| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: pci-epf-vntb: Remove duplicate resource teardown
epf_ntb_epc_destroy() duplicates the teardown that the caller is
supposed to perform later. This leads to an oops when .allow_link fails
or when .drop_link is performed. The following is an example oops of the
former case:
Unable to handle kernel paging request at virtual address dead000000000108
[...]
[dead000000000108] address between user and kernel address ranges
Internal error: Oops: 0000000096000044 [#1] SMP
[...]
Call trace:
pci_epc_remove_epf+0x78/0xe0 (P)
pci_primary_epc_epf_link+0x88/0xa8
configfs_symlink+0x1f4/0x5a0
vfs_symlink+0x134/0x1d8
do_symlinkat+0x88/0x138
__arm64_sys_symlinkat+0x74/0xe0
[...]
Remove the helper, and drop pci_epc_put(). EPC device refcounting is
tied to the configfs EPC group lifetime, and pci_epc_put() in the
.drop_link path is sufficient. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Drop WARN on large size for KVM_MEMORY_ENCRYPT_REG_REGION
Drop the WARN in sev_pin_memory() on npages overflowing an int, as the
WARN is comically trivially to trigger from userspace, e.g. by doing:
struct kvm_enc_region range = {
.addr = 0,
.size = -1ul,
};
__vm_ioctl(vm, KVM_MEMORY_ENCRYPT_REG_REGION, &range);
Note, the checks in sev_mem_enc_register_region() that presumably exist to
verify the incoming address+size are completely worthless, as both "addr"
and "size" are u64s and SEV is 64-bit only, i.e. they _can't_ be greater
than ULONG_MAX. That wart will be cleaned up in the near future.
if (range->addr > ULONG_MAX || range->size > ULONG_MAX)
return -EINVAL;
Opportunistically add a comment to explain why the code calculates the
number of pages the "hard" way, e.g. instead of just shifting @ulen. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: qcom: q6apm: move component registration to unmanaged version
q6apm component registers dais dynamically from ASoC toplology, which
are allocated using device managed version apis. Allocating both
component and dynamic dais using managed version could lead to incorrect
free ordering, dai will be freed while component still holding references
to it.
Fix this issue by moving component to unmanged version so
that the dai pointers are only freeded after the component is removed.
==================================================================
BUG: KASAN: slab-use-after-free in snd_soc_del_component_unlocked+0x3d4/0x400 [snd_soc_core]
Read of size 8 at addr ffff00084493a6e8 by task kworker/u48:0/3426
Tainted: [W]=WARN
Hardware name: LENOVO 21N2ZC5PUS/21N2ZC5PUS, BIOS N42ET57W (1.31 ) 08/08/2024
Workqueue: pdr_notifier_wq pdr_notifier_work [pdr_interface]
Call trace:
show_stack+0x28/0x7c (C)
dump_stack_lvl+0x60/0x80
print_report+0x160/0x4b4
kasan_report+0xac/0xfc
__asan_report_load8_noabort+0x20/0x34
snd_soc_del_component_unlocked+0x3d4/0x400 [snd_soc_core]
snd_soc_unregister_component_by_driver+0x50/0x88 [snd_soc_core]
devm_component_release+0x30/0x5c [snd_soc_core]
devres_release_all+0x13c/0x210
device_unbind_cleanup+0x20/0x190
device_release_driver_internal+0x350/0x468
device_release_driver+0x18/0x30
bus_remove_device+0x1a0/0x35c
device_del+0x314/0x7f0
device_unregister+0x20/0xbc
apr_remove_device+0x5c/0x7c [apr]
device_for_each_child+0xd8/0x160
apr_pd_status+0x7c/0xa8 [apr]
pdr_notifier_work+0x114/0x240 [pdr_interface]
process_one_work+0x500/0xb70
worker_thread+0x630/0xfb0
kthread+0x370/0x6c0
ret_from_fork+0x10/0x20
Allocated by task 77:
kasan_save_stack+0x40/0x68
kasan_save_track+0x20/0x40
kasan_save_alloc_info+0x44/0x58
__kasan_kmalloc+0xbc/0xdc
__kmalloc_node_track_caller_noprof+0x1f4/0x620
devm_kmalloc+0x7c/0x1c8
snd_soc_register_dai+0x50/0x4f0 [snd_soc_core]
soc_tplg_pcm_elems_load+0x55c/0x1eb8 [snd_soc_core]
snd_soc_tplg_component_load+0x4f8/0xb60 [snd_soc_core]
audioreach_tplg_init+0x124/0x1fc [snd_q6apm]
q6apm_audio_probe+0x10/0x1c [snd_q6apm]
snd_soc_component_probe+0x5c/0x118 [snd_soc_core]
soc_probe_component+0x44c/0xaf0 [snd_soc_core]
snd_soc_bind_card+0xad0/0x2370 [snd_soc_core]
snd_soc_register_card+0x3b0/0x4c0 [snd_soc_core]
devm_snd_soc_register_card+0x50/0xc8 [snd_soc_core]
x1e80100_platform_probe+0x208/0x368 [snd_soc_x1e80100]
platform_probe+0xc0/0x188
really_probe+0x188/0x804
__driver_probe_device+0x158/0x358
driver_probe_device+0x60/0x190
__device_attach_driver+0x16c/0x2a8
bus_for_each_drv+0x100/0x194
__device_attach+0x174/0x380
device_initial_probe+0x14/0x20
bus_probe_device+0x124/0x154
deferred_probe_work_func+0x140/0x220
process_one_work+0x500/0xb70
worker_thread+0x630/0xfb0
kthread+0x370/0x6c0
ret_from_fork+0x10/0x20
Freed by task 3426:
kasan_save_stack+0x40/0x68
kasan_save_track+0x20/0x40
__kasan_save_free_info+0x4c/0x80
__kasan_slab_free+0x78/0xa0
kfree+0x100/0x4a4
devres_release_all+0x144/0x210
device_unbind_cleanup+0x20/0x190
device_release_driver_internal+0x350/0x468
device_release_driver+0x18/0x30
bus_remove_device+0x1a0/0x35c
device_del+0x314/0x7f0
device_unregister+0x20/0xbc
apr_remove_device+0x5c/0x7c [apr]
device_for_each_child+0xd8/0x160
apr_pd_status+0x7c/0xa8 [apr]
pdr_notifier_work+0x114/0x240 [pdr_interface]
process_one_work+0x500/0xb70
worker_thread+0x630/0xfb0
kthread+0x370/0x6c0
ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
media: vidtv: fix nfeeds state corruption on start_streaming failure
syzbot reported a memory leak in vidtv_psi_service_desc_init [1].
When vidtv_start_streaming() fails inside vidtv_start_feed(), the
nfeeds counter is left incremented even though no feed was actually
started. This corrupts the driver state: subsequent start_feed calls
see nfeeds > 1 and skip starting the mux, while stop_feed calls
eventually try to stop a non-existent stream.
This state corruption can also lead to memory leaks, since the mux
and channel resources may be partially allocated during a failed
start_streaming but never cleaned up, as the stop path finds
dvb->streaming == false and returns early.
Fix by decrementing nfeeds back when start_streaming fails, keeping
the counter in sync with the actual number of active feeds.
[1]
BUG: memory leak
unreferenced object 0xffff888145b50820 (size 32):
comm "syz.0.17", pid 6068, jiffies 4294944486
backtrace (crc 90a0c7d4):
vidtv_psi_service_desc_init+0x74/0x1b0 drivers/media/test-drivers/vidtv/vidtv_psi.c:288
vidtv_channel_s302m_init+0xb1/0x2a0 drivers/media/test-drivers/vidtv/vidtv_channel.c:83
vidtv_channels_init+0x1b/0x40 drivers/media/test-drivers/vidtv/vidtv_channel.c:524
vidtv_mux_init+0x516/0xbe0 drivers/media/test-drivers/vidtv/vidtv_mux.c:518
vidtv_start_streaming drivers/media/test-drivers/vidtv/vidtv_bridge.c:194 [inline]
vidtv_start_feed+0x33e/0x4d0 drivers/media/test-drivers/vidtv/vidtv_bridge.c:239 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: 6fire: fix use-after-free on disconnect
In usb6fire_chip_abort(), the chip struct is allocated as the card's
private data (via snd_card_new with sizeof(struct sfire_chip)). When
snd_card_free_when_closed() is called and no file handles are open, the
card and embedded chip are freed synchronously. The subsequent
chip->card = NULL write then hits freed slab memory.
Call trace:
usb6fire_chip_abort sound/usb/6fire/chip.c:59 [inline]
usb6fire_chip_disconnect+0x348/0x358 sound/usb/6fire/chip.c:182
usb_unbind_interface+0x1a8/0x88c drivers/usb/core/driver.c:458
...
hub_event+0x1a04/0x4518 drivers/usb/core/hub.c:5953
Fix by moving the card lifecycle out of usb6fire_chip_abort() and into
usb6fire_chip_disconnect(). The card pointer is saved in a local
before any teardown, snd_card_disconnect() is called first to prevent
new opens, URBs are aborted while chip is still valid, and
snd_card_free_when_closed() is called last so chip is never accessed
after the card may be freed. |
| In the Linux kernel, the following vulnerability has been resolved:
media: as102: fix to not free memory after the device is registered in as102_usb_probe()
In as102_usb driver, the following race condition occurs:
```
CPU0 CPU1
as102_usb_probe()
kzalloc(); // alloc as102_dev_t
....
usb_register_dev();
fd = sys_open("/path/to/dev"); // open as102 fd
....
usb_deregister_dev();
....
kfree(); // free as102_dev_t
....
sys_close(fd);
as102_release() // UAF!!
as102_usb_release()
kfree(); // DFB!!
```
When a USB character device registered with usb_register_dev() is later
unregistered (via usb_deregister_dev() or disconnect), the device node is
removed so new open() calls fail. However, file descriptors that are
already open do not go away immediately: they remain valid until the last
reference is dropped and the driver's .release() is invoked.
In as102, as102_usb_probe() calls usb_register_dev() and then, on an
error path, does usb_deregister_dev() and frees as102_dev_t right away.
If userspace raced a successful open() before the deregistration, that
open FD will later hit as102_release() --> as102_usb_release() and access
or free as102_dev_t again, occur a race to use-after-free and
double-free vuln.
The fix is to never kfree(as102_dev_t) directly once usb_register_dev()
has succeeded. After deregistration, defer freeing memory to .release().
In other words, let release() perform the last kfree when the final open
FD is closed. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix NULL i_assoc_inode dereference in nilfs_mdt_save_to_shadow_map
The DAT inode's btree node cache (i_assoc_inode) is initialized lazily
during btree operations. However, nilfs_mdt_save_to_shadow_map()
assumes i_assoc_inode is already initialized when copying dirty pages
to the shadow map during GC.
If NILFS_IOCTL_CLEAN_SEGMENTS is called immediately after mount before
any btree operation has occurred on the DAT inode, i_assoc_inode is
NULL leading to a general protection fault.
Fix this by calling nilfs_attach_btree_node_cache() on the DAT inode
in nilfs_dat_read() at mount time, ensuring i_assoc_inode is always
initialized before any GC operation can use it. |
| In the Linux kernel, the following vulnerability has been resolved:
media: hackrf: fix to not free memory after the device is registered in hackrf_probe()
In hackrf driver, the following race condition occurs:
```
CPU0 CPU1
hackrf_probe()
kzalloc(); // alloc hackrf_dev
....
v4l2_device_register();
....
fd = sys_open("/path/to/dev"); // open hackrf fd
....
v4l2_device_unregister();
....
kfree(); // free hackrf_dev
....
sys_ioctl(fd, ...);
v4l2_ioctl();
video_is_registered() // UAF!!
....
sys_close(fd);
v4l2_release() // UAF!!
hackrf_video_release()
kfree(); // DFB!!
```
When a V4L2 or video device is unregistered, the device node is removed so
new open() calls are blocked.
However, file descriptors that are already open-and any in-flight I/O-do
not terminate immediately; they remain valid until the last reference is
dropped and the driver's release() is invoked.
Therefore, freeing device memory on the error path after hackrf_probe()
has registered dev it will lead to a race to use-after-free vuln, since
those already-open handles haven't been released yet.
And since release() free memory too, race to use-after-free and
double-free vuln occur.
To prevent this, if device is registered from probe(), it should be
modified to free memory only through release() rather than calling
kfree() directly. |
| In the Linux kernel, the following vulnerability has been resolved:
driver core: platform: use generic driver_override infrastructure
When a driver is probed through __driver_attach(), the bus' match()
callback is called without the device lock held, thus accessing the
driver_override field without a lock, which can cause a UAF.
Fix this by using the driver-core driver_override infrastructure taking
care of proper locking internally.
Note that calling match() from __driver_attach() without the device lock
held is intentional. [1] |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: do not expire session on binding failure
When a multichannel session binding request fails (e.g. wrong password),
the error path unconditionally sets sess->state = SMB2_SESSION_EXPIRED.
However, during binding, sess points to the target session looked up via
ksmbd_session_lookup_slowpath() -- which belongs to another connection's
user. This allows a remote attacker to invalidate any active session by
simply sending a binding request with a wrong password (DoS).
Fix this by skipping session expiration when the failed request was
a binding attempt, since the session does not belong to the current
connection. The reference taken by ksmbd_session_lookup_slowpath() is
still correctly released via ksmbd_user_session_put(). |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: unset conn->binding on failed binding request
When a multichannel SMB2_SESSION_SETUP request with
SMB2_SESSION_REQ_FLAG_BINDING fails ksmbd sets conn->binding = true
but never clears it on the error path. This leaves the connection in
a binding state where all subsequent ksmbd_session_lookup_all() calls
fall back to the global sessions table. This fix it by clearing
conn->binding = false in the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/imagination: Synchronize interrupts before suspending the GPU
The runtime PM suspend callback doesn't know whether the IRQ handler is
in progress on a different CPU core and doesn't wait for it to finish.
Depending on timing, the IRQ handler could be running while the GPU is
suspended, leading to kernel crashes when trying to access GPU
registers. See example signature below.
In a power off sequence initiated by the runtime PM suspend callback,
wait for any IRQ handlers in progress on other CPU cores to finish, by
calling synchronize_irq().
At the same time, remove the runtime PM resume/put calls in the threaded
IRQ handler. On top of not being the right approach to begin with, and
being at the wrong place as they should have wrapped all GPU register
accesses, the driver would hit a deadlock between synchronize_irq()
being called from a runtime PM suspend callback, holding the device
power lock, and the resume callback requiring the same.
Example crash signature on a TI AM68 SK platform:
[ 337.241218] SError Interrupt on CPU0, code 0x00000000bf000000 -- SError
[ 337.241239] CPU: 0 UID: 0 PID: 112 Comm: irq/234-gpu Tainted: G M 6.17.7-B2C-00005-g9c7bbe4ea16c #2 PREEMPT
[ 337.241246] Tainted: [M]=MACHINE_CHECK
[ 337.241249] Hardware name: Texas Instruments AM68 SK (DT)
[ 337.241252] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 337.241256] pc : pvr_riscv_irq_pending+0xc/0x24
[ 337.241277] lr : pvr_device_irq_thread_handler+0x64/0x310
[ 337.241282] sp : ffff800085b0bd30
[ 337.241284] x29: ffff800085b0bd50 x28: ffff0008070d9eab x27: ffff800083a5ce10
[ 337.241291] x26: ffff000806e48f80 x25: ffff0008070d9eac x24: 0000000000000000
[ 337.241296] x23: ffff0008068e9bf0 x22: ffff0008068e9bd0 x21: ffff800085b0bd30
[ 337.241301] x20: ffff0008070d9e00 x19: ffff0008068e9000 x18: 0000000000000001
[ 337.241305] x17: 637365645f656c70 x16: 0000000000000000 x15: ffff000b7df9ff40
[ 337.241310] x14: 0000a585fe3c0d0e x13: 000000999704f060 x12: 000000000002771a
[ 337.241314] x11: 00000000000000c0 x10: 0000000000000af0 x9 : ffff800085b0bd00
[ 337.241318] x8 : ffff0008071175d0 x7 : 000000000000b955 x6 : 0000000000000003
[ 337.241323] x5 : 0000000000000000 x4 : 0000000000000002 x3 : 0000000000000000
[ 337.241327] x2 : ffff800080e39d20 x1 : ffff800080e3fc48 x0 : 0000000000000000
[ 337.241333] Kernel panic - not syncing: Asynchronous SError Interrupt
[ 337.241337] CPU: 0 UID: 0 PID: 112 Comm: irq/234-gpu Tainted: G M 6.17.7-B2C-00005-g9c7bbe4ea16c #2 PREEMPT
[ 337.241342] Tainted: [M]=MACHINE_CHECK
[ 337.241343] Hardware name: Texas Instruments AM68 SK (DT)
[ 337.241345] Call trace:
[ 337.241348] show_stack+0x18/0x24 (C)
[ 337.241357] dump_stack_lvl+0x60/0x80
[ 337.241364] dump_stack+0x18/0x24
[ 337.241368] vpanic+0x124/0x2ec
[ 337.241373] abort+0x0/0x4
[ 337.241377] add_taint+0x0/0xbc
[ 337.241384] arm64_serror_panic+0x70/0x80
[ 337.241389] do_serror+0x3c/0x74
[ 337.241392] el1h_64_error_handler+0x30/0x48
[ 337.241400] el1h_64_error+0x6c/0x70
[ 337.241404] pvr_riscv_irq_pending+0xc/0x24 (P)
[ 337.241410] irq_thread_fn+0x2c/0xb0
[ 337.241416] irq_thread+0x170/0x334
[ 337.241421] kthread+0x12c/0x210
[ 337.241428] ret_from_fork+0x10/0x20
[ 337.241434] SMP: stopping secondary CPUs
[ 337.241451] Kernel Offset: disabled
[ 337.241453] CPU features: 0x040000,02002800,20002001,0400421b
[ 337.241456] Memory Limit: none
[ 337.457921] ---[ end Kernel panic - not syncing: Asynchronous SError Interrupt ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Limit BO list entry count to prevent resource exhaustion
Userspace can pass an arbitrary number of BO list entries via the
bo_number field. Although the previous multiplication overflow check
prevents out-of-bounds allocation, a large number of entries could still
cause excessive memory allocation (up to potentially gigabytes) and
unnecessarily long list processing times.
Introduce a hard limit of 128k entries per BO list, which is more than
sufficient for any realistic use case (e.g., a single list containing all
buffers in a large scene). This prevents memory exhaustion attacks and
ensures predictable performance.
Return -EINVAL if the requested entry count exceeds the limit
(cherry picked from commit 688b87d39e0aa8135105b40dc167d74b5ada5332) |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: fix deadlock when reading partition table
When one process(such as udev) opens ublk block device (e.g., to read
the partition table via bdev_open()), a deadlock[1] can occur:
1. bdev_open() grabs disk->open_mutex
2. The process issues read I/O to ublk backend to read partition table
3. In __ublk_complete_rq(), blk_update_request() or blk_mq_end_request()
runs bio->bi_end_io() callbacks
4. If this triggers fput() on file descriptor of ublk block device, the
work may be deferred to current task's task work (see fput() implementation)
5. This eventually calls blkdev_release() from the same context
6. blkdev_release() tries to grab disk->open_mutex again
7. Deadlock: same task waiting for a mutex it already holds
The fix is to run blk_update_request() and blk_mq_end_request() with bottom
halves disabled. This forces blkdev_release() to run in kernel work-queue
context instead of current task work context, and allows ublk server to make
forward progress, and avoids the deadlock.
[axboe: rewrite comment in ublk] |
| In the Linux kernel, the following vulnerability has been resolved:
can: gs_usb: gs_usb_xmit_callback(): fix handling of failed transmitted URBs
The driver lacks the cleanup of failed transfers of URBs. This reduces the
number of available URBs per error by 1. This leads to reduced performance
and ultimately to a complete stop of the transmission.
If the sending of a bulk URB fails do proper cleanup:
- increase netdev stats
- mark the echo_sbk as free
- free the driver's context and do accounting
- wake the send queue |
| In the Linux kernel, the following vulnerability has been resolved:
sched/deadline: Stop dl_server before CPU goes offline
IBM CI tool reported kernel warning[1] when running a CPU removal
operation through drmgr[2]. i.e "drmgr -c cpu -r -q 1"
WARNING: CPU: 0 PID: 0 at kernel/sched/cpudeadline.c:219 cpudl_set+0x58/0x170
NIP [c0000000002b6ed8] cpudl_set+0x58/0x170
LR [c0000000002b7cb8] dl_server_timer+0x168/0x2a0
Call Trace:
[c000000002c2f8c0] init_stack+0x78c0/0x8000 (unreliable)
[c0000000002b7cb8] dl_server_timer+0x168/0x2a0
[c00000000034df84] __hrtimer_run_queues+0x1a4/0x390
[c00000000034f624] hrtimer_interrupt+0x124/0x300
[c00000000002a230] timer_interrupt+0x140/0x320
Git bisects to: commit 4ae8d9aa9f9d ("sched/deadline: Fix dl_server getting stuck")
This happens since:
- dl_server hrtimer gets enqueued close to cpu offline, when
kthread_park enqueues a fair task.
- CPU goes offline and drmgr removes it from cpu_present_mask.
- hrtimer fires and warning is hit.
Fix it by stopping the dl_server before CPU is marked dead.
[1]: https://lore.kernel.org/all/8218e149-7718-4432-9312-f97297c352b9@linux.ibm.com/
[2]: https://github.com/ibm-power-utilities/powerpc-utils/tree/next/src/drmgr
[sshegde: wrote the changelog and tested it] |
| In the Linux kernel, the following vulnerability has been resolved:
spi: cadence-quadspi: Implement refcount to handle unbind during busy
driver support indirect read and indirect write operation with
assumption no force device removal(unbind) operation. However
force device removal(removal) is still available to root superuser.
Unbinding driver during operation causes kernel crash. This changes
ensure driver able to handle such operation for indirect read and
indirect write by implementing refcount to track attached devices
to the controller and gracefully wait and until attached devices
remove operation completed before proceed with removal operation. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: compress: fix UAF of f2fs_inode_info in f2fs_free_dic
The decompress_io_ctx may be released asynchronously after
I/O completion. If this file is deleted immediately after read,
and the kworker of processing post_read_wq has not been executed yet
due to high workloads, It is possible that the inode(f2fs_inode_info)
is evicted and freed before it is used f2fs_free_dic.
The UAF case as below:
Thread A Thread B
- f2fs_decompress_end_io
- f2fs_put_dic
- queue_work
add free_dic work to post_read_wq
- do_unlink
- iput
- evict
- call_rcu
This file is deleted after read.
Thread C kworker to process post_read_wq
- rcu_do_batch
- f2fs_free_inode
- kmem_cache_free
inode is freed by rcu
- process_scheduled_works
- f2fs_late_free_dic
- f2fs_free_dic
- f2fs_release_decomp_mem
read (dic->inode)->i_compress_algorithm
This patch store compress_algorithm and sbi in dic to avoid inode UAF.
In addition, the previous solution is deprecated in [1] may cause system hang.
[1] https://lore.kernel.org/all/c36ab955-c8db-4a8b-a9d0-f07b5f426c3f@kernel.org |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to trigger foreground gc during f2fs_map_blocks() in lfs mode
w/ "mode=lfs" mount option, generic/299 will cause system panic as below:
------------[ cut here ]------------
kernel BUG at fs/f2fs/segment.c:2835!
Call Trace:
<TASK>
f2fs_allocate_data_block+0x6f4/0xc50
f2fs_map_blocks+0x970/0x1550
f2fs_iomap_begin+0xb2/0x1e0
iomap_iter+0x1d6/0x430
__iomap_dio_rw+0x208/0x9a0
f2fs_file_write_iter+0x6b3/0xfa0
aio_write+0x15d/0x2e0
io_submit_one+0x55e/0xab0
__x64_sys_io_submit+0xa5/0x230
do_syscall_64+0x84/0x2f0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0010:new_curseg+0x70f/0x720
The root cause of we run out-of-space is: in f2fs_map_blocks(), f2fs may
trigger foreground gc only if it allocates any physical block, it will be
a little bit later when there is multiple threads writing data w/
aio/dio/bufio method in parallel, since we always use OPU in lfs mode, so
f2fs_map_blocks() does block allocations aggressively.
In order to fix this issue, let's give a chance to trigger foreground
gc in prior to block allocation in f2fs_map_blocks(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: clean up FDB, MDB, VLAN entries on unbind
As explained in many places such as commit b117e1e8a86d ("net: dsa:
delete dsa_legacy_fdb_add and dsa_legacy_fdb_del"), DSA is written given
the assumption that higher layers have balanced additions/deletions.
As such, it only makes sense to be extremely vocal when those
assumptions are violated and the driver unbinds with entries still
present.
But Ido Schimmel points out a very simple situation where that is wrong:
https://lore.kernel.org/netdev/ZDazSM5UsPPjQuKr@shredder/
(also briefly discussed by me in the aforementioned commit).
Basically, while the bridge bypass operations are not something that DSA
explicitly documents, and for the majority of DSA drivers this API
simply causes them to go to promiscuous mode, that isn't the case for
all drivers. Some have the necessary requirements for bridge bypass
operations to do something useful - see dsa_switch_supports_uc_filtering().
Although in tools/testing/selftests/net/forwarding/local_termination.sh,
we made an effort to popularize better mechanisms to manage address
filters on DSA interfaces from user space - namely macvlan for unicast,
and setsockopt(IP_ADD_MEMBERSHIP) - through mtools - for multicast, the
fact is that 'bridge fdb add ... self static local' also exists as
kernel UAPI, and might be useful to someone, even if only for a quick
hack.
It seems counter-productive to block that path by implementing shim
.ndo_fdb_add and .ndo_fdb_del operations which just return -EOPNOTSUPP
in order to prevent the ndo_dflt_fdb_add() and ndo_dflt_fdb_del() from
running, although we could do that.
Accepting that cleanup is necessary seems to be the only option.
Especially since we appear to be coming back at this from a different
angle as well. Russell King is noticing that the WARN_ON() triggers even
for VLANs:
https://lore.kernel.org/netdev/Z_li8Bj8bD4-BYKQ@shell.armlinux.org.uk/
What happens in the bug report above is that dsa_port_do_vlan_del() fails,
then the VLAN entry lingers on, and then we warn on unbind and leak it.
This is not a straight revert of the blamed commit, but we now add an
informational print to the kernel log (to still have a way to see
that bugs exist), and some extra comments gathered from past years'
experience, to justify the logic. |
