| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: xps: reject an out of range traffic class
Only the entries below dev->num_tc are valid in dev->tc_to_txq[], and
dev->prio_tc_map[] may only name classes below it. netdev_set_num_tc()
lowers dev->num_tc without touching either array.
netdev_txq_to_tc() walks all TC_MAX_QUEUE slots and
netdev_get_prio_tc_map() returns the entry as it stands, so a leftover
entry is handed out as a traffic class >= dev->num_tc. Taking that
class from netdev_txq_to_tc(), __netif_set_xps_queue() rejects only a
negative one and indexes an XPS map sized for dev->num_tc classes:
tci = j * num_tc + tc;
RCU_INIT_POINTER(new_dev_maps->attr_map[tci], map);
attr_map[] holds nr_ids * num_tc entries and j runs over the ids named
in the mask, so a class that is not below num_tc pushes tci past the end
of the map for the last ids and the store overruns it.
Any caller that lowers num_tc leaves such entries behind, and
mqprio_destroy() tears down with netdev_set_num_tc(dev, 0) rather than
netdev_reset_tc(). After mqprio with 8 classes then 1, tc_to_txq[1..7]
still describe txq 1..7. The splat is from an XPS write to txq 2 on a
veth with 8 rx queues: attr_map[] has 8 * 1 entries, tci = j + 2, and
j == 6 stores one past the end of the 88-byte map:
BUG: KASAN: slab-out-of-bounds in __netif_set_xps_queue (net/core/dev.c:2954)
Write of size 8 at addr ffff88813016bc58 by task xps_oob/634
__netif_set_xps_queue (net/core/dev.c:2954)
xps_rxqs_store (net/core/net-sysfs.c:1880)
netdev_queue_attr_store (net/core/net-sysfs.c:1390)
Allocated by task 634:
__kmalloc_noprof (mm/slub.c:5439)
__netif_set_xps_queue (net/core/dev.c:2937)
The buggy address is located 0 bytes to the right of
allocated 88-byte region [ffff88813016bc00, ffff88813016bc58)
Reject a class the map has no room for. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: use one headroom snapshot for neighbour replies
vxlan_na_create() samples LL_RESERVED_SPACE() to size the reply skb and then
samples it again to reserve headroom. A concurrent vxlan_changelink() can
update needed_headroom between the two reads, creating a TOCTOU race. The
second value can exceed the allocation and make the Ethernet header write out
of bounds.
The race is reproducible on the unpatched kernel. It occurred when
vxlan_na_create() generated a neighbour reply while vxlan_changelink() changed
the link headroom. KASAN caught a four-byte write two bytes beyond a 704-byte
skbuff_small_head allocation.
Snapshot the headroom once and use that value for both allocation and
reservation. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: fix slab-out-of-bounds reads when logging service names
nfc_llcp_wks_sap() and nfc_llcp_build_sdreq_tlv() pass non-null-
terminated strings to pr_debug() using the %s format specifier.
The buffers are allocated via kmemdup() or come from netlink
attributes and are not guaranteed to be null-terminated, causing
__dynamic_pr_debug() to read beyond the allocated region:
KASAN: slab-out-of-bounds Read in __dynamic_pr_debug
Fix both call sites by using %.*s with the explicit length to limit
the output to the actual length of the string. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: fix WKS SAP hijacking via prefix match in nfc_llcp_wks_sap()
nfc_llcp_wks_sap() compares only service_name_len bytes, so a short
service_name like "u" matches longer WKS strings like "urn:nfc:sn:snep".
Fix by requiring exact length match before strncmp(). |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: fix sdreq TLV list leak on parse/alloc/send failure
nfc_genl_llc_sdreq() builds a list of TLV nodes while walking nested
netlink attrs, but 3 error paths (nested-attr parse failure, TLV alloc
ENOMEM, nfc_llcp_send_snl_sdreq() failure) all skip freeing what was
already queued.
Route them through a new free_list label, mirroring the SDRES path in
the same file which already does this. Harmless on the success path
too -- send_snl_sdreq() drains the list as it moves nodes, so it's
already empty by the time free_list runs. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: Fix list corruption / refcount desync in nfc_llcp_recv_dm()
nfc_llcp_recv_dm() handles DM(NOBOUND)/DM(REJ) for a socket that is still
linked on local->connecting_sockets: it looks the socket up with
nfc_llcp_connecting_sock_get(), sets sk->sk_state = LLCP_CLOSED and
returns, without taking the socket lock and without unlinking the socket
from the connecting_sockets list.
llcp_sock_release() selects the list to unlink from by sk_state: a socket
in LLCP_CONNECTING is unlinked from connecting_sockets, otherwise from the
sockets list. Because recv_dm left the socket physically on
connecting_sockets but in the LLCP_CLOSED state, release() takes the else
branch and calls nfc_llcp_sock_unlink(&local->sockets, sk). That runs
sk_del_node_init() while holding sockets.lock, i.e. it removes the socket
from the connecting_sockets hlist under the wrong lock. A concurrent
connect() linking another socket onto connecting_sockets under
connecting_sockets.lock then mutates the same hlist unserialized, which
corrupts the list and desyncs the sk_add_node()/sk_del_node_init()
sock_hold()/__sock_put() pairing. An unprivileged local process holding
LLCP sockets, with the DM supplied by the remote peer over an established
LLCP link, can drive this to leak kernel sockets without bound (the
mis-decrement goes through the non-freeing __sock_put() path, so the
object is never released), leading to memory exhaustion / DoS.
This is the same class of bug that was fixed in the sibling handler
nfc_llcp_recv_cc() by commit b493ea2765cc ("nfc: llcp: Fix use-after-free
race in nfc_llcp_recv_cc()"); recv_dm did not receive the equivalent fix.
Fix it the same way: take lock_sock(), re-check that the socket is still
hashed (release() may have won the race), and for the NOBOUND/REJ case
unlink it from connecting_sockets before moving it to LLCP_CLOSED. The
unlink drops the connecting_sockets membership reference via
sk_del_node_init(), leaving the socket unhashed, so the later
nfc_llcp_sock_unlink() in llcp_sock_release() becomes a no-op and no
double put occurs. |
| In the Linux kernel, the following vulnerability has been resolved:
firewire: cdev: fix back-transition for iso_resource_auto client resource
The todo member of iso_resource_auto structure represents the state of the
client resource and normally transitions in the following order:
ISO_RES_AUTO_ALLOC -> ISO_RES_AUTO_REALLOC -> ISO_RES_AUTO_DEALLOC
However, concurrent access from the work item and the file descriptor
release function can cause the state to transition backwards from
ISO_RES_AUTO_DEALLOC to ISO_RES_AUTO_REALLOC.
Prevent the back-transition by checking the current state before
updating it in the work item. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: riscv: Fix NACL hfence entry update order
The SBI v3.0 specification (section 15.1.2) requires a nested HFENCE
entry to be populated as follows:
1) find an unused entry with Config.Pending == 0
2) update the Page_Number and Page_Count words
3) update the Config word with Config.Pending set
__kvm_riscv_nacl_hfence() writes the Config word first, so the SBI
implementation (or NACL hardware) can observe a pending entry with
pnum/pcount values left over from the previous use of that entry,
resulting in incorrect TLB flush ranges.
Write pnum and pcount first and the Config word last. Since the
consumer is an external agent on coherent shared memory, use
WRITE_ONCE() to stop the compiler from reordering the stores and
smp_wmb() to make the parameter words globally visible before the
Pending bit is set. |
| A vulnerability has been found in diem-project diem up to 5.1.3. This affects an unknown part of the file lib/model/doctrine/PluginDmUser.class.php of the component SHA1 Handler. Such manipulation of the argument salt/password leads to password hash with insufficient computational effort. The attack needs to be performed locally. The attack requires a high level of complexity. It is indicated that the exploitability is difficult. The exploit has been disclosed to the public and may be used. The project was informed of the problem early through an issue report but has not responded yet. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix bpf_sock context code generation
Currently, the ctx access code reads the rx_queue_mapping
field with either a 4-byte or 2-byte load. The rest of the bits
in the register are marked known zero by the verifier. However,
the emitted ctx access code places in the register on certain
the special value (-1) using BPF_MOV_IMM64, which gets sign-extended
to turn on all the bits in the register. By shifting this value right,
the program ends up with a value at runtime above what the verifier
assumes is possible.
Fix this by ensuring the read value is as wide as the assumed size.
Use MOV32 instructions instead of MOV64 instructions to keep
the upper bits zero as assumed by the verifier. Also properly report
the size of the destination variable (the bpf_sock field, 4 bytes) instead
of the source (the socket field, 2 bytes). |
| In the Linux kernel, the following vulnerability has been resolved:
tg3: clean up PHYLIB resources on probe failure
tg3_get_invariants() can register an MDIO bus and connect a PHY for
USE_PHYLIB devices. If tg3_init_one() later fails, its common error path
releases the mappings and netdev without undoing those PHYLIB resources.
Disconnect the PHY and unregister the MDIO bus before the remaining
teardown. Guard PHY cleanup with USE_PHYLIB to match tg3_phy_init(), and
call tg3_mdio_fini() unconditionally to match tg3_mdio_init(). The existing
IS_CONNECTED and MDIOBUS_INITED flags make both helpers safe when
initialization only completed partially.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: Fix dst leak for uncached routes.
ip6_route_output_flags(), ip6_rt_put_flags(), and ip6_dst_check()
detect an uncached route by list_empty(&rt->dst.rt_uncached),
which replaced the static DST_NOCACHE flag check in commit
a4c2fd7f7891 ("net: remove DST_NOCACHE flag").
When a device is unregistered, rt6_uncached_list_flush_dev()
unlinks uncached routes tied to the device from rt6_uncached_list.
Previously, they were moved to another list with list_move()
(__list_del_entry() + list_add()), and since commit 98aa546af5e4
("inet: remove (struct uncached_list)->quarantine"), the routes
are just unlinked with list_del_init().
If list_del_init() runs concurrently, list_empty() evaluates to
true; ip6_route_output_flags() calls dst_hold_safe() incorrectly
and ip6_rt_put_flags() skips ip6_rt_put(), leaking dst, and thus
dev tied via rt->from as well.
The same race is partially fixed by commit 9a6f0c4d5796 ("dst:
fix races in rt6_uncached_list_del() and rt_del_uncached_list()").
Let's check rt6->dst.rt_uncached_list instead.
Note that IPv4 does not have the same issue. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: proximity: pulsedlight: fix iio_device left registered on PM setup failure
pm_runtime_set_active() failing in probe() jumps to error_unreg_buffer,
which only calls iio_triggered_buffer_cleanup() -- it does not undo the
iio_device_register() that already succeeded a few lines above. probe()
then returns the error, the devm-managed indio_dev is freed, but the
iio core still has it registered: the sysfs/chardev nodes stay live and
point at freed memory.
Add an error_unreg_dev label that unregisters the iio device before
falling through to the existing buffer cleanup, mirroring the teardown
order already used in lidar_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: rohm-bu27034: Fix infinite delay on error
When reading an integration-time fails, the code will use error code to
compute the sleep time.
Fix this by using the smallest integration time as a default if
reading fails. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: gp2ap020a00f: drain irq_work after free_irq
The threaded IRQ handler queues data->work through irq_work_queue() so
the trigger is polled from a per-CPU context. free_irq() does not flush
an irq_work the handler already queued, so after gp2ap020a00f_remove()
returns that work may still run and call iio_trigger_poll() on data->trig,
which the devm cleanup has already freed, causing a use-after-free.
Add irq_work_sync(&data->work) after free_irq() in remove() and in the
probe error path, mirroring commit 78601726d4a5 ("iio: trigger: sysfs:
fix use-after-free on remove").
Found by an in-house static analysis tool, confirmed by manual review. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ad4030: fix invalid oversampling_ratio validation
In ad4030_set_avg_frame_len(), the logarithm is calculated before input
validation. Passing zero or negative values leads to an undefined result
from ilog2().
Validate that the input is strictly positive prior to computing its
logarithm. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: kxcjk-1013: reject duplicate event disable
The IIO core does not filter duplicate writes to the event enable
attribute. kxcjk1013_write_event_config() already ignores repeated
enable requests, but a repeated disable request still calls
kxcjk1013_set_power_state(data, false), dropping a runtime PM reference
that was not acquired for this request. This can underflow the runtime
PM usage count and trigger a "Runtime PM usage count underflow" warning.
Return early when the requested state already matches ev_enable_state. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: set info->band for 802.3 encap offload frames
Unlike the 802.11 TX paths, ieee80211_8023_xmit() does not set
info->band from the channel context on non-MLD interfaces. It stays at
0, so ieee80211_get_tx_rates() uses the wrong band for these frames.
Set it the same way as ieee80211_build_hdr(): drop the frame if there is
no channel context, and leave the band at 0 on MLD interfaces. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Nullify "have run CPUs" mask pointer when freeing it
Nullify have_run_cpus when freeing the mask, particularly in the error path
of __sev_guest_init(), so that KVM doesn't have to subtly use sev->active
to track whether or not the mask has been freed. As pointed out by Sashiko,
blindly freeing the mask in sev_vm_destroy() results in a double-free if
the mask is freed if __sev_guest_init() fails.
Throw the logic in a helper as nullifying the pointer is frustratingly
difficult and weird due to have_run_cpus being a single-entry array when
CPUMASK_OFFSTACK=n. Deliberately don't use CPUMASK_VAR_NULL, as it's not
directly assignable when the cpumask is on-stack, e.g. requires using a
local variable and a memcpy(), which is beyond ridiculous. Furthermore,
while clearing the on-stack bitmask is an unnecessary and arguably unwanted
side effect, KVM absolutely relies on '0' being the "null" value given that
the struct is zero-allocated.
Opportunistically add an alloc() helper to pair with free(); there are just
enough call sites to make doing so worthwhile. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: copy the hostid into the ctrl before creating PR pc_refs
Commit 6202783184bf ("nvmet: Improve nvmet_alloc_ctrl() interface and
implementation") added a second uuid_copy() of args->hostid near the end
of nvmet_alloc_ctrl(), and commit 7b658153f1b8 ("nvmet: Remove duplicate
uuid_copy") removed the original copy that sat before
nvmet_ctrl_init_pr() instead of the new one.
Since then nvmet_ctrl_init_pr() snapshots ctrl->hostid into the
per-controller per-namespace reservation refs while the uuid_copy()
from the connect data runs later, after the controller is published.
The ctrl is allocated with kzalloc(), so every pc_ref created on this
path stores the nil UUID.
pc_ref->hostid has a single consumer: nvmet_pr_set_ctrl_to_abort()
matches it against the preempted registrant's hostid to kill and drain
the victim's in-flight I/O for Preempt and Abort. The match can never
hit with the nil UUID, so whenever a namespace with reservations
enabled exists before a host connects, which includes every reconnect,
Preempt and Abort silently degrades into a plain Preempt: the
preempting host sees success while the victim's in-flight I/O is still
in the air.
Copy the hostid where the rest of the connect data is consumed, before
the controller is published and before nvmet_ctrl_init_pr() takes its
snapshot. |
