| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drbd: reject data replies with an out-of-range payload size
recv_dless_read() receives a P_DATA_REPLY from a peer into the bio of an
outstanding read request. The peer-supplied payload length reaches it as
the signed int data_size, and two peer-controlled inputs can make it
negative. With a negotiated data-integrity-alg the digest length is
subtracted first, so a reply whose payload is smaller than the digest
underflows data_size. With no integrity algorithm (the default) data_size
is assigned from the unsigned h95/h100 wire length and drbdd() never
bounds it for a payload-carrying command, so a length above INT_MAX casts
it negative; this path needs no non-default feature. The bio receive loop
then computes expect = min_t(int, data_size, bv_len), which is negative,
and drbd_recv_all_warn(mapped, expect) receives with a size_t of SIZE_MAX
into the first mapped page.
The sibling receive path read_in_block() is not affected: it uses an
unsigned size and rejects it against DRBD_MAX_BIO_SIZE before receiving.
Reject a data reply whose size is negative after the optional digest
subtraction, covering both triggers.
Impact: a malicious or man-in-the-middle DRBD peer copies attacker-chosen
bytes past a bio page in the receiver, corrupting kernel memory. A node
that reads from its peer (a diskless node, or read-balancing to the peer)
is exposed in the default configuration; data-integrity-alg is not
required. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: nfcmrvl: validate helper command length before pull
The firmware download receive path removes the NCI data header and
reads the helper command before validating the remaining packet length.
A short frame can therefore reach the data access before the malformed
packet is rejected.
Validate the complete helper command length before stripping the NCI
data header. |
| In the Linux kernel, the following vulnerability has been resolved:
net: xps: reject an out of range traffic class
Only the entries below dev->num_tc are valid in dev->tc_to_txq[], and
dev->prio_tc_map[] may only name classes below it. netdev_set_num_tc()
lowers dev->num_tc without touching either array.
netdev_txq_to_tc() walks all TC_MAX_QUEUE slots and
netdev_get_prio_tc_map() returns the entry as it stands, so a leftover
entry is handed out as a traffic class >= dev->num_tc. Taking that
class from netdev_txq_to_tc(), __netif_set_xps_queue() rejects only a
negative one and indexes an XPS map sized for dev->num_tc classes:
tci = j * num_tc + tc;
RCU_INIT_POINTER(new_dev_maps->attr_map[tci], map);
attr_map[] holds nr_ids * num_tc entries and j runs over the ids named
in the mask, so a class that is not below num_tc pushes tci past the end
of the map for the last ids and the store overruns it.
Any caller that lowers num_tc leaves such entries behind, and
mqprio_destroy() tears down with netdev_set_num_tc(dev, 0) rather than
netdev_reset_tc(). After mqprio with 8 classes then 1, tc_to_txq[1..7]
still describe txq 1..7. The splat is from an XPS write to txq 2 on a
veth with 8 rx queues: attr_map[] has 8 * 1 entries, tci = j + 2, and
j == 6 stores one past the end of the 88-byte map:
BUG: KASAN: slab-out-of-bounds in __netif_set_xps_queue (net/core/dev.c:2954)
Write of size 8 at addr ffff88813016bc58 by task xps_oob/634
__netif_set_xps_queue (net/core/dev.c:2954)
xps_rxqs_store (net/core/net-sysfs.c:1880)
netdev_queue_attr_store (net/core/net-sysfs.c:1390)
Allocated by task 634:
__kmalloc_noprof (mm/slub.c:5439)
__netif_set_xps_queue (net/core/dev.c:2937)
The buggy address is located 0 bytes to the right of
allocated 88-byte region [ffff88813016bc00, ffff88813016bc58)
Reject a class the map has no room for. |
| Out-of-bounds read in DNS Server allows an authorized attacker to disclose information over a network. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/client: Fix error code in smb2_aead_req_alloc()
The "*num_sgs" variable is a u32 so "ERR_PTR(*num_sgs)" doesn't work.
We would have to do something similar to the previous line where it's
cast to int and then long. However, it's simpler to store the return in
an int ret variable.
This bug would eventually result in a crash when dereference the invalid
error pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: fix two unsafe bare decodes in decode_lockers()
decode_lockers() in cls_lock_client.c contains two bare decode operations
that allow a malicious or compromised OSD to trigger slab-out-of-bounds
reads:
1. ceph_decode_32(p) at the num_lockers field has no preceding bounds
check. ceph_start_decoding() accepts struct_len=0 as valid -- the
internal ceph_decode_need(p, end, 0, bad) always passes -- so when an
OSD sends struct_len=0, ceph_start_decoding() returns success with
p == end. The immediately following bare ceph_decode_32(p) then reads
4 bytes past the validated buffer boundary. The garbage value is
passed directly to kzalloc_objs() as the locker count.
The sibling function decode_watchers() in osd_client.c already uses
ceph_decode_32_safe() after its own ceph_start_decoding() call.
decode_lockers() was the only site using the bare variant.
2. ceph_decode_8(p) after the decode_locker() loop has no preceding
bounds check. If an OSD crafts num_lockers such that the loop
advances p exactly to end, the subsequent bare ceph_decode_8(p) reads
one byte past the validated buffer boundary. The result is passed
directly into *type, which is used as a lock type discriminator by
callers, giving an OSD-controlled one-byte OOB read with direct
influence over the lock type field.
Fix both by replacing bare operations with their safe variants:
ceph_decode_32(p) -> ceph_decode_32_safe(p, end, *num_lockers,
err_inval)
ceph_decode_8(p) -> ceph_decode_8_safe(p, end, *type,
err_free_lockers)
The goto targets differ intentionally:
err_inval: is a new label returning -EINVAL directly. It is used for
the pre-allocation failure path where *lockers is not yet allocated
and must not be passed to ceph_free_lockers().
err_free_lockers: is the existing label. It is used for the
post-allocation failure path where *lockers is allocated and must
be freed.
ret is set to -EINVAL before ceph_decode_8_safe() so that
err_free_lockers returns the correct error code on bounds violation.
Without this, err_free_lockers would return a stale ret value (0 from
the successful decode_locker() loop), silently swallowing the error.
-EINVAL is correct for both failure paths. The data received from the
OSD is structurally malformed. -ENOMEM would misrepresent the failure
class to callers and to stable@ backporters triaging error paths.
Attacker model: a malicious or compromised OSD in a multi-tenant Ceph
deployment can trigger this against any kernel client that issues the
lock.get_info class method (e.g. during RBD exclusive lock acquisition).
[ idryomov: trim changelog, formatting ] |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: st21nfca: validate received frame size
st21nfca_hci_i2c_repack() trims a received frame at its EOF marker
before removing byte stuffing. It then assumes the truncated frame
contains the LLC header and two CRC bytes, and it unconditionally reads
the byte after an escape marker.
A malformed frame can place EOF immediately after the start marker or can
end its data portion with an escape marker. The former leaves too few
bytes for check_crc(), while the latter makes the unstuffing loop read past
the current skb length.
Require the minimum framing bytes both before and after unstuffing. Use
separate input and output cursors while removing byte stuffing, and reject
an escape marker without its encoded byte. This keeps malformed frames
within the received frame boundary before CRC processing. |
| In the Linux kernel, the following vulnerability has been resolved:
net: gue: reject invalid REMCSUM offsets
The REMCSUM option carries an absolute checksum start and checksum field
offset. gue_remcsum() passes them to skb_remcsum_process(), whose
partial path stores offset - start in the u16 skb->csum_offset variable.
If offset is less than start, this underflows.
A forwarded packet can retain CHECKSUM_PARTIAL and reach a NETIF_F_HW_CSUM
driver which trusts the metadata, leading skb_copy_and_csum_dev() to write
two bytes about 64 KiB beyond the destination buffer.
Reject reversed tuples in validate_gue_flags(), after the existing length
validation, so all GUE parsers enforce the ordering in one place. |
| A flaw was found in SmallRye GraphQL. The number scalar coercion for BigInteger does not properly validate the magnitude of float or string inputs. An unauthenticated remote attacker can exploit this by sending a GraphQL query containing a large exponent float literal. This can lead to the allocation of extremely large BigInteger objects, causing CPU exhaustion or an OutOfMemoryError, resulting in a denial of service. |
| A flaw was found in the Qute template engine, which is used by Quarkus to generate dynamic content like HTML pages or emails. The issue exists in the component responsible for looking up data values (ReflectionValueResolver), which fails to properly block access to sensitive Java internal functions when processing certain data types like Enums. An attacker who can provide or influence the template text can exploit this bypass to take control of the server by executing unauthorized commands. |
| A flaw was found in Keycloak Policy Enforcer. This vulnerability allows any authenticated user to bypass all authorization policies, including role, scope, and User-Managed Access (UMA) permission checks. By including the configured access-denied page path within a request URL, either as a path segment or a query parameter, an attacker can gain unauthorized access to protected resources. |
| A flaw was found in Smallrye, where smallrye-fault-tolerance is vulnerable to an out-of-memory (OOM) issue. This vulnerability is externally triggered when calling the metrics URI. Every call creates a new object within meterMap and may lead to a denial of service (DoS) issue. |
| A Regular-Expression Denial of Service (ReDoS) in the Markdown2. extract_metadata() function (lib/markdown2.py) of trentm markdown2 through v2.5.5 allows attackers to cause a Denial of Service (DoS) via a crafted Markdown document. |
| Nodemailer from 3.0.0 before 10.0.10 contains a denial of service vulnerability in MessageParser.parseHeaders that allows users to exhaust CPU through quadratic header unfolding. Attackers can supply large recipient lists or long headers that fold into tens of thousands of continuation lines, blocking the Node.js event loop during DKIM signing. |
| n8n before 2.41.4 and 2.42.x before 2.42.1 contains a signature bypass in the waiting-webhook endpoint, which selects Send-and-Wait validation before normalising an alternate node reference form. Attackers holding an execution's resume token can approve waiting executions meant for others, running downstream actions under the workflow owner's credentials, potentially including command execution. |
| A security vulnerability has been detected in Praat up to 7.0.02. Affected is the function whisper_model_load of the file external/whispercpp/whisper.cpp of the component Model Loader. The manipulation of the argument n_dims leads to out-of-bounds write. The attack can be initiated remotely. The exploit has been disclosed publicly and may be used. The identifier of the patch is a910d21a2705ef4cd16d91f29cdc8da1ab1a7221. To fix this issue, it is recommended to deploy a patch. The project maintainer confirms: "We did a quick fix (suggested fix 1) for Praat version 7.0.03, and scheduled a better fix (suggested fix 2)." |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_ct: bail out on template ct in get eval
I noticed this issue while looking at a historic syzbot report [1].
A rule like the one below is enough to trigger the bug:
table ip t {
chain pre {
type filter hook prerouting priority raw;
ct zone set 1
ct original saddr 1.2.3.4 accept
}
}
The first expression attaches a per-cpu template ct via
nft_ct_set_zone_eval() (nf_ct_tmpl_alloc -> kzalloc, tuple is all
zero, nf_ct_l3num(ct) == 0). The next expression then calls
nft_ct_get_eval() on the same skb, treats the template as a real ct
and hits the 16-byte memcpy path. With dreg at NFT_REG32_15 this
overflows past struct nft_regs on the kernel stack; with smaller
dreg values it silently clobbers adjacent registers.
Reject template ct at the eval entry and in nft_ct_get_fast_eval(),
mirroring the check nft_ct_set_eval() already has. Additionally,
bound the address copy in NFT_CT_SRC / NFT_CT_DST by priv->len
instead of by nf_ct_l3num(ct): nf_ct_get_tuple() zeroes the tuple
before pkt_to_tuple() fills in only the protocol-relevant leading
bytes, so the trailing bytes of tuple->{src,dst}.u3.all are
well-defined zero. priv->len is validated at rule load, so the
copy size is now bounded by the destination register rather than
by an untrusted field on the conntrack.
[1]: https://syzkaller.appspot.com/bug?id=389cf09cb72926114fce90dc85a2c3231dcb647c |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: errata: Mitigate TLBI errata on various Arm CPUs
A number of CPUs developed by Arm suffer from errata whereby a broadcast
TLBI;DSB sequence may complete before the global observation of writes
which are translated by an affected TLB entry.
These errata ONLY affect the completion of memory accesses which have
been translated by an invalidated TLB entry, and these errata DO NOT
affect the actual invalidation of TLB entries. TLB entries are removed
correctly.
This issue has been assigned CVE ID CVE-2025-10263.
To mitigate this issue, Arm recommends that software follows any
affected TLBI;DSB sequence with an additional TLBI;DSB, which will
ensure that all memory write effects affected by the first TLBI have
been globally observed. The additional TLBI can use any operation that
is broadcast to affected CPUs, and the additional DSB can use any option
that is sufficient to complete the additional TLBI.
The ARM64_WORKAROUND_REPEAT_TLBI workaround is sufficient to mitigate
the issue. Enable this workaround for affected CPUs, and update the
silicon errata documentation accordingly.
Note that due to the manner in which Arm develops IP and tracks errata,
some CPUs share a common erratum number. |
| Godot Engine through 4.7.2 has a heap out-of-bounds write in the binary resource loader (core/io/resource_format_binary.cpp, ResourceLoaderBinary::get_unicode_string). A string length is read from the resource file into a signed 32-bit integer and compared against the destination buffer size with a signed comparison, which conditionally resizes the buffer. A negative length value skips the resize; the same value is then passed to the copy routine as an unsigned byte count, where it sign-extends to a huge value, copying file-controlled data far past the undersized heap allocation. The defect is reached when the product or an exported game loads a crafted binary resource file (.res). NOTE: the Supplier's position is that the research has identified "no security issues" because the required attacker access is outside of the current Godot Engine threat model. |
| libsmb2 through 6.2 contains an integer underflow vulnerability in decode_acl that allows malicious SMB servers to trigger heap out-of-bounds reads via crafted security descriptors. Attackers controlling a server or intercepting unsigned sessions can send an AclSize below 8 in a QUERY_INFO reply, bypassing ACE bounds checks and crashing the client. |
