| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
HSI: ssi_protocol: fix potential resource leak in ssip_pn_open()
ssip_pn_open() claims the HSI client's port with hsi_claim_port(). When
hsi_register_port_event() gets some error and returns a negetive value,
the HSI client's port should be released with hsi_release_port().
Fix it by calling hsi_release_port() when hsi_register_port_event() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: avoid uninit memory read in ath9k_htc_rx_msg()
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/kprobes: Fix null pointer reference in arch_prepare_kprobe()
I found a null pointer reference in arch_prepare_kprobe():
# echo 'p cmdline_proc_show' > kprobe_events
# echo 'p cmdline_proc_show+16' >> kprobe_events
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc000000000050bfc
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA PowerNV
Modules linked in:
CPU: 0 PID: 122 Comm: sh Not tainted 6.0.0-rc3-00007-gdcf8e5633e2e #10
NIP: c000000000050bfc LR: c000000000050bec CTR: 0000000000005bdc
REGS: c0000000348475b0 TRAP: 0300 Not tainted (6.0.0-rc3-00007-gdcf8e5633e2e)
MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 88002444 XER: 20040006
CFAR: c00000000022d100 DAR: 0000000000000000 DSISR: 40000000 IRQMASK: 0
...
NIP arch_prepare_kprobe+0x10c/0x2d0
LR arch_prepare_kprobe+0xfc/0x2d0
Call Trace:
0xc0000000012f77a0 (unreliable)
register_kprobe+0x3c0/0x7a0
__register_trace_kprobe+0x140/0x1a0
__trace_kprobe_create+0x794/0x1040
trace_probe_create+0xc4/0xe0
create_or_delete_trace_kprobe+0x2c/0x80
trace_parse_run_command+0xf0/0x210
probes_write+0x20/0x40
vfs_write+0xfc/0x450
ksys_write+0x84/0x140
system_call_exception+0x17c/0x3a0
system_call_vectored_common+0xe8/0x278
--- interrupt: 3000 at 0x7fffa5682de0
NIP: 00007fffa5682de0 LR: 0000000000000000 CTR: 0000000000000000
REGS: c000000034847e80 TRAP: 3000 Not tainted (6.0.0-rc3-00007-gdcf8e5633e2e)
MSR: 900000000280f033 <SF,HV,VEC,VSX,EE,PR,FP,ME,IR,DR,RI,LE> CR: 44002408 XER: 00000000
The address being probed has some special:
cmdline_proc_show: Probe based on ftrace
cmdline_proc_show+16: Probe for the next instruction at the ftrace location
The ftrace-based kprobe does not generate kprobe::ainsn::insn, it gets
set to NULL. In arch_prepare_kprobe() it will check for:
...
prev = get_kprobe(p->addr - 1);
preempt_enable_no_resched();
if (prev && ppc_inst_prefixed(ppc_inst_read(prev->ainsn.insn))) {
...
If prev is based on ftrace, 'ppc_inst_read(prev->ainsn.insn)' will occur
with a null pointer reference. At this point prev->addr will not be a
prefixed instruction, so the check can be skipped.
Check if prev is ftrace-based kprobe before reading 'prev->ainsn.insn'
to fix this problem.
[mpe: Trim oops] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix monitor mode bringup crash
When the interface is brought up in monitor mode, it leads
to NULL pointer dereference crash. This crash happens when
the packet type is extracted for a SKB. This extraction
which is present in the received msdu delivery path,is
not needed for the monitor ring packets since they are
all RAW packets. Hence appending the flags with
"RX_FLAG_ONLY_MONITOR" to skip that extraction.
Observed calltrace:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000064
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=0000000048517000
[0000000000000064] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
Modules linked in: ath11k_pci ath11k qmi_helpers
CPU: 2 PID: 1781 Comm: napi/-271 Not tainted
6.1.0-rc5-wt-ath-656295-gef907406320c-dirty #6
Hardware name: Qualcomm Technologies, Inc. IPQ8074/AP-HK10-C2 (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k]
lr : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x5c/0x60 [ath11k]
sp : ffff80000ef5bb10
x29: ffff80000ef5bb10 x28: 0000000000000000 x27: ffff000007baafa0
x26: ffff000014a91ed0 x25: 0000000000000000 x24: 0000000000000000
x23: ffff800002b77378 x22: ffff000014a91ec0 x21: ffff000006c8d600
x20: 0000000000000000 x19: ffff800002b77740 x18: 0000000000000006
x17: 736564203634343a x16: 656e694c20657079 x15: 0000000000000143
x14: 00000000ffffffea x13: ffff80000ef5b8b8 x12: ffff80000ef5b8c8
x11: ffff80000a591d30 x10: ffff80000a579d40 x9 : c0000000ffffefff
x8 : 0000000000000003 x7 : 0000000000017fe8 x6 : ffff80000a579ce8
x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 3a35ec12ed7f8900 x1 : 0000000000000000 x0 : 0000000000000052
Call trace:
ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k]
ath11k_dp_rx_deliver_msdu.isra.42+0xa4/0x3d0 [ath11k]
ath11k_dp_rx_mon_deliver.isra.43+0x2f8/0x458 [ath11k]
ath11k_dp_rx_process_mon_rings+0x310/0x4c0 [ath11k]
ath11k_dp_service_srng+0x234/0x338 [ath11k]
ath11k_pcic_ext_grp_napi_poll+0x30/0xb8 [ath11k]
__napi_poll+0x5c/0x190
napi_threaded_poll+0xf0/0x118
kthread+0xf4/0x110
ret_from_fork+0x10/0x20
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: avoid SBSA UART accessing DMACR register
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html |
| In the Linux kernel, the following vulnerability has been resolved:
devlink: hold region lock when flushing snapshots
Netdevsim triggers a splat on reload, when it destroys regions
with snapshots pending:
WARNING: CPU: 1 PID: 787 at net/core/devlink.c:6291 devlink_region_snapshot_del+0x12e/0x140
CPU: 1 PID: 787 Comm: devlink Not tainted 6.1.0-07460-g7ae9888d6e1c #580
RIP: 0010:devlink_region_snapshot_del+0x12e/0x140
Call Trace:
<TASK>
devl_region_destroy+0x70/0x140
nsim_dev_reload_down+0x2f/0x60 [netdevsim]
devlink_reload+0x1f7/0x360
devlink_nl_cmd_reload+0x6ce/0x860
genl_family_rcv_msg_doit.isra.0+0x145/0x1c0
This is the locking assert in devlink_region_snapshot_del(),
we're supposed to be holding the region->snapshot_lock here. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/erdma: Fix refcount leak in erdma_mmap
rdma_user_mmap_entry_get() take reference, we should release it when not
need anymore, add the missing rdma_user_mmap_entry_put() in the error
path to fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: visconti: Fix memory leak in visconti_register_pll()
@pll->rate_table has allocated memory by kmemdup(), if clk_hw_register()
fails, it should be freed, otherwise it will cause memory leak issue,
this patch fixes it. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix potential memory leak in ext4_fc_record_modified_inode()
As krealloc may return NULL, in this case 'state->fc_modified_inodes'
may not be freed by krealloc, but 'state->fc_modified_inodes' already
set NULL. Then will lead to 'state->fc_modified_inodes' memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/powerplay/psm: Fix memory leak in power state init
Commit 902bc65de0b3 ("drm/amdgpu/powerplay/psm: return an error in power
state init") made the power state init function return early in case of
failure to get an entry from the powerplay table, but it missed to clean up
the allocated memory for the current power state before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
of: overlay: fix null pointer dereferencing in find_dup_cset_node_entry() and find_dup_cset_prop()
When kmalloc() fail to allocate memory in kasprintf(), fn_1 or fn_2 will
be NULL, and strcmp() will cause null pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921e: fix rmmod crash in driver reload test
In insmod/rmmod stress test, the following crash dump shows up immediately.
The problem is caused by missing mt76_dev in mt7921_pci_remove(). We
should make sure the drvdata is ready before probe() finished.
[168.862789] ==================================================================
[168.862797] BUG: KASAN: user-memory-access in try_to_grab_pending+0x59/0x480
[168.862805] Write of size 8 at addr 0000000000006df0 by task rmmod/5361
[168.862812] CPU: 7 PID: 5361 Comm: rmmod Tainted: G OE 5.19.0-rc6 #1
[168.862816] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, 05/04/2020
[168.862820] Call Trace:
[168.862822] <TASK>
[168.862825] dump_stack_lvl+0x49/0x63
[168.862832] print_report.cold+0x493/0x6b7
[168.862845] kasan_report+0xa7/0x120
[168.862857] kasan_check_range+0x163/0x200
[168.862861] __kasan_check_write+0x14/0x20
[168.862866] try_to_grab_pending+0x59/0x480
[168.862870] __cancel_work_timer+0xbb/0x340
[168.862898] cancel_work_sync+0x10/0x20
[168.862902] mt7921_pci_remove+0x61/0x1c0 [mt7921e]
[168.862909] pci_device_remove+0xa3/0x1d0
[168.862914] device_remove+0xc4/0x170
[168.862920] device_release_driver_internal+0x163/0x300
[168.862925] driver_detach+0xc7/0x1a0
[168.862930] bus_remove_driver+0xeb/0x2d0
[168.862935] driver_unregister+0x71/0xb0
[168.862939] pci_unregister_driver+0x30/0x230
[168.862944] mt7921_pci_driver_exit+0x10/0x1b [mt7921e]
[168.862949] __x64_sys_delete_module+0x2f9/0x4b0
[168.862968] do_syscall_64+0x38/0x90
[168.862973] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Test steps:
1. insmode
2. do not ifup
3. rmmod quickly (within 1 second) |
| In the Linux kernel, the following vulnerability has been resolved:
blk-throttle: prevent overflow while calculating wait time
There is a problem found by code review in tg_with_in_bps_limit() that
'bps_limit * jiffy_elapsed_rnd' might overflow. Fix the problem by
calling mul_u64_u64_div_u64() instead. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: stop mdx_raid1 thread when raid1 array run failed
fail run raid1 array when we assemble array with the inactive disk only,
but the mdx_raid1 thread were not stop, Even if the associated resources
have been released. it will caused a NULL dereference when we do poweroff.
This causes the following Oops:
[ 287.587787] BUG: kernel NULL pointer dereference, address: 0000000000000070
[ 287.594762] #PF: supervisor read access in kernel mode
[ 287.599912] #PF: error_code(0x0000) - not-present page
[ 287.605061] PGD 0 P4D 0
[ 287.607612] Oops: 0000 [#1] SMP NOPTI
[ 287.611287] CPU: 3 PID: 5265 Comm: md0_raid1 Tainted: G U 5.10.146 #0
[ 287.619029] Hardware name: xxxxxxx/To be filled by O.E.M, BIOS 5.19 06/16/2022
[ 287.626775] RIP: 0010:md_check_recovery+0x57/0x500 [md_mod]
[ 287.632357] Code: fe 01 00 00 48 83 bb 10 03 00 00 00 74 08 48 89 ......
[ 287.651118] RSP: 0018:ffffc90000433d78 EFLAGS: 00010202
[ 287.656347] RAX: 0000000000000000 RBX: ffff888105986800 RCX: 0000000000000000
[ 287.663491] RDX: ffffc90000433bb0 RSI: 00000000ffffefff RDI: ffff888105986800
[ 287.670634] RBP: ffffc90000433da0 R08: 0000000000000000 R09: c0000000ffffefff
[ 287.677771] R10: 0000000000000001 R11: ffffc90000433ba8 R12: ffff888105986800
[ 287.684907] R13: 0000000000000000 R14: fffffffffffffe00 R15: ffff888100b6b500
[ 287.692052] FS: 0000000000000000(0000) GS:ffff888277f80000(0000) knlGS:0000000000000000
[ 287.700149] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 287.705897] CR2: 0000000000000070 CR3: 000000000320a000 CR4: 0000000000350ee0
[ 287.713033] Call Trace:
[ 287.715498] raid1d+0x6c/0xbbb [raid1]
[ 287.719256] ? __schedule+0x1ff/0x760
[ 287.722930] ? schedule+0x3b/0xb0
[ 287.726260] ? schedule_timeout+0x1ed/0x290
[ 287.730456] ? __switch_to+0x11f/0x400
[ 287.734219] md_thread+0xe9/0x140 [md_mod]
[ 287.738328] ? md_thread+0xe9/0x140 [md_mod]
[ 287.742601] ? wait_woken+0x80/0x80
[ 287.746097] ? md_register_thread+0xe0/0xe0 [md_mod]
[ 287.751064] kthread+0x11a/0x140
[ 287.754300] ? kthread_park+0x90/0x90
[ 287.757974] ret_from_fork+0x1f/0x30
In fact, when raid1 array run fail, we need to do
md_unregister_thread() before raid1_free(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ar5523: Fix use-after-free on ar5523_cmd() timed out
syzkaller reported use-after-free with the stack trace like below [1]:
[ 38.960489][ C3] ==================================================================
[ 38.963216][ C3] BUG: KASAN: use-after-free in ar5523_cmd_tx_cb+0x220/0x240
[ 38.964950][ C3] Read of size 8 at addr ffff888048e03450 by task swapper/3/0
[ 38.966363][ C3]
[ 38.967053][ C3] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.0.0-09039-ga6afa4199d3d-dirty #18
[ 38.968464][ C3] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.fc36 04/01/2014
[ 38.969959][ C3] Call Trace:
[ 38.970841][ C3] <IRQ>
[ 38.971663][ C3] dump_stack_lvl+0xfc/0x174
[ 38.972620][ C3] print_report.cold+0x2c3/0x752
[ 38.973626][ C3] ? ar5523_cmd_tx_cb+0x220/0x240
[ 38.974644][ C3] kasan_report+0xb1/0x1d0
[ 38.975720][ C3] ? ar5523_cmd_tx_cb+0x220/0x240
[ 38.976831][ C3] ar5523_cmd_tx_cb+0x220/0x240
[ 38.978412][ C3] __usb_hcd_giveback_urb+0x353/0x5b0
[ 38.979755][ C3] usb_hcd_giveback_urb+0x385/0x430
[ 38.981266][ C3] dummy_timer+0x140c/0x34e0
[ 38.982925][ C3] ? notifier_call_chain+0xb5/0x1e0
[ 38.984761][ C3] ? rcu_read_lock_sched_held+0xb/0x60
[ 38.986242][ C3] ? lock_release+0x51c/0x790
[ 38.987323][ C3] ? _raw_read_unlock_irqrestore+0x37/0x70
[ 38.988483][ C3] ? __wake_up_common_lock+0xde/0x130
[ 38.989621][ C3] ? reacquire_held_locks+0x4a0/0x4a0
[ 38.990777][ C3] ? lock_acquire+0x472/0x550
[ 38.991919][ C3] ? rcu_read_lock_sched_held+0xb/0x60
[ 38.993138][ C3] ? lock_acquire+0x472/0x550
[ 38.994890][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 38.996266][ C3] ? do_raw_spin_unlock+0x16f/0x230
[ 38.997670][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 38.999116][ C3] call_timer_fn+0x1a0/0x6a0
[ 39.000668][ C3] ? add_timer_on+0x4a0/0x4a0
[ 39.002137][ C3] ? reacquire_held_locks+0x4a0/0x4a0
[ 39.003809][ C3] ? __next_timer_interrupt+0x226/0x2a0
[ 39.005509][ C3] __run_timers.part.0+0x69a/0xac0
[ 39.007025][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 39.008716][ C3] ? call_timer_fn+0x6a0/0x6a0
[ 39.010254][ C3] ? cpuacct_percpu_seq_show+0x10/0x10
[ 39.011795][ C3] ? kvm_sched_clock_read+0x14/0x40
[ 39.013277][ C3] ? sched_clock_cpu+0x69/0x2b0
[ 39.014724][ C3] run_timer_softirq+0xb6/0x1d0
[ 39.016196][ C3] __do_softirq+0x1d2/0x9be
[ 39.017616][ C3] __irq_exit_rcu+0xeb/0x190
[ 39.019004][ C3] irq_exit_rcu+0x5/0x20
[ 39.020361][ C3] sysvec_apic_timer_interrupt+0x8f/0xb0
[ 39.021965][ C3] </IRQ>
[ 39.023237][ C3] <TASK>
In ar5523_probe(), ar5523_host_available() calls ar5523_cmd() as below
(there are other functions which finally call ar5523_cmd()):
ar5523_probe()
-> ar5523_host_available()
-> ar5523_cmd_read()
-> ar5523_cmd()
If ar5523_cmd() timed out, then ar5523_host_available() failed and
ar5523_probe() freed the device structure. So, ar5523_cmd_tx_cb()
might touch the freed structure.
This patch fixes this issue by canceling in-flight tx cmd if submitted
urb timed out. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/rtas: avoid device tree lookups in rtas_os_term()
rtas_os_term() is called during panic. Its behavior depends on a couple
of conditions in the /rtas node of the device tree, the traversal of
which entails locking and local IRQ state changes. If the kernel panics
while devtree_lock is held, rtas_os_term() as currently written could
hang.
Instead of discovering the relevant characteristics at panic time,
cache them in file-static variables at boot. Note the lookup for
"ibm,extended-os-term" is converted to of_property_read_bool() since it
is a boolean property, not an RTAS function token.
[mpe: Incorporate suggested change from Nick] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix pci device refcount leak
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from amdgpu_device_resume|suspend_display_audio(),
pci_dev_put() is called to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/apic: Don't disable x2APIC if locked
The APIC supports two modes, legacy APIC (or xAPIC), and Extended APIC
(or x2APIC). X2APIC mode is mostly compatible with legacy APIC, but
it disables the memory-mapped APIC interface in favor of one that uses
MSRs. The APIC mode is controlled by the EXT bit in the APIC MSR.
The MMIO/xAPIC interface has some problems, most notably the APIC LEAK
[1]. This bug allows an attacker to use the APIC MMIO interface to
extract data from the SGX enclave.
Introduce support for a new feature that will allow the BIOS to lock
the APIC in x2APIC mode. If the APIC is locked in x2APIC mode and the
kernel tries to disable the APIC or revert to legacy APIC mode a GP
fault will occur.
Introduce support for a new MSR (IA32_XAPIC_DISABLE_STATUS) and handle
the new locked mode when the LEGACY_XAPIC_DISABLED bit is set by
preventing the kernel from trying to disable the x2APIC.
On platforms with the IA32_XAPIC_DISABLE_STATUS MSR, if SGX or TDX are
enabled the LEGACY_XAPIC_DISABLED will be set by the BIOS. If
legacy APIC is required, then it SGX and TDX need to be disabled in the
BIOS.
[1]: https://aepicleak.com/aepicleak.pdf |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: qcom-adm: fix wrong calling convention for prep_slave_sg
The calling convention for pre_slave_sg is to return NULL on error and
provide an error log to the system. Qcom-adm instead provide error
pointer when an error occur. This indirectly cause kernel panic for
example for the nandc driver that checks only if the pointer returned by
device_prep_slave_sg is not NULL. Returning an error pointer makes nandc
think the device_prep_slave_sg function correctly completed and makes
the kernel panics later in the code.
While nandc is the one that makes the kernel crash, it was pointed out
that the real problem is qcom-adm not following calling convention for
that function.
To fix this, drop returning error pointer and return NULL with an error
log. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix missing unmap if z_erofs_get_extent_compressedlen() fails
Otherwise, meta buffers could be leaked. |
