| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_ct: bail out on template ct in get eval
I noticed this issue while looking at a historic syzbot report [1].
A rule like the one below is enough to trigger the bug:
table ip t {
chain pre {
type filter hook prerouting priority raw;
ct zone set 1
ct original saddr 1.2.3.4 accept
}
}
The first expression attaches a per-cpu template ct via
nft_ct_set_zone_eval() (nf_ct_tmpl_alloc -> kzalloc, tuple is all
zero, nf_ct_l3num(ct) == 0). The next expression then calls
nft_ct_get_eval() on the same skb, treats the template as a real ct
and hits the 16-byte memcpy path. With dreg at NFT_REG32_15 this
overflows past struct nft_regs on the kernel stack; with smaller
dreg values it silently clobbers adjacent registers.
Reject template ct at the eval entry and in nft_ct_get_fast_eval(),
mirroring the check nft_ct_set_eval() already has. Additionally,
bound the address copy in NFT_CT_SRC / NFT_CT_DST by priv->len
instead of by nf_ct_l3num(ct): nf_ct_get_tuple() zeroes the tuple
before pkt_to_tuple() fills in only the protocol-relevant leading
bytes, so the trailing bytes of tuple->{src,dst}.u3.all are
well-defined zero. priv->len is validated at rule load, so the
copy size is now bounded by the destination register rather than
by an untrusted field on the conntrack.
[1]: https://syzkaller.appspot.com/bug?id=389cf09cb72926114fce90dc85a2c3231dcb647c |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: errata: Mitigate TLBI errata on various Arm CPUs
A number of CPUs developed by Arm suffer from errata whereby a broadcast
TLBI;DSB sequence may complete before the global observation of writes
which are translated by an affected TLB entry.
These errata ONLY affect the completion of memory accesses which have
been translated by an invalidated TLB entry, and these errata DO NOT
affect the actual invalidation of TLB entries. TLB entries are removed
correctly.
This issue has been assigned CVE ID CVE-2025-10263.
To mitigate this issue, Arm recommends that software follows any
affected TLBI;DSB sequence with an additional TLBI;DSB, which will
ensure that all memory write effects affected by the first TLBI have
been globally observed. The additional TLBI can use any operation that
is broadcast to affected CPUs, and the additional DSB can use any option
that is sufficient to complete the additional TLBI.
The ARM64_WORKAROUND_REPEAT_TLBI workaround is sufficient to mitigate
the issue. Enable this workaround for affected CPUs, and update the
silicon errata documentation accordingly.
Note that due to the manner in which Arm develops IP and tracks errata,
some CPUs share a common erratum number. |
| In the Linux kernel, the following vulnerability has been resolved:
tap: free page on error paths in tap_get_user_xdp()
tap_get_user_xdp() rejects a frame shorter than ETH_HLEN with -EINVAL,
and returns -ENOMEM when build_skb() fails. Both paths jump to the err
label without freeing the page that vhost_net_build_xdp() allocated for
the frame. tap_sendmsg() discards the per-buffer return value and always
returns 0, so vhost_tx_batch() takes the success path and never frees
the page; each rejected frame in a batch leaks one page-frag chunk.
Free the page on both error paths, before the skb is built. This is the
tap counterpart of the same leak in tun_xdp_one(). |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: diag: reject stale associations in dump_one path
The SCTP exact sock_diag lookup can hold a transport reference, block on
lock_sock(sk), and then resume after sctp_association_free() has marked
the association dead and freed its bind address list.
When that happens, inet_assoc_attr_size() and
inet_diag_msg_sctpasoc_fill() can still dereference association state
that is no longer valid for reporting. In particular,
inet_diag_msg_sctpasoc_fill() may read an empty bind-address list as a
real sctp_sockaddr_entry and trigger an out-of-bounds read from
unrelated association memory.
Reject the association after taking the socket lock if it has been
reaped or detached from the endpoint, and report the lookup as stale.
This keeps the exact dump-one path from formatting torn association
state. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix UAF due to concurrent consumption of ttrace lists in alloc_bulk
Syzkaller repeatedly triggered UAF splats related to nodes in
waiting_for_gp_ttrace within the bpf memalloc:
BUG: KASAN: slab-use-after-free in llist_del_first+0x85/0x110 lib/llist.c:61
Read of size 8 at addr ffff8881572cd080 by task syz.4.470/5112
...
llist_del_first+0x85/0x110 lib/llist.c:61
alloc_bulk+0x193/0x460 kernel/bpf/memalloc.c:229
bpf_mem_refill+0x386/0x560 kernel/bpf/memalloc.c:436
Freed by task 14:
...
__free_rcu kernel/bpf/memalloc.c:281 [inline]
__free_rcu_tasks_trace+0x48/0xd0 kernel/bpf/memalloc.c:291
rcu_tasks_invoke_cbs+0x1ec/0x3e0 kernel/rcu/tasks.h:571
rcu_tasks_one_gp+0x13d/0x220 kernel/rcu/tasks.h:621
rcu_tasks_kthread+0xf3/0x120 kernel/rcu/tasks.h:651
The reason is that the UAF occurs after the RCU Tasks Trace GP expires:
when the __free_rcu() callback runs, there is no synchronization
protecting llist_del_all() against concurrent alloc_bulk() operating on
waiting_for_gp_ttrace, leading to the race condition below:
CPU0 CPU1
__free_rcu (RCU Tasks Trace callback)
alloc_bulk
llist_del_first(&c->waiting_for_gp_ttrace)
entry = smp_load_acquire(&head->first);
do {
if (entry == NULL)
return NULL;
free_all(llist_del_all(&c->waiting_for_gp_ttrace))
llist_for_each_safe(pos, t, llnode)
free_one(pos);
next = READ_ONCE(entry->next); <-- trigger UAF
} while (!try_cmpxchg(&head->first, &entry, next));
In addition, there is also a theoretical race condition on the
free_by_rcu_ttrace list. This race requires two preconditions: an
in-flight Tasks Trace GP keeping c->call_rcu_ttrace_in_progress == 1,
and concurrent cross-CPU frees repopulating c->free_by_rcu_ttrace with
new nodes. Under these conditions, the following scenario triggers UAF:
// CPU0
// irq work is still busy (on PREEMPT_RT)
alloc_bulk()
llist_del_first(&c->free_by_rcu_ttrace)
entry = smp_load_acquire(&head->first);
do {
if (entry == NULL)
return NULL;
// CPU1
bpf_mem_alloc_destroy()
WRITE_ONCE(c->draining, true)
// wait for CPU0
irq_work_sync()
// CPU2
do_call_rcu_ttrace(tgt(CPU0))
if (c->draining) {
llist_del_all(&c->free_by_rcu_ttrace)
free_all()
}
// CPU0 continue
next = READ_ONCE(entry->next); <-- trigger UAF
while (!try_cmpxchg(&head->first, &entry, next));
Fix this by introducing a raw spinlock to synchronize the concurrent
consumption on waiting_for_gp_ttrace and free_by_rcu_ttrace. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: fix object leak when drm_gem_handle_create() fails
virtio_gpu_gem_create() owns the reference taken by
virtio_gpu_object_create(). On the drm_gem_handle_create() error path it
calls drm_gem_object_release() instead of dropping that reference.
drm_gem_object_release() is the inverse of drm_gem_object_init() and does
not touch the reference count or call obj->funcs->free(), so it is only
correct as the last step of a destructor, as in
virtio_gpu_cleanup_object(). Using it here leaves the bo at refcount 1
with no remaining reference, so virtio_gpu_free_object() never runs and
the shmem pages, sg table and virtio_gpu_object are leaked. Since
virtio_gpu_object_create() has already set bo->created,
VIRTIO_GPU_CMD_RESOURCE_UNREF is not queued either, leaking the host-side
resource and the resource id.
drm_gem_handle_create_tail() drops the handle reference on all of its
internal error paths, so the caller only has to drop its own. Use
drm_gem_object_put(), matching the success path below. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: Add preempt_{disable,enable}_nested() in reqsk_queue_hash_req().
syzbot reported a weird reqsk->rsk_refcnt underflow in
__inet_csk_reqsk_queue_drop().
The captured reqsk_put() in __inet_csk_reqsk_queue_drop()
is called only when it successfully removes reqsk from ehash.
Moreover, reqsk_timer_handler() calls another reqsk_put()
after that.
This indicates that the reqsk was missing both refcnts for
ehash and the timer itself.
Since all the syzbot reports had PREEMPT_RT enabled, the only
possible scenario is that reqsk_queue_hash_req() is preempted
after mod_timer() and before refcount_set(), and then the timer
triggered after 1s aborts the reqsk due to its listener's close().
Let's wrap mod_timer() and refcount_set() with
preempt_disable_nested() and preempt_enable_nested().
Note that inet_ehash_insert() holds the normal spin_lock()
(mutex in PREEMPT_RT), so it must be called outside of
preempt_disable_nested(), but this is fine.
The lookup path just ignores 0 sk_refcnt entries in ehash
and tries to create another reqsk, but this will fail at
inet_ehash_insert().
[0]:
refcount_t: underflow; use-after-free.
WARNING: lib/refcount.c:28 at refcount_warn_saturate+0xb2/0x110 lib/refcount.c:28, CPU#0: ktimers/0/16
Modules linked in:
CPU: 0 UID: 0 PID: 16 Comm: ktimers/0 Tainted: G L syzkaller #0 PREEMPT_{RT,(full)}
Tainted: [L]=SOFTLOCKUP
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/18/2026
RIP: 0010:refcount_warn_saturate+0xb2/0x110 lib/refcount.c:28
Code: e4 7d d1 0a 67 48 0f b9 3a eb 4a e8 38 3d 23 fd 48 8d 3d e1 7d d1 0a 67 48 0f b9 3a eb 37 e8 25 3d 23 fd 48 8d 3d de 7d d1 0a <67> 48 0f b9 3a eb 24 e8 12 3d 23 fd 48 8d 3d db 7d d1 0a 67 48 0f
RSP: 0000:ffffc90000157948 EFLAGS: 00010246
RAX: ffffffff84a1301b RBX: 0000000000000003 RCX: ffff88801ca98000
RDX: 0000000000000100 RSI: 0000000000000000 RDI: ffffffff8f72ae00
RBP: ffffffff99ae3b01 R08: ffff88801ca98000 R09: 0000000000000005
R10: 0000000000000100 R11: 0000000000000004 R12: ffff8880425ef568
R13: ffff8880425ef4f8 R14: ffff8880425ef578 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff888126386000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f7b46710e9c CR3: 000000000dbb6000 CR4: 00000000003526f0
Call Trace:
<TASK>
__refcount_sub_and_test include/linux/refcount.h:400 [inline]
__refcount_dec_and_test include/linux/refcount.h:432 [inline]
refcount_dec_and_test include/linux/refcount.h:450 [inline]
reqsk_put include/net/request_sock.h:136 [inline]
__inet_csk_reqsk_queue_drop+0x3ce/0x440 net/ipv4/inet_connection_sock.c:1007
reqsk_timer_handler+0x651/0xdf0 net/ipv4/inet_connection_sock.c:1137
call_timer_fn+0x192/0x5e0 kernel/time/timer.c:1748
expire_timers kernel/time/timer.c:1799 [inline]
__run_timers kernel/time/timer.c:2374 [inline]
__run_timer_base+0x6a3/0x9f0 kernel/time/timer.c:2386
run_timer_base kernel/time/timer.c:2395 [inline]
run_timer_softirq+0x67/0x170 kernel/time/timer.c:2403
handle_softirqs+0x1de/0x6d0 kernel/softirq.c:622
__do_softirq kernel/softirq.c:656 [inline]
run_ktimerd+0x69/0x100 kernel/softirq.c:1151
smpboot_thread_fn+0x541/0xa50 kernel/smpboot.c:160
kthread+0x388/0x470 kernel/kthread.c:436
ret_from_fork+0x514/0xb70 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK> |
| Improper certificate validation in Active Directory Federation Services (AD FS) allows an unauthorized attacker to perform spoofing over a network. |
| In the Linux kernel, the following vulnerability has been resolved:
ip6_vti: fix incorrect tunnel matching in vti6_tnl_lookup()
In vti6_tnl_lookup(), when an exact match for a tunnel fails,
the code falls back to searching for wildcard tunnels:
- Tunnels matching the packet's local address, with any remote address
wildcard remote).
- Tunnels matching the packet's remote address, with any local address
(wildcard local).
However, vti6 stores all these different types of tunnels in the same
hash table (ip6n->tnls_r_l) prone to hash collisions.
The bug is that the fallback search loops in vti6_tnl_lookup() were
missing checks to ensure that the candidate tunnel actually has
a wildcard address. |
| In the Linux kernel, the following vulnerability has been resolved:
ip6_vti: set netns_immutable on the fallback device.
john1988 and Noam Rathaus reported that vti6_init_net() does not set the
netns_immutable flag on the per-netns fallback tunnel device (ip6_vti0).
Other similar tunnel drivers (like ip6_tunnel, sit, ip6_gre, and ip_tunnel)
correctly set this flag during their fallback device initialization to
prevent them from being moved to another network namespace. |
| In the Linux kernel, the following vulnerability has been resolved:
inet: RAW sockets using IPPROTO_RAW MUST drop incoming ICMP
Yizhou Zhao reported that simply having one RAW socket on protocol
IPPROTO_RAW (255) was dangerous.
socket(AF_INET, SOCK_RAW, 255);
A malicious incoming ICMP packet can set the protocol field to 255
and match this socket, leading to FNHE cache changes.
inner = IP(src="192.168.2.1", dst="8.8.8.8", proto=255)/Raw("TEST")
pkt = IP(src="192.168.1.1", dst="192.168.2.1")/ICMP(type=3, code=4, nexthopmtu=576)/inner
"man 7 raw" states:
A protocol of IPPROTO_RAW implies enabled IP_HDRINCL and is able
to send any IP protocol that is specified in the passed header.
Receiving of all IP protocols via IPPROTO_RAW is not possible
using raw sockets.
Make sure we drop these malicious packets. |
| In the Linux kernel, the following vulnerability has been resolved:
tun: free page on build_skb failure in tun_xdp_one()
When build_skb() fails in tun_xdp_one(), the function sets ret to
-ENOMEM and jumps to the out label, which returns without freeing the
page that vhost_net_build_xdp() allocated for the frame. As with the
short-frame rejection path, tun_sendmsg() discards the per-buffer error
and still returns total_len, so vhost_tx_batch() takes the success path
and never frees the page. Each build_skb() failure in a batch leaks one
page-frag chunk.
Free the page before taking the error path, matching the put_page() the
other error exits of tun_xdp_one() already perform. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: validate checksum_start before completing checksum
If a packet with bad checksum metadata gets into the ipv4 stack,
skb_checksum_help can corrupt the network header and cause a bunch of
mischief.
This was discovered and reported by Paulos, and has been reporoduced
by others independently since.
We really shouldn't allow such packets in, but as a defence
in depth measure, let's also check before we complete the checksum.
A more complete validation at input is forthcoming, but needs more work. |
| In the Linux kernel, the following vulnerability has been resolved:
dm thin metadata: fix metadata snapshot consistency on commit failure
__reserve_metadata_snap() and __release_metadata_snap() modify the
superblock's held_root directly in the block_manager's buffer. If the
subsequent metadata commit fails, the held_root gets flushed to disk
through the abort_transaction path, resulting in inconsistent metadata.
Reproducer 1: __reserve_metadata_snap()
1. Create a 2 MiB metadata device and make the region after the 14th
block inaccessible, to trigger metadata commit failure in the
subsequent reserve_metadata_snap operation. The 14th block will be
the shadow destination for the index block.
dmsetup create tmeta --table "0 112 linear /dev/sdc 0
112 3984 error"
2. Create a 16 MiB thin-pool
dmsetup create tdata --table "0 32768 zero"
dd if=/dev/zero of=/dev/mapper/tmeta bs=4k count=1
dmsetup create tpool --table "0 32768 thin-pool /dev/mapper/tmeta \
/dev/mapper/tdata 128 0 1 skip_block_zeroing"
3. Take a metadata snapshot to trigger metadata commit failure and
transaction abort. However, the held_root is written to disk,
breaking metadata consistency.
dmsetup message tpool 0 "reserve_metadata_snap"
thin_check v1.2.2 result:
Bad reference count for metadata block 6. Expected 2, but space map contains 1.
Bad reference count for metadata block 7. Expected 2, but space map contains 1.
Bad reference count for metadata block 13. Expected 1, but space map contains 0.
Reproducer 2: __release_metadata_snap()
1. Create a 2 MiB metadata device and make the region after the 16th
block inaccessible, to trigger metadata commit failure in the
subsequent release_metadata_snap operation. The 16th block will be
the shadow destination for the index block.
dmsetup create tmeta --table "0 128 linear /dev/sdc 0
128 3968 error"
2. Create a 16 MiB thin-pool
dmsetup create tdata --table "0 32768 zero"
dd if=/dev/zero of=/dev/mapper/tmeta bs=4k count=1
dmsetup create tpool --table "0 32768 thin-pool /dev/mapper/tmeta \
/dev/mapper/tdata 128 0 1 skip_block_zeroing"
3. Reserve then release the metadata snapshot, to trigger metadata
commit failure and transaction abort. The held_root gets removed
from the on-disk superblock, causing inconsistent metadata.
dmsetup message tpool 0 "reserve_metadata_snap"
dmsetup message tpool 0 "release_metadata_snap"
thin_check v1.2.2 result:
Bad reference count for metadata block 6. Expected 1, but space map contains 2.
Bad reference count for metadata block 7. Expected 1, but space map contains 2.
1 metadata blocks have leaked.
Fix by deferring the held_root update to commit time.
Additionally, move the existing-snapshot check in __reserve_metadata_snap
before the shadow operation to avoid unnecessary work. In
__release_metadata_snap, clear pmd->held_root before btree deletion so
partial failure leaks blocks rather than leaving a stale reference, and
unlock the snapshot block before decrementing its refcount. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: avoid leaking the caller's thread keyring via the table device file
The refactoring in commit a28d893eb327 ("md: port block device access to file")
accidentally causes the caller's thread keyring to be kept alive long
beyond the caller's lifetime.
As a result, "cryptsetup luksSuspend" silently fails to wipe the
LUKS volume key from memory.
In detail: "cryptsetup luksOpen" uses its supposedly ephemeral thread
keyring to pass the volume key to the kernel. dm-crypt's
crypt_set_keyring_key() copies the key material into its own
crypt_config structure and then drops its own reference to the key in
the keyring with key_put().
With this fix, restoring pre-v6.9 behavior, the copy in the thread
keyring is then promptly garbage collected, such that exactly one copy
of the volume key remains. This single copy is correctly wiped from
memory on "cryptsetup luksSuspend".
Without this fix, the thread keyring and the volume key in it remains.
This second copy is only freed on "luksClose". "luksSuspend" neither
knows about this copy nor has any way to remove it, so the key remains
recoverable from RAM after a suspend that is documented to have wiped it.
This fix should not introduce new security problems, as the code is
anyway gated by CAP_SYS_ADMIN. The device-mapper core, not the calling
task, is the legitimate owner of this long-lived file. |
| In the Linux kernel, the following vulnerability has been resolved:
dm_early_create: fix freeing used table on dm_resume failure
If dm_resume fails, the kernel attempts to free table with
dm_table_destroy, but the table was already instantiated with
dm_swap_table. This commit skips the call to dm_table_destroy in this
case. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-integrity: fix a bug if the bio is out of limits
If dm_integrity_check_limits fails, the code would exit with
DM_MAPIO_KILL. However, the range would be already locked at this point,
and it wouldn't be unlocked, resulting in a deadlock. Let's move the
limit check up, so that when it exits, no resources are leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-integrity: don't increment hash_offset twice
hash_offset is already incremented in the loop "for (i = 0; i < to_copy;
i++, ts--)". Do not increment it again. |
| In the Linux kernel, the following vulnerability has been resolved:
dma-fence: Make dma_fence_dedup_array() robust against 0-count input
dma_fence_dedup_array() returns 1 when called with num_fences == 0:
the for-loop body never executes, j stays at 0, and the final
`return ++j` yields 1. This contradicts both the kernel-doc ("Return:
Number of unique fences remaining in the array") and the natural
expectation that 0 input gives 0 output.
The caller __dma_fence_unwrap_merge() bails out via the
`if (count == 0 || count == 1)` fast path and so is save.
But amdgpu_userq_wait_*() could reach the dedup call with a zero local
count and dereference an uninitialized fence slot in the array.
Make the contract match the documentation by returning 0 early. This
also skips an unnecessary sort() call on an empty array. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: xen: scsiback: Free unsubmitted command instead of double-putting it
scsiback_get_pend_req() obtains a command tag and returns a vscsibk_pend
whose embedded se_cmd has only been memset to 0, so its cmd_kref is 0;
the se_cmd is initialised (kref_init() via target_init_cmd()) only
later, in scsiback_cmd_exec(), on the successful VSCSIIF_ACT_SCSI_CDB
path. The two error paths in scsiback_do_cmd_fn() taken before the
command is submitted -- a failed scsiback_gnttab_data_map() and an
unknown ring_req.act -- call
transport_generic_free_cmd(&pending_req->se_cmd, 0), which kref_put()s a
refcount of 0. That underflows it ("refcount_t: underflow;
use-after-free") and, as the release function is not run, leaks the
command tag.
Impact: a pvSCSI guest can leak every command tag of a LUN's session,
stopping the LUN, by submitting requests with a bad grant reference or
an unknown request type; under panic_on_warn the refcount underflow
panics the host.
Add a helper that just returns the tag with target_free_tag() and sends
the error response. It frees the tag while the v2p reference still pins
the session, and snapshots the response fields beforehand because
freeing the tag can let another ring reuse the pending_req slot. |
