called when
XE_VM_FLAG_FAULT_MODE is set. For non-fault-mode VMs this leaves
vm->svm.gpusvm partially initialized and leaks the resources allocated
by drm_gpusvm_init().
For fault-mode VMs, xe_svm_init() additionally acquires the pagemap
owner via drm_pagemap_acquire_owner() and the pagemaps via
xe_svm_get_pagemaps(). Those resources are released by xe_svm_close(),
not xe_svm_fini(). On the same error path, xe_svm_close() is not
called either, so fault-mode VMs leak the pagemap owner and pagemaps.
Fix both leaks:
- Call xe_svm_fini() unconditionally on the err_svm_fini path, matching
the unconditional xe_svm_init() call. Move the vm->size = 0
assignment out of the conditional so the xe_vm_is_closed() assert in
xe_svm_fini() (and xe_svm_close()) holds for both modes.
- Call xe_svm_close() for fault-mode VMs before xe_svm_fini(), matching
the ordering used in xe_vm_close_and_put().
(cherry picked from commit ca2a3587d577ba764e0fe628fb676244fc33ddd4) |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix u16 MTU truncation in media and bearer MTU validation
Both TIPC_NL_MEDIA_SET and TIPC_NL_BEARER_SET accept user-supplied
MTU values but only enforce a minimum bound, not a maximum. When a user
sets the MTU to a value exceeding U16_MAX (65535), it passes validation
but is silently truncated when assigned to u16 fields l->mtu and
l->advertised_mtu in tipc_link_create(). Values like 65536 (0x10000)
truncate to 0, causing a division by zero in tipc_link_set_queue_limits()
which computes TIPC_MAX_PUBL / (l->mtu / ITEM_SIZE). Other overflowing
values (e.g. 65537-131071) produce small incorrect MTU values, resulting
in link malfunction behaviors.
Crash stack (triggered as unprivileged user via user namespace):
tipc_link_set_queue_limits net/tipc/link.c:2531
tipc_link_create net/tipc/link.c:520
tipc_node_check_dest net/tipc/node.c:1279
tipc_disc_rcv net/tipc/discover.c:252
tipc_rcv net/tipc/node.c:2129
tipc_udp_recv net/tipc/udp_media.c:392
Two independent paths lack the upper bound check:
1. tipc_udp_mtu_bad() -- called from __tipc_nl_media_set() (MEDIA_SET)
2. inline check in __tipc_nl_bearer_set() at bearer.c:1160 (BEARER_SET)
Fix both by rejecting MTU values above U16_MAX. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: restrict socket creation to the initial network namespace
QRTR keeps its entire port and node state in module-global variables
that are not partitioned per network namespace: qrtr_local_nid is a
single global node id (always 1) and qrtr_ports is a single global
xarray. qrtr_port_lookup() and qrtr_local_enqueue() operate on that
global state with no network-namespace check, and qrtr_create() places
no restriction on the namespace a socket is created in.
As a result an unprivileged process that creates an AF_QIPCRTR socket
in a separate network namespace, e.g. via
unshare(CLONE_NEWUSER | CLONE_NEWNET), can send QRTR datagrams -
including control-plane messages such as QRTR_TYPE_NEW_SERVER - to QRTR
sockets owned by another namespace, and vice versa. The receiving
socket sees such a message as coming from node id 1, indistinguishable
from a legitimate local client, breaking the isolation that network
namespaces are expected to provide.
QRTR is a transport to global hardware endpoints (the modem and other
remote processors) and has no per-namespace semantics; its in-kernel
name service already creates its socket in init_net only. Confine the
socket family to the initial network namespace, as other
non-namespace-aware socket families do (see llc_ui_create() and the
ieee802154 socket code). |
| In the Linux kernel, the following vulnerability has been resolved:
rds: tcp: unregister sysctl before tearing down listen socket
rds_tcp_exit_net() frees the per-netns RDS TCP listen socket via
rds_tcp_kill_sock() before unregistering the per-netns sysctl table. Since
rds_tcp_skbuf_handler() derives the netns from
rtn->rds_tcp_listen_sock->sk, a concurrent sysctl write can race with
netns teardown and dereference the freed socket/sk.
KASAN reports the race as:
BUG: KASAN: slab-use-after-free in rds_tcp_skbuf_handler+0x2aa/0x2e0
rds_tcp_skbuf_handler net/rds/tcp.c:721
proc_sys_call_handler fs/proc/proc_sysctl.c
vfs_write fs/read_write.c
__x64_sys_pwrite64 fs/read_write.c
Fix this by unregistering the RDS TCP sysctl table before calling
rds_tcp_kill_sock(). unregister_net_sysctl_table() prevents new sysctl
handlers from starting and waits for in-flight handlers to finish, so
the listen socket can then be released safely. The fix was tested
against the linked reproducer. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Fix cork use-after-free in tcp_bpf_sendmsg()
tcp_bpf_sendmsg() keeps msg_tx across sk_stream_wait_memory(), which
drops and reacquires the socket lock. Its error path tries to decide
whether msg_tx names the local temporary message by comparing it with
the current value of psock->cork.
This comparison is unsafe when two threads send on the same socket:
Thread A Thread B
msg_tx = psock->cork
sk_msg_alloc() fails
sk_stream_wait_memory()
releases the socket lock acquires the socket lock
completes the cork
psock->cork = NULL
frees the cork
reacquires the socket lock
msg_tx != psock->cork
sk_msg_free(msg_tx)
The stale cork is therefore mistaken for the local temporary message
and freed again. KASAN reported:
BUG: KASAN: slab-use-after-free in sk_msg_free+0x49/0x50
Read of size 4 at addr ffff88810c908800 by task poc/90
Call Trace:
sk_msg_free+0x49/0x50
tcp_bpf_sendmsg+0x14f5/0x1cc0
__sys_sendto+0x32c/0x3a0
__x64_sys_sendto+0xdb/0x1b0
Allocated by task 89:
__kasan_kmalloc+0x8f/0xa0
tcp_bpf_sendmsg+0x16b3/0x1cc0
Freed by task 91:
__kasan_slab_free+0x43/0x70
kfree+0x131/0x3c0
tcp_bpf_sendmsg+0xec3/0x1cc0
msg_tx can only name the stack-local tmp or the shared cork. Check for
tmp directly so a changed psock->cork cannot turn a shared message into
an apparent local one. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Hold a dma-buf reference for imported BOs
An imported dma-buf BO is created as a ttm_bo_type_sg BO whose
reservation object is the exporter's dma_buf->resv. The importer,
however, only takes a dma-buf reference after a successful
dma_buf_dynamic_attach(). Until then nothing keeps the exporter alive,
so if the exporter is freed while the BO still references its resv, a
later access to that resv is a use-after-free:
Oops: general protection fault, probably for non-canonical address
0x6b6b6b6b6b6b6b9c
Workqueue: ttm ttm_bo_delayed_delete [ttm]
RIP: 0010:mutex_can_spin_on_owner+0x3f/0xc0
This can be reached on two paths:
- dma_buf_dynamic_attach() fails, or
- ttm_bo_init_reserved() fails during BO creation.
In both cases the BO already has bo->base.resv pointing at the exporter
resv, and sg BOs are always torn down via ttm_bo_delayed_delete(), which
locks bo->base.resv asynchronously - potentially after the exporter has
been freed.
Take the dma-buf reference in xe_bo_init_locked(), before
ttm_bo_init_reserved(), so it also covers a creation failure there, and
release it in xe_ttm_bo_destroy(). The reference is held for the whole
BO lifetime, keeping the shared resv alive on every path.
v2:
- Reworked the fix to avoid creating the imported sg BO before
dma_buf_dynamic_attach() succeeds.
- Attach with importer_priv == NULL and make invalidate_mappings ignore
incomplete imports.
v3:
- Dropped the xe-side reordering approach since importer_priv must be
valid when dma_buf_dynamic_attach() publishes the attachment.
- Per Christian's suggestion on the v1 thread, keyed the check on
import_attach rather than removing the sg guard entirely.
- Fixes both xe and amdgpu in a single TTM patch.
v4:
- Moved import_attach check to after dma_resv_copy_fences() so fences
are copied before returning for successful imports (Thomas).
- Removed exporter-alive claim from commit message (Thomas).
v5:
- Add drm/xe patch to keep imported sg BOs off the LRU before attach
succeeds; the TTM fix alone is not sufficient for xe if the BO is
already LRU-visible. (Thomas)
v4 patch:
https://patchwork.freedesktop.org/patch/736663/?series=169129&rev=2
- Patch 1 (drm/ttm) carries Christian's Reviewed-by from v4.
v6:
- Reworked the fix based on Thomas' suggestion. Instead of the TTM resv
individualization (v1-v5) plus the xe off-LRU/placement handling (v5),
just hold a dma-buf reference for the imported BO lifetime so the
shared resv can never be freed while the BO still references it.
Single xe patch, no TTM change. (Thomas)
- Take the reference in xe_bo_init_locked() before ttm_bo_init_reserved()
so a TTM creation failure is covered too (Thomas).
- Dropped the v5 series (drm/ttm + drm/xe off-LRU); the off-LRU approach
also regressed in CI BAT via ttm_bo_pipeline_gutting() creating a ghost
BO that outlived the exporter.
Link to v5: https://patchwork.freedesktop.org/series/169984/
v7:
- Move changelog above --- so it stays in the commit message.
- Reorder changelog entries oldest-to-newest. (Thomas)
(cherry picked from commit 3516f3fae6be35642f8f06f8a218da6425c0306a) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/vm: Fix BO prefetch with CONSULT_MEM_ADVISE_PREF_LOC
When prefetch region is DRM_XE_CONSULT_MEM_ADVISE_PREF_LOC for a BO VMA,
the code used it as an index into region_to_mem_type[], causing an
out-of-bounds access since the value is -1.
Resolve the preferred location for BO VMAs directly: local VRAM on dGFX
(using the BO's tile placement) or system memory on iGPU.
Discovered using AI-assisted static analysis confirmed by Intel Product
Security.
v2:
-Fix null dereference
(cherry picked from commit d9a4906ac03be9f6ed3f3b45c56c866b867fd75b) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/pt: Reset current_op in xe_pt_update_ops_init()
xe_pt_update_ops_init() fails to reset current_op to 0. On the
vm_bind path, ops_execute() calls xe_pt_update_ops_prepare() inside
the xe_validation_guard() / drm_exec_until_all_locked() loop. When
that loop retries due to lock contention or OOM eviction
(drm_exec_retry_on_contention() / xe_validation_retry_on_oom()),
xe_pt_update_ops_prepare() runs again on the same vops, and each
call to bind_op_prepare() increments current_op without resetting it.
After N retries current_op exceeds the array size allocated by
xe_vma_ops_alloc(), causing an out-of-bounds write into
SLUB-poisoned memory and a subsequent UAF crash in
xe_migrate_update_pgtables_cpu() when reading the corrupted pt_op->bind.
Also reset needs_svm_lock and needs_invalidation which are derived in
the same prepare pass and would otherwise cause wrong migrate ops
selection and redundant TLB invalidation on retry.
Fix this by resetting current_op, needs_svm_lock and needs_invalidation
in xe_pt_update_ops_init().
v2 (Matt):
- Add details in commit message.
- Add Fixes tag and Cc to stable@vger.kernel.org
(cherry picked from commit 046045543e530605c441063535e7dca0075369a6) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: fix 32-bit overflow in CWSR total size calculation
total_cwsr_size was computed in 32-bit before being used as a BO/SVM
allocation size.
With large ctx_save_restore_area_size and debug_memory_size
multiplied by the XCC count, the product can wrap,
yielding an undersized CWSR save area that firmware later overruns.
Promote total_cwsr_size to u64 and use check_add_overflow()/
check_mul_overflow() in both kfd_queue_acquire_buffers() and
kfd_queue_release_buffers().
(cherry picked from commit 319f7e13423ae3f486b9aea82f9ad2d6af0ee608) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: bound EDID block reads to the response buffer
virtio_get_edid_block() validates the read offset only against the
device-supplied resp->size field, never against the fixed-size resp->edid
array. The EDID block index is driven by the device-supplied extension
count, so a malicious virtio-gpu backend can advertise a large size
together with a high block count and read far past the array into adjacent
kernel memory, which is then surfaced in the parsed EDID (an out-of-bounds
read / info leak).
Also reject any read whose end exceeds the size of the edid array.
Conforming EDID responses stay within the array and are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/hdcp: check streams[] bounds before overflow
The data->streams[] overflow check is done after the buffer overflow has
already happened. Move the overflow check before the write.
Side note, emitting a warning splat with a backtrace might be overkill
here, but prefer not changing the behaviour other than not doing the
overrun.
Discovered using AI-assisted static analysis confirmed by Intel Product
Security.
(cherry picked from commit 9284ab3b6e776c315883ac2611283d263c9460fd) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix lifetime issue of amdgpu_vm_get_task_info_pasid()
The vm pointer returned from amdgpu_vm_get_vm_from_pasid() is only
valid while the lock is still being held. Once xa_unlock_irqrestore is
called and returned, the pointer is no longer under lock and is subject
to modification. Since, the caller still dereferences vm->task_info in
amdgpu_vm_get_task_info_vm() after the lock is removed, this causes a
use after unlock problem.
Remove the lifetime issue present in amdgpu_vm_get_task_info_pasid()
through removing the amdgpu_vm_get_vm_from_pasid() function from
amdgpu_vm.c and making the relevant code inline to hold the lock while
it is still in use.
(cherry picked from commit 9d01579f3f868b333acc901815972685989092c7) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gpusvm: publish dpagemap early to avoid device mapping leak on error
drm_gpusvm_get_pages() only stored the local dpagemap into
svm_pages->dpagemap on the success path. If a later page failed (e.g.
-EOPNOTSUPP when ctx->allow_mixed is false) and jumped to err_unmap,
svm_pages->dpagemap was still NULL, so __drm_gpusvm_unmap_pages() skipped
device_unmap() and leaked the device mappings already created.
Assign svm_pages->dpagemap when the first device page is mapped so the
err_unmap path can device_unmap() those mappings.
This issue was found by Sashiko AI review. |
| In the Linux kernel, the following vulnerability has been resolved:
media: pwc: Return queued buffers on start_streaming() failure
The vb2 framework hands buffers to the driver via buf_queue() before
calling start_streaming(). If start_streaming() returns an error
without first returning those buffers via vb2_buffer_done(),
vb2_start_streaming() fires WARN_ON(owned_by_drv_count) and the queued
buffers leak.
pwc's start_streaming() had two early returns that hit this trap:
-ENODEV when the USB device was already disconnected, and -ERESTARTSYS
when mutex_lock_interruptible() was interrupted by a signal. Call the
existing pwc_cleanup_queued_bufs() helper with VB2_BUF_STATE_QUEUED
before returning (matching the state already used by the
pwc_isoc_init() error path in the same function).
This mirrors the uvcvideo fix in commit 4cf3b6fd54eb ("media: uvcvideo:
Return queued buffers on start_streaming() failure"). |
| In the Linux kernel, the following vulnerability has been resolved:
media: rtl2832_sdr: Return queued buffers on start_streaming() failure
The vb2 framework hands buffers to the driver via buf_queue() before
calling start_streaming(). If start_streaming() returns an error
without first returning those buffers via vb2_buffer_done(),
vb2_start_streaming() fires WARN_ON(owned_by_drv_count) and the queued
buffers leak.
rtl2832_sdr_start_streaming() had multiple error paths that hit this
trap: two direct early returns (-ENODEV, -ERESTARTSYS), plus six
`goto err` paths covering subdev s_power, tuner setup, ADC setup,
stream-buffer allocation, urb allocation, and urb submission failures.
None of them returned the queued buffers.
The original function had no distinct success exit and fell straight
through into the err label, which previously only did mutex_unlock and
"return ret". Adding queued-buffer cleanup at err must therefore be
paired with an explicit success return; otherwise every successful
start would also drain the buffer queue and kill streaming. Add that
success return, then add rtl2832_sdr_cleanup_queued_bufs() at the err
label and before each early return.
The cleanup helper takes a vb2_buffer_state argument so that the
start_streaming error paths can pass VB2_BUF_STATE_QUEUED (as
expected by userspace on start_streaming failure) while stop_streaming
keeps its existing VB2_BUF_STATE_ERROR semantics.
This mirrors the uvcvideo fix in commit 4cf3b6fd54eb ("media: uvcvideo:
Return queued buffers on start_streaming() failure").
The err label still does not roll back power_ctrl(), frontend_ctrl(),
the POWER_ON flag, or stream/URB allocations that may have happened
before the failing step. Those are pre-existing leaks of a different
class and are not addressed here. |
| In the Linux kernel, the following vulnerability has been resolved:
media: v4l2-ctrls: validate HEVC active reference counts
HEVC slice parameters are shared stateless V4L2 controls, but the common
validation path does not verify the active L0/L1 reference counts before
driver-specific code consumes them.
The original report came from Cedrus, but the active count bounds are
not Cedrus-specific. Validate them in the common HEVC slice control path
so stateless HEVC drivers get the same basic guarantees as soon as the
control is queued.
Do not reject ref_idx_l0/ref_idx_l1 entries here. Existing userspace may
use out-of-range sentinel values such as 0xff for missing references, and
some hardware can use that information for concealment. Keep this common
check limited to the active reference counts. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: close a re-opened queue timer in the destructor
queue_delete() closes the queue timer, then frees it. snd_seq_timer_close()
clears q->timer->timeri. snd_use_lock_sync() then drains borrowers, and
snd_seq_timer_delete() frees q->timer.
A borrower can re-open the timer inside that window. A SET_QUEUE_CLIENT
that took a queueptr() use_lock reference before the queue was unlinked
runs snd_seq_timer_open() after the close. Open refuses re-open only while
timeri is set, and the close just cleared it, so it re-opens timeri.
snd_seq_timer_delete() does not close that instance. Its snd_seq_timer_stop()
is a no-op, because running was cleared first. So it frees q->timer with the
instance still live. The queue is freed next.
The instance stays on the global timer with callback_data pointing at the
freed queue. A non-owner START on the unlocked queue arms it. The next tick
derefs the freed queue in snd_seq_timer_interrupt().
Reachable by an unprivileged user with access to /dev/snd/seq. No CAP and
no queue ownership required.
Close any lingering instance in the destructor. There, ->timeri can no
longer change: the queue is unlinked and all use_lock borrowers have
drained, so no snd_seq_queue_use() can re-open it. Close it before clearing
q->timer. snd_timer_close() waits for any in-flight snd_seq_timer_interrupt()
to finish, and that callback still reads q->timer (via snd_seq_check_queue()),
so q->timer must stay valid until it drains. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: timer: drain a slave's callback before its master detaches it
snd_timer_close_locked() drains the closing instance's own in-flight
callback (IFLG_CALLBACK) before freeing it, but not its slaves'. When a
master instance is closed, remove_slave_links() clears each slave's
->timer; the slave's own close then reads timer == NULL and takes the
branch that skips the drain entirely (snd_timer_stop_slave() also no-ops
on a NULL timer). So a slave whose callback is still running when the
master is closed is freed underneath the live callback, leading to
use-after-free.
Drain the slaves too before remove_slave_links() severs them.
snd_timer_stop() has already taken this instance off the active list, so
no new slave callback can be queued. Take the slaves off the ack list so
a pending one can't fire either, then wait for any that is already in
flight. |
