| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: vxlan: prevent NULL deref in vxlan_xmit_one
Neither sock4 nor sock6 pointers are guaranteed to be non-NULL in
vxlan_xmit_one, e.g. if the iface is brought down. This can lead to the
following NULL dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000010
Oops: Oops: 0000 [#1] SMP NOPTI
RIP: 0010:vxlan_xmit_one+0xbb3/0x1580
Call Trace:
vxlan_xmit+0x429/0x610
dev_hard_start_xmit+0x55/0xa0
__dev_queue_xmit+0x6d0/0x7f0
ip_finish_output2+0x24b/0x590
ip_output+0x63/0x110
Mentioned commits changed the code path in vxlan_xmit_one and as a side
effect the sock4/6 pointer validity checks in vxlan(6)_get_route were
lost. Fix this by adding back checks.
Since both commits being fixed were released in the same version (v6.7)
and are strongly related, bundle the fixes in a single commit. |
| In the Linux kernel, the following vulnerability has been resolved:
mlx5: Fix default values in create CQ
Currently, CQs without a completion function are assigned the
mlx5_add_cq_to_tasklet function by default. This is problematic since
only user CQs created through the mlx5_ib driver are intended to use
this function.
Additionally, all CQs that will use doorbells instead of polling for
completions must call mlx5_cq_arm. However, the default CQ creation flow
leaves a valid value in the CQ's arm_db field, allowing FW to send
interrupts to polling-only CQs in certain corner cases.
These two factors would allow a polling-only kernel CQ to be triggered
by an EQ interrupt and call a completion function intended only for user
CQs, causing a null pointer exception.
Some areas in the driver have prevented this issue with one-off fixes
but did not address the root cause.
This patch fixes the described issue by adding defaults to the create CQ
flow. It adds a default dummy completion function to protect against
null pointer exceptions, and it sets an invalid command sequence number
by default in kernel CQs to prevent the FW from sending an interrupt to
the CQ until it is armed. User CQs are responsible for their own
initialization values.
Callers of mlx5_core_create_cq are responsible for changing the
completion function and arming the CQ per their needs. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: use dst_dev_rcu() in tcp_fastopen_active_disable_ofo_check()
Use RCU to avoid a pair of atomic operations and a potential
UAF on dst_dev()->flags. |
| In the Linux kernel, the following vulnerability has been resolved:
media: nxp: imx8-isi: Fix streaming cleanup on release
The current implementation unconditionally calls
mxc_isi_video_cleanup_streaming() in mxc_isi_video_release(). This can
lead to situations where any release call (like from a simple
"v4l2-ctl -l") may release a currently streaming queue when called on
such a device.
This is reproducible on an i.MX8MP board by streaming from an ISI
capture device using gstreamer:
gst-launch-1.0 -v v4l2src device=/dev/videoX ! \
video/x-raw,format=GRAY8,width=1280,height=800,framerate=1/120 ! \
fakesink
While this stream is running, querying the caps of the same device
provokes the error state:
v4l2-ctl -l -d /dev/videoX
This results in the following trace:
[ 155.452152] ------------[ cut here ]------------
[ 155.452163] WARNING: CPU: 0 PID: 1708 at drivers/media/platform/nxp/imx8-isi/imx8-isi-pipe.c:713 mxc_isi_pipe_irq_handler+0x19c/0x1b0 [imx8_isi]
[ 157.004248] Modules linked in: cfg80211 rpmsg_ctrl rpmsg_char rpmsg_tty virtio_rpmsg_bus rpmsg_ns rpmsg_core rfkill nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables mcp251x6
[ 157.053499] CPU: 0 UID: 0 PID: 1708 Comm: python3 Not tainted 6.15.4-00114-g1f61ca5cad76 #1 PREEMPT
[ 157.064369] Hardware name: imx8mp_board_01 (DT)
[ 157.068205] pstate: 400000c5 (nZcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 157.075169] pc : mxc_isi_pipe_irq_handler+0x19c/0x1b0 [imx8_isi]
[ 157.081195] lr : mxc_isi_pipe_irq_handler+0x38/0x1b0 [imx8_isi]
[ 157.087126] sp : ffff800080003ee0
[ 157.090438] x29: ffff800080003ee0 x28: ffff0000c3688000 x27: 0000000000000000
[ 157.097580] x26: 0000000000000000 x25: ffff0000c1e7ac00 x24: ffff800081b5ad50
[ 157.104723] x23: 00000000000000d1 x22: 0000000000000000 x21: ffff0000c25e4000
[ 157.111866] x20: 0000000060000200 x19: ffff80007a0608d0 x18: 0000000000000000
[ 157.119008] x17: ffff80006a4e3000 x16: ffff800080000000 x15: 0000000000000000
[ 157.126146] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
[ 157.133287] x11: 0000000000000040 x10: ffff0000c01445f0 x9 : ffff80007a053a38
[ 157.140425] x8 : ffff0000c04004b8 x7 : 0000000000000000 x6 : 0000000000000000
[ 157.147567] x5 : ffff0000c0400490 x4 : ffff80006a4e3000 x3 : ffff0000c25e4000
[ 157.154706] x2 : 0000000000000000 x1 : ffff8000825c0014 x0 : 0000000060000200
[ 157.161850] Call trace:
[ 157.164296] mxc_isi_pipe_irq_handler+0x19c/0x1b0 [imx8_isi] (P)
[ 157.170319] __handle_irq_event_percpu+0x58/0x218
[ 157.175029] handle_irq_event+0x54/0xb8
[ 157.178867] handle_fasteoi_irq+0xac/0x248
[ 157.182968] handle_irq_desc+0x48/0x68
[ 157.186723] generic_handle_domain_irq+0x24/0x38
[ 157.191346] gic_handle_irq+0x54/0x120
[ 157.195098] call_on_irq_stack+0x24/0x30
[ 157.199027] do_interrupt_handler+0x88/0x98
[ 157.203212] el0_interrupt+0x44/0xc0
[ 157.206792] __el0_irq_handler_common+0x18/0x28
[ 157.211328] el0t_64_irq_handler+0x10/0x20
[ 157.215429] el0t_64_irq+0x198/0x1a0
[ 157.219009] ---[ end trace 0000000000000000 ]---
Address this issue by moving the streaming preparation and cleanup to
the vb2 .prepare_streaming() and .unprepare_streaming() operations. This
also simplifies the driver by allowing direct usage of the
vb2_ioctl_streamon() and vb2_ioctl_streamoff() helpers, and removal of
the manual cleanup from mxc_isi_video_release(). |
| In the Linux kernel, the following vulnerability has been resolved:
amd/amdkfd: enhance kfd process check in switch partition
current switch partition only check if kfd_processes_table is empty.
kfd_prcesses_table entry is deleted in kfd_process_notifier_release, but
kfd_process tear down is in kfd_process_wq_release.
consider two processes:
Process A (workqueue) -> kfd_process_wq_release -> Access kfd_node member
Process B switch partition -> amdgpu_xcp_pre_partition_switch -> amdgpu_amdkfd_device_fini_sw
-> kfd_node tear down.
Process A and B may trigger a race as shown in dmesg log.
This patch is to resolve the race by adding an atomic kfd_process counter
kfd_processes_count, it increment as create kfd process, decrement as
finish kfd_process_wq_release.
v2: Put kfd_processes_count per kfd_dev, move decrement to kfd_process_destroy_pdds
and bug fix. (Philip Yang)
[3966658.307702] divide error: 0000 [#1] SMP NOPTI
[3966658.350818] i10nm_edac
[3966658.356318] CPU: 124 PID: 38435 Comm: kworker/124:0 Kdump: loaded Tainted
[3966658.356890] Workqueue: kfd_process_wq kfd_process_wq_release [amdgpu]
[3966658.362839] nfit
[3966658.366457] RIP: 0010:kfd_get_num_sdma_engines+0x17/0x40 [amdgpu]
[3966658.366460] Code: 00 00 e9 ac 81 02 00 66 66 2e 0f 1f 84 00 00 00 00 00 90 0f 1f 44 00 00 48 8b 4f 08 48 8b b7 00 01 00 00 8b 81 58 26 03 00 99 <f7> be b8 01 00 00 80 b9 70 2e 00 00 00 74 0b 83 f8 02 ba 02 00 00
[3966658.380967] x86_pkg_temp_thermal
[3966658.391529] RSP: 0018:ffffc900a0edfdd8 EFLAGS: 00010246
[3966658.391531] RAX: 0000000000000008 RBX: ffff8974e593b800 RCX: ffff888645900000
[3966658.391531] RDX: 0000000000000000 RSI: ffff888129154400 RDI: ffff888129151c00
[3966658.391532] RBP: ffff8883ad79d400 R08: 0000000000000000 R09: ffff8890d2750af4
[3966658.391532] R10: 0000000000000018 R11: 0000000000000018 R12: 0000000000000000
[3966658.391533] R13: ffff8883ad79d400 R14: ffffe87ff662ba00 R15: ffff8974e593b800
[3966658.391533] FS: 0000000000000000(0000) GS:ffff88fe7f600000(0000) knlGS:0000000000000000
[3966658.391534] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[3966658.391534] CR2: 0000000000d71000 CR3: 000000dd0e970004 CR4: 0000000002770ee0
[3966658.391535] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[3966658.391535] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
[3966658.391536] PKRU: 55555554
[3966658.391536] Call Trace:
[3966658.391674] deallocate_sdma_queue+0x38/0xa0 [amdgpu]
[3966658.391762] process_termination_cpsch+0x1ed/0x480 [amdgpu]
[3966658.399754] intel_powerclamp
[3966658.402831] kfd_process_dequeue_from_all_devices+0x5b/0xc0 [amdgpu]
[3966658.402908] kfd_process_wq_release+0x1a/0x1a0 [amdgpu]
[3966658.410516] coretemp
[3966658.434016] process_one_work+0x1ad/0x380
[3966658.434021] worker_thread+0x49/0x310
[3966658.438963] kvm_intel
[3966658.446041] ? process_one_work+0x380/0x380
[3966658.446045] kthread+0x118/0x140
[3966658.446047] ? __kthread_bind_mask+0x60/0x60
[3966658.446050] ret_from_fork+0x1f/0x30
[3966658.446053] Modules linked in: kpatch_20765354(OEK)
[3966658.455310] kvm
[3966658.464534] mptcp_diag xsk_diag raw_diag unix_diag af_packet_diag netlink_diag udp_diag act_pedit act_mirred act_vlan cls_flower kpatch_21951273(OEK) kpatch_18424469(OEK) kpatch_19749756(OEK)
[3966658.473462] idxd_mdev
[3966658.482306] kpatch_17971294(OEK) sch_ingress xt_conntrack amdgpu(OE) amdxcp(OE) amddrm_buddy(OE) amd_sched(OE) amdttm(OE) amdkcl(OE) intel_ifs iptable_mangle tcm_loop target_core_pscsi tcp_diag target_core_file inet_diag target_core_iblock target_core_user target_core_mod coldpgs kpatch_18383292(OEK) ip6table_nat ip6table_filter ip6_tables ip_set_hash_ipportip ip_set_hash_ipportnet ip_set_hash_ipport ip_set_bitmap_port xt_comment iptable_nat nf_nat iptable_filter ip_tables ip_set ip_vs_sh ip_vs_wrr ip_vs_rr ip_vs nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 sn_core_odd(OE) i40e overlay binfmt_misc tun bonding(OE) aisqos(OE) aisqo
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: Intel: avs: Do not share the name pointer between components
By sharing 'name' directly, tearing down components may lead to
use-after-free errors. Duplicate the name to avoid that.
At the same time, update the order of operations - since commit
cee28113db17 ("ASoC: dmaengine_pcm: Allow passing component name via
config") the framework does not override component->name if set before
invoking the initializer. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: fix crash in set_mesh_sync and set_mesh_complete
There is a BUG: KASAN: stack-out-of-bounds in set_mesh_sync due to
memcpy from badly declared on-stack flexible array.
Another crash is in set_mesh_complete() due to double list_del via
mgmt_pending_valid + mgmt_pending_remove.
Use DEFINE_FLEX to declare the flexible array right, and don't memcpy
outside bounds.
As mgmt_pending_valid removes the cmd from list, use mgmt_pending_free,
and also report status on error. |
| In the Linux kernel, the following vulnerability has been resolved:
net: use dst_dev_rcu() in sk_setup_caps()
Use RCU to protect accesses to dst->dev from sk_setup_caps()
and sk_dst_gso_max_size().
Also use dst_dev_rcu() in ip6_dst_mtu_maybe_forward(),
and ip_dst_mtu_maybe_forward().
ip4_dst_hoplimit() can use dst_dev_net_rcu(). |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: use RCU in ip6_output()
Use RCU in ip6_output() in order to use dst_dev_rcu() to prevent
possible UAF.
We can remove rcu_read_lock()/rcu_read_unlock() pairs
from ip6_finish_output2(). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Fix data race in CPU latency PM QoS request handling
The cpu_latency_qos_add/remove/update_request interfaces lack internal
synchronization by design, requiring the caller to ensure thread safety.
The current implementation relies on the 'pm_qos_enabled' flag, which is
insufficient to prevent concurrent access and cannot serve as a proper
synchronization mechanism. This has led to data races and list
corruption issues.
A typical race condition call trace is:
[Thread A]
ufshcd_pm_qos_exit()
--> cpu_latency_qos_remove_request()
--> cpu_latency_qos_apply();
--> pm_qos_update_target()
--> plist_del <--(1) delete plist node
--> memset(req, 0, sizeof(*req));
--> hba->pm_qos_enabled = false;
[Thread B]
ufshcd_devfreq_target
--> ufshcd_devfreq_scale
--> ufshcd_scale_clks
--> ufshcd_pm_qos_update <--(2) pm_qos_enabled is true
--> cpu_latency_qos_update_request
--> pm_qos_update_target
--> plist_del <--(3) plist node use-after-free
Introduces a dedicated mutex to serialize PM QoS operations, preventing
data races and ensuring safe access to PM QoS resources, including sysfs
interface reads. |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: qcom: pas: Shutdown lite ADSP DTB on X1E
The ADSP firmware on X1E has separate firmware binaries for the main
firmware and the DTB. The same applies for the "lite" firmware loaded by
the boot firmware.
When preparing to load the new ADSP firmware we shutdown the lite_pas_id
for the main firmware, but we don't shutdown the corresponding lite pas_id
for the DTB. The fact that we're leaving it "running" forever becomes
obvious if you try to reuse (or just access) the memory region used by the
"lite" firmware: The &adsp_boot_mem is accessible, but accessing the
&adsp_boot_dtb_mem results in a crash.
We don't support reusing the memory regions currently, but nevertheless we
should not keep part of the lite firmware running. Fix this by adding the
lite_dtb_pas_id and shutting it down as well.
We don't have a way to detect if the lite firmware is actually running yet,
so ignore the return status of qcom_scm_pas_shutdown() for now. This was
already the case before, the assignment to "ret" is not used anywhere. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/s390: Make attach succeed when the device was surprise removed
When a PCI device is removed with surprise hotplug, there may still be
attempts to attach the device to the default domain as part of tear down
via (__iommu_release_dma_ownership()), or because the removal happens
during probe (__iommu_probe_device()). In both cases zpci_register_ioat()
fails with a cc value indicating that the device handle is invalid. This
is because the device is no longer part of the instance as far as the
hypervisor is concerned.
Currently this leads to an error return and s390_iommu_attach_device()
fails. This triggers the WARN_ON() in __iommu_group_set_domain_nofail()
because attaching to the default domain must never fail.
With the device fenced by the hypervisor no DMAs to or from memory are
possible and the IOMMU translations have no effect. Proceed as if the
registration was successful and let the hotplug event handling clean up
the device.
This is similar to how devices in the error state are handled since
commit 59bbf596791b ("iommu/s390: Make attach succeed even if the device
is in error state") except that for removal the domain will not be
registered later. This approach was also previously discussed at the
link.
Handle both cases, error state and removal, in a helper which checks if
the error needs to be propagated or ignored. Avoid magic number
condition codes by using the pre-existing, but never used, defines for
PCI load/store condition codes and rename them to reflect that they
apply to all PCI instructions. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: fix race condition validating r_parent before applying state
Add validation to ensure the cached parent directory inode matches the
directory info in MDS replies. This prevents client-side race conditions
where concurrent operations (e.g. rename) cause r_parent to become stale
between request initiation and reply processing, which could lead to
applying state changes to incorrect directory inodes.
[ idryomov: folded a kerneldoc fixup and a follow-up fix from Alex to
move CEPH_CAP_PIN reference when r_parent is updated:
When the parent directory lock is not held, req->r_parent can become
stale and is updated to point to the correct inode. However, the
associated CEPH_CAP_PIN reference was not being adjusted. The
CEPH_CAP_PIN is a reference on an inode that is tracked for
accounting purposes. Moving this pin is important to keep the
accounting balanced. When the pin was not moved from the old parent
to the new one, it created two problems: The reference on the old,
stale parent was never released, causing a reference leak.
A reference for the new parent was never acquired, creating the risk
of a reference underflow later in ceph_mdsc_release_request(). This
patch corrects the logic by releasing the pin from the old parent and
acquiring it for the new parent when r_parent is switched. This
ensures reference accounting stays balanced. ] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: fix list corruption after hardware restart
Since stations are recreated from scratch, all lists that wcids are added
to must be cleared before calling ieee80211_restart_hw.
Set wcid->sta = 0 for each wcid entry in order to ensure that they are
not added again before they are ready. |
| In the Linux kernel, the following vulnerability has been resolved:
ptp: ocp: fix use-after-free bugs causing by ptp_ocp_watchdog
The ptp_ocp_detach() only shuts down the watchdog timer if it is
pending. However, if the timer handler is already running, the
timer_delete_sync() is not called. This leads to race conditions
where the devlink that contains the ptp_ocp is deallocated while
the timer handler is still accessing it, resulting in use-after-free
bugs. The following details one of the race scenarios.
(thread 1) | (thread 2)
ptp_ocp_remove() |
ptp_ocp_detach() | ptp_ocp_watchdog()
if (timer_pending(&bp->watchdog))| bp = timer_container_of()
timer_delete_sync() |
|
devlink_free(devlink) //free |
| bp-> //use
Resolve this by unconditionally calling timer_delete_sync() to ensure
the timer is reliably deactivated, preventing any access after free. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: Fix NPD when refreshing an FDB entry with a nexthop object
VXLAN FDB entries can point to either a remote destination or an FDB
nexthop group. The latter is usually used in EVPN deployments where
learning is disabled.
However, when learning is enabled, an incoming packet might try to
refresh an FDB entry that points to an FDB nexthop group and therefore
does not have a remote. Such packets should be dropped, but they are
only dropped after dereferencing the non-existent remote, resulting in a
NPD [1] which can be reproduced using [2].
Fix by dropping such packets earlier. Remove the misleading comment from
first_remote_rcu().
[1]
BUG: kernel NULL pointer dereference, address: 0000000000000000
[...]
CPU: 13 UID: 0 PID: 361 Comm: mausezahn Not tainted 6.17.0-rc1-virtme-g9f6b606b6b37 #1 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014
RIP: 0010:vxlan_snoop+0x98/0x1e0
[...]
Call Trace:
<TASK>
vxlan_encap_bypass+0x209/0x240
encap_bypass_if_local+0xb1/0x100
vxlan_xmit_one+0x1375/0x17e0
vxlan_xmit+0x6b4/0x15f0
dev_hard_start_xmit+0x5d/0x1c0
__dev_queue_xmit+0x246/0xfd0
packet_sendmsg+0x113a/0x1850
__sock_sendmsg+0x38/0x70
__sys_sendto+0x126/0x180
__x64_sys_sendto+0x24/0x30
do_syscall_64+0xa4/0x260
entry_SYSCALL_64_after_hwframe+0x4b/0x53
[2]
#!/bin/bash
ip address add 192.0.2.1/32 dev lo
ip address add 192.0.2.2/32 dev lo
ip nexthop add id 1 via 192.0.2.3 fdb
ip nexthop add id 10 group 1 fdb
ip link add name vx0 up type vxlan id 10010 local 192.0.2.1 dstport 12345 localbypass
ip link add name vx1 up type vxlan id 10020 local 192.0.2.2 dstport 54321 learning
bridge fdb add 00:11:22:33:44:55 dev vx0 self static dst 192.0.2.2 port 54321 vni 10020
bridge fdb add 00:aa:bb:cc:dd:ee dev vx1 self static nhid 10
mausezahn vx0 -a 00:aa:bb:cc:dd:ee -b 00:11:22:33:44:55 -c 1 -q |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Fix memory corruption when FW resources change during ifdown
bnxt_set_dflt_rings() assumes that it is always called before any TC has
been created. So it doesn't take bp->num_tc into account and assumes
that it is always 0 or 1.
In the FW resource or capability change scenario, the FW will return
flags in bnxt_hwrm_if_change() that will cause the driver to
reinitialize and call bnxt_cancel_reservations(). This will lead to
bnxt_init_dflt_ring_mode() calling bnxt_set_dflt_rings() and bp->num_tc
may be greater than 1. This will cause bp->tx_ring[] to be sized too
small and cause memory corruption in bnxt_alloc_cp_rings().
Fix it by properly scaling the TX rings by bp->num_tc in the code
paths mentioned above. Add 2 helper functions to determine
bp->tx_nr_rings and bp->tx_nr_rings_per_tc. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: x86/aegis - Add missing error checks
The skcipher_walk functions can allocate memory and can fail, so
checking for errors is necessary. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix sleeping-in-atomic in ath11k_mac_op_set_bitrate_mask()
ath11k_mac_disable_peer_fixed_rate() is passed as the iterator to
ieee80211_iterate_stations_atomic(). Note in this case the iterator is
required to be atomic, however ath11k_mac_disable_peer_fixed_rate() does
not follow it as it might sleep. Consequently below warning is seen:
BUG: sleeping function called from invalid context at wmi.c:304
Call Trace:
<TASK>
dump_stack_lvl
__might_resched.cold
ath11k_wmi_cmd_send
ath11k_wmi_set_peer_param
ath11k_mac_disable_peer_fixed_rate
ieee80211_iterate_stations_atomic
ath11k_mac_op_set_bitrate_mask.cold
Change to ieee80211_iterate_stations_mtx() to fix this issue.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: Fix backlog accounting in qdisc_dequeue_internal
This issue applies for the following qdiscs: hhf, fq, fq_codel, and
fq_pie, and occurs in their change handlers when adjusting to the new
limit. The problem is the following in the values passed to the
subsequent qdisc_tree_reduce_backlog call given a tbf parent:
When the tbf parent runs out of tokens, skbs of these qdiscs will
be placed in gso_skb. Their peek handlers are qdisc_peek_dequeued,
which accounts for both qlen and backlog. However, in the case of
qdisc_dequeue_internal, ONLY qlen is accounted for when pulling
from gso_skb. This means that these qdiscs are missing a
qdisc_qstats_backlog_dec when dropping packets to satisfy the
new limit in their change handlers.
One can observe this issue with the following (with tc patched to
support a limit of 0):
export TARGET=fq
tc qdisc del dev lo root
tc qdisc add dev lo root handle 1: tbf rate 8bit burst 100b latency 1ms
tc qdisc replace dev lo handle 3: parent 1:1 $TARGET limit 1000
echo ''; echo 'add child'; tc -s -d qdisc show dev lo
ping -I lo -f -c2 -s32 -W0.001 127.0.0.1 2>&1 >/dev/null
echo ''; echo 'after ping'; tc -s -d qdisc show dev lo
tc qdisc change dev lo handle 3: parent 1:1 $TARGET limit 0
echo ''; echo 'after limit drop'; tc -s -d qdisc show dev lo
tc qdisc replace dev lo handle 2: parent 1:1 sfq
echo ''; echo 'post graft'; tc -s -d qdisc show dev lo
The second to last show command shows 0 packets but a positive
number (74) of backlog bytes. The problem becomes clearer in the
last show command, where qdisc_purge_queue triggers
qdisc_tree_reduce_backlog with the positive backlog and causes an
underflow in the tbf parent's backlog (4096 Mb instead of 0).
To fix this issue, the codepath for all clients of qdisc_dequeue_internal
has been simplified: codel, pie, hhf, fq, fq_pie, and fq_codel.
qdisc_dequeue_internal handles the backlog adjustments for all cases that
do not directly use the dequeue handler.
The old fq_codel_change limit adjustment loop accumulated the arguments to
the subsequent qdisc_tree_reduce_backlog call through the cstats field.
However, this is confusing and error prone as fq_codel_dequeue could also
potentially mutate this field (which qdisc_dequeue_internal calls in the
non gso_skb case), so we have unified the code here with other qdiscs. |
