Export limit exceeded: 412676 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Export limit exceeded: 412676 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (412676 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-98859 | 1 Linux | 1 Linux Kernel | 2026-10-21 | 5.3 Medium |
| In the Linux kernel, the following vulnerability has been resolved: HID: multitouch: stop the release timer from being rearmed on remove mt_remove() quiesces the sticky-finger timer before stopping the hardware: timer_delete_sync(&td->release_timer); sysfs_remove_group(&hdev->dev.kobj, &mt_attribute_group); hid_hw_stop(hdev); timer_delete_sync() waits for a running callback and dequeues the timer, but it does not stop the timer from being armed again. The transport is still delivering reports at that point, and the report path rearms it: if (app->quirks & MT_QUIRK_STICKY_FINGERS) { if (td->mt_io_flags & MT_IO_SLOTS_MASK) mod_timer(&td->release_timer, jiffies + msecs_to_jiffies(100)); A report that arrives after timer_delete_sync() has returned therefore leaves the timer queued. td is allocated with devm_kzalloc() against hdev->dev, so it is freed when the driver is unbound, after mt_remove() returns. When the timer fires afterwards, mt_expired_timeout() dereferences the freed td: struct mt_device *td = timer_container_of(td, t, release_timer); struct hid_device *hdev = td->hdev; if (test_and_set_bit_lock(MT_IO_FLAGS_RUNNING, &td->mt_io_flags)) Simply moving the teardown after hid_hw_stop() does not fix this on its own, because mt_expired_timeout() calls mt_release_contacts(), which walks hdev->inputs; the timer still has to be quiesced before hid_hw_stop() tears the input devices down. Use timer_shutdown_sync() instead, which additionally makes any later mod_timer() a no-op, so neither ordering constraint has to be traded off against the other. This is the final-teardown pattern the function was introduced for, and hid-wiimote already uses it for the same reason. | ||||
| CVE-2026-98857 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ipvs: bound LBLCR and LBLC cache growth ip_vs_lblcr_new() and ip_vs_lblc_new() create cache entries for every previously unseen destination address. The table max_size only tells the periodic collector to reclaim entries after the cache has already exceeded the limit. It does not reclaim entries that the attacker continues to use. Reject new cache entries once either table reaches max_size * 3 / 2. The extra headroom lets the periodic collector catch up while the existing scheduler fallback continues to use the selected destination when cache creation fails. New traffic therefore stays serviceable without growing the tables further. | ||||
| CVE-2026-98856 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: kprobes: Skip disarmed probes when checking optkprobe overlap On x86, an optkprobe at A replaces five bytes with a jump. If a disabled probe B is at A+2, get_optimized_kprobe() stops at B when arming a new probe C at A+4. It leaves A optimized: A A+1 A+2 A+3 A+4 A's jump | e9 | d0 | d1 | d2 | d3 | after C | e9 | d0 | d1 | d2 | cc | The INT3 for C overwrites the last byte of A's jump displacement, so execution can jump to the wrong address. B can have prepared optinsns while disarmed, but has no jump to unoptimize. Continue past disarmed and unprepared probes to find the active optimized probe before arming a probe in its jump. | ||||
| CVE-2026-98855 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: of/overlay: put property on deadprops only after changeset add succeeds add_changeset_property() links a new property of a not-yet-live target node into the node's deadprops list before handing it to of_changeset_add_property(). If that fails, the error path frees the property but leaves the freed pointer linked in deadprops, and of_node_release() frees it a second time when the aborted overlay's node is released. Record the changeset entry first and link the property into deadprops only on success. of_changeset_add_property() never looks at the node's property lists, so the order of the two steps is otherwise immaterial, and the error path frees a property that nothing references. | ||||
| CVE-2026-98854 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: of/overlay: only treat a positive changeset id as registered of_overlay_fdt_apply() stores the idr_alloc() return value in ovcs->id before checking it. On failure the stored id is negative, free_overlay_changeset()'s "if (ovcs->id)" check passes, idr_remove() is called with a negative id and list_del() runs on ovcs->ovcs_list, which is not initialized until after the id allocation. An allocation failure at that point dereferences NULL. Make free_overlay_changeset() treat only a strict-positive id as registered. The rest of the function already copes with a partially-initialized ovcs, so the error path stays a plain goto err_free_ovcs. | ||||
| CVE-2026-98852 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net: extend IPv6 exthdr detection of tunneled packets Commit c4336a07eb6b ("net: correctly handle tunneled traffic on IPV6_CSUM GSO fallback") split skb_gso_has_extension_hdr() into mutually exclusive branches on skb->encapsulation. This did not yet address all paths: 1. With skb->encapsulation set, the outer header is not checked. IPv6 tunnels such as ip6_gre and ip6_tunnel add an outer Destination Options header by default (encap_limit). Their GSO packets skip software GSO, then skb_csum_hwoffload_help() sees the outer extension header and calls skb_checksum_help() on the GSO skb, which warns and drops it. 2. Tunnels over IPv6 without an outer transport header, such as ip6_tunnel, leave skb->transport_header at the inner transport header. skb_network_header_len() then spans the outer IPv6, tunnel and inner IP headers, a false positive. 3. UDP tunnels without an inner network header, such as SCTP-in-UDP or PSP, have no inner IPv6 header to check. Decide on the outer header alone. 4. Directly dereferencing inner_ip_hdr(skb)->version without skb_header_pointer() is unsafe. Instead, check ipv6_ext_hdr(nexthdr) on the outer IPv6 header and, if set, on the inner IPv6 header. Read the headers with skb_header_pointer(). Keep the skb_network_header_len() check when !skb->encapsulation to also catch encapsulated packets without skb->encapsulation (e.g., virtio). Use the same helper in skb_csum_hwoffload_help(). Its open coded test has the false positive of (2) and ignores the inner header. Background: checksum offload of tunneled packets invariants: Non-GSO skb: - If the inner packet is CHECKSUM_PARTIAL, Local Checksum Offload computes the outer checksum in software and the device offloads only the inner L4 checksum. - If the inner packet is CHECKSUM_NONE (e.g., SCTP-in-UDP, ESP-in-UDP, Remote Checksum Offload), the device offloads the outer UDP or GRE checksum instead. GSO skb: - A device with NETIF_F_GSO_UDP_TUNNEL_CSUM or NETIF_F_GSO_GRE_CSUM computes both inner and outer checksums per segment. The outer checksum is seeded with only the pseudo-header checksum. A NETIF_F_IPV6_CSUM device must parse through the outer headers to reach the inner ones. | ||||
| CVE-2026-98851 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_flow_offload: drop flowtable reference on init error path nft_flow_offload_init() bumps the flowtable use count with nft_use_inc() before calling nf_ct_netns_get(). When the latter fails, the error is returned as-is and the reference is leaked. The upper layers do not balance it either: nf_tables_newexpr() clears expr->ops when the expression init callback fails, so the nft_expr_more() iteration in nft_rule_expr_deactivate() and nf_tables_rule_destroy() stops right before the failed expression and its ->destroy callback, which would drop the reference, never runs. Each failed rule addition therefore leaks one flowtable reference and the flowtable can no longer be removed: NFT_MSG_DELFLOWTABLE keeps reporting -EBUSY even though no rule references it. Save the nf_ct_netns_get() return value and undo the nft_use_inc() when it fails, restoring the inc/dec pairing within nft_flow_offload_init() itself. | ||||
| CVE-2026-98850 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net/packet: prevent TX_RING byte count overflow tpacket_snd() drains every SEND_REQUEST frame in a TX ring and adds each valid packet length to the signed int len_sum. Userspace can recycle completed frames concurrently, so a single blocking send call is not bounded by the ring size. After enough successful transmissions len_sum wraps into the negative range. In particular, 65536 65535-byte frames followed by a 65007-byte frame produce 0xfffffdef, or -EIOCBQUEUED. sock_sendmsg_nosec() treats that as an impossible return and triggers a BUG. On systems configured to panic on oops, a CAP_NET_RAW holder can panic the host kernel. Stop before the next frame would make the byte count exceed INT_MAX. The positive short count leaves that frame pending for a later send call. A two-thread TPACKET_V2 reproducer triggered the BUG on an arm64 build of Linux 7.3-rc4. With this change, the same reproducer returned the expected positive short count without an oops. | ||||
| CVE-2026-98848 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: rtc: ac100: Assign .num before accessing .hws Commit f316cdff8d67 ("clk: Annotate struct clk_hw_onecell_data with __counted_by") annotated the hws member of 'struct clk_hw_onecell_data' with __counted_by, which informs the bounds sanitizer (UBSAN_BOUNDS) about the number of elements in .hws[], so that it can warn when .hws[] is accessed out of bounds. As noted in that change, the __counted_by member must be initialized with the number of elements before the first array access happens, otherwise there will be a warning from each access prior to the initialization because the number of elements is zero. This occurs in ac100_rtc_register_clks() due to .num being assigned only after every clkout clock has been stored in .hws[]. With CONFIG_UBSAN_BOUNDS and a compiler that implements __counted_by (GCC 15.1+ or Clang 20.1+), this triggers an array-index-out-of-bounds report during probe, and with CONFIG_UBSAN_TRAP the first store traps. Initialize .num with AC100_CLKOUT_NUM, the number of elements .hws[] was allocated with, right after the allocation. That is the value the loop counter ends up at on the success path anyway, so the provider's behaviour is unchanged. | ||||
| CVE-2026-98847 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: rtc: spear: initialize IRQ state before requesting alarm IRQ devm_request_irq() enables the interrupt before it returns, so the handler may run while probe is still initializing the device. Initialize the MMIO address and spinlock before requesting the alarm IRQ. | ||||
| CVE-2026-98846 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: sctp: check RCV_SHUTDOWN after the sendmsg connect wait sctp_wait_for_connect() drops the socket lock while it sleeps. An out-of-the-blue ABORT can then be processed from the socket backlog and unlink the association. If a concurrent shutdown(fd, SHUT_RD) sets RCV_SHUTDOWN, the waiter breaks with err == 0 before checking asoc->base.dead. Its final sctp_association_put() can then free the association, leaving sctp_sendmsg_to_asoc() to continue with a dangling pointer. Check RCV_SHUTDOWN along with the wait error in sctp_sendmsg_to_asoc() before using the association again. The check only accesses the socket, so it needs no additional association reference. Return the existing -ESRCH so that sctp_sendmsg() skips freeing a new association that may already have been destroyed. Keep sctp_wait_for_connect() unchanged to preserve its behavior for the connect() caller. | ||||
| CVE-2026-98840 | 1 Linux | 1 Linux Kernel | 2026-10-21 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: vc_screen: reload vc pointer before if (ret) in vcs_write() to avoid UAF The reload of 'vc' added by commit 8fb9ea65c9d1 ("vc_screen: reload load of struct vc_data pointer in vcs_write() to avoid UAF") sits after the 'if (ret)' block, so the copy-failure break path exits the loop without reloading vc. If the vc was kfree()'d via vc_port_destruct during the unlocked copy_from_user() window, the post-loop 'if (written && vc) vcs_scr_updated(vc)' is reached with a stale non-NULL vc. The '&& vc' guard from commit a287620312dc ("vc_screen: fix null-ptr-deref in vcs_notifier() during concurrent vcs_write") only handles the NULL case, not this stale-non-NULL case; vcs_notifier() then reads param->vc->vc_num from freed memory: BUG: KASAN: slab-use-after-free in vcs_notifier+0x7c/0xd0 Read of size 2 at addr ffff888007149190 Call Trace: vcs_notifier+0x7c/0xd0 atomic_notifier_call_chain+0x70/0xa0 vcs_scr_updated+0x77/0xa0 vcs_write+0x71b/0x7e0 Allocated by task: vc_allocate -> con_install -> tty_open Freed by task: kfree <- vt_ioctl (VT_DISALLOCATE -> vc_port_destruct) Move the reload to immediately after console_lock(), before 'if (ret)', so every break path below passes a fresh vc to the post-loop vcs_scr_updated(). | ||||
| CVE-2026-98838 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: vt: skip screen update for DEC alignment test on backgroup consoles [BUG] Recently, we encountered a KASAN warning as follows: BUG: KASAN: slab-out-of-bounds in fb_pad_aligned_buffer+0x11f/0x140 Read of size 1 at addr ff1100015fd9f6a4 by task tty_fbcon_oob/1239 CPU: 7 UID: 0 PID: 1239 Comm: tty_fbcon_oob Not tainted 7.3.0-rc1 #100 PREEMPT(full) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014 Call Trace: <TASK> ... kasan_report+0xf0/0x120 fb_pad_aligned_buffer+0x11f/0x140 ccw_putcs+0x86c/0xa80 fbcon_putcs+0x338/0x410 do_update_region+0x21d/0x450 do_con_write+0x1e0e/0x4880 con_write+0x13/0x80 n_tty_write+0x374/0x1010 file_tty_write.isra.0+0x404/0x7a0 ... reproduce: 1) open /dev/tty0, set a KDFONTOP ioctl with op.op = KD_FONT_OP_SET, op.width = 8 and op.height = 16 (visible VC1) 2) open /dev/tty1, set a KDFONTOP ioctl with op.op = KD_FONT_OP_SET, op.width = 28 and op.height = 24 (invisible VC2) 3) echo 3 > /sys/devices/virtual/graphics/fbcon/rotate_all 4) write EShash8(esc hash8) to tty1 [CAUSE] All VCs render to the framebuffer. setfont only modifies the target VC's font without resizing the framebuffer backing buffer (par->rotated.buf); the buffer is only resized for the visible VC (fbcon_do_set_font -> ... -> vc_do_resize -> update_screen). This relies on the con_should_update() check performed before every update_region(). However, the ESC # 8 path (do_con_trol -> do_update_region) omits the con_should_update() check. After changing the font size of an invisible VC, do_update_region() fills using the new font size against a buffer that was never resized, causing an out-of-bounds access. [FIX] Only push the update when the console is visible and not blanked, add the con_should_update() check in the do_con_trol() like every other call site of do_update_region() (update_region(), invert_screen(), ...). | ||||
| CVE-2026-98837 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: caiaq: unregister the input device when probe fails setup_card() registers the input device, whose name and phys point into struct snd_usb_caiaqdev, and then goes on to snd_card_register() and snd_usb_caiaq_control_init(). If either fails, snd_probe() calls snd_card_free(), which frees the device state but leaves the input device registered: card_free() only clears the pointer, and the input device is unregistered from snd_disconnect() alone. Reading its "uevent" attribute afterwards dereferences freed memory: BUG: KASAN: slab-use-after-free in string+0x4a9/0x4f0 Read of size 1 at addr ffff8880208f5043 by task caiaq/4967 add_uevent_var+0x183/0x3a0 input_dev_uevent+0x162/0x900 dev_uevent+0x2f1/0x870 uevent_show+0x1ca/0x3a0 ... Unregister the input device on the probe error path, as snd_disconnect() does. snd_usb_caiaq_input_disconnect() is a no-op when no input device was registered. Reproduced with a raw-gadget Audio Kontrol 1 and a temporary hack that makes snd_usb_caiaq_control_init() fail. | ||||
| CVE-2026-98836 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: line6: reject oversized playback packets Each playback URB is handed a slice of out.buffer that is exactly LINE6_ISO_PACKETS * max_packet_size_out bytes, sized from the OUT endpoint, but the number of bytes written into that slice is never compared against it. submit_audio_out_urb() takes the frame count from prev_fsize, which audio_in_callback() derived from the *IN* endpoint's received packet length, and rescales it with the playback frame size; when prev_fsize is still zero it synthesizes a length from the sample rate instead. On a device declaring a large IN wMaxPacketSize and a small OUT wMaxPacketSize, the resulting memcpy(), or the memset() when the playback stream is idle, runs past its slice and, as the reproducer below shows, beyond the allocation. usb_submit_urb() is not a backstop. max_packet_size_out comes from usb_maxpacket(), which returns only the low 11 bits of wMaxPacketSize, while USB core validates a high-speed isochronous length against that base scaled by usb_endpoint_maxp_mult(). A length of up to three times the allocated slice is therefore accepted, and even a rejected URB is only rejected after the write. Reject a packet that does not fit the slice the driver allocated for it. Clamping it instead would silently shorten the capture-derived rate feedback and desynchronize the two streams. BUG: KASAN: slab-out-of-bounds in submit_audio_out_urb (sound/usb/line6/playback.c:229) Write of size 1024 at addr ffff888100bbd400 by task kworker/1:2/5002 Workqueue: events line6_startup_work Call Trace: __asan_memcpy (mm/kasan/shadow.c:106) submit_audio_out_urb (sound/usb/line6/playback.c:229) line6_submit_audio_out_all_urbs (sound/usb/line6/playback.c:291) line6_stream_start (sound/usb/line6/pcm.c:194) line6_pcm_acquire (sound/usb/line6/pcm.c:337) line6_startup_work (sound/usb/line6/driver.c:728) process_one_work (kernel/workqueue.c:3396) worker_thread (kernel/workqueue.c:3479 kernel/workqueue.c:3560) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245) The buggy address belongs to the object at ffff888100bbd400 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 0 bytes inside of allocated 256-byte region [ffff888100bbd400, ffff888100bbd500) | ||||
| CVE-2026-98835 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: iio: accel: kionix-kx022a: Fix array boundary check The driver performs a sanity check for an array size, when converting a register value to an array index. The check incorrectly accepts the sizeof(array) as a last index, when last valid index should be sizeof(array) - 1. Fix the check by bailing out when index >= sizeof(array). | ||||
| CVE-2026-98833 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: mtd: core: call _get_device() with the master MTD __get_mtd_device() calls the master's _get_device() callback with mtd, which may be a partition. __put_mtd_device() passes the master. This breaks gluebi partitions because gluebi_get_device() uses container_of() and therefore requires the master MTD. Pass the master to _get_device(), matching _put_device(). | ||||
| CVE-2026-98831 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: of/overlay: don't leak fragment references when changeset init fails init_overlay_changeset() stores the number of initialized fragments in ovcs->count only on full success. When find_target() or the __symbols__ lookup fails partway through, the target and overlay references taken for the fragments initialized so far are never dropped: free_overlay_changeset() bounds its cleanup loop by ovcs->count, which is still 0. Store the running count on the error path so free_overlay_changeset() puts whatever was set up. The store is guarded by ovcs->fragments because on the allocation-failure path cnt still holds the counting pass total while there is no fragments array; everywhere else cnt only counts fully-initialized fragments. | ||||
| CVE-2026-98830 | 1 Linux | 1 Linux Kernel | 2026-10-21 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: wfx: validate MIB read length before copying to caller wfx_hif_read_mib() copies reply->length bytes from the firmware response into the caller-provided buffer without checking that reply->length does not exceed val_len. A firmware response with a length field larger than expected overruns the caller buffer and reads past the end of the reply allocation. Replace the dead -ENOMEM check with an active validation that reply->length fits within val_len before the memcpy. | ||||
| CVE-2026-98825 | 1 Linux | 1 Linux Kernel | 2026-10-21 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: rtc: mpfs: fix unchecked devm_clk_get() error pointer in probe() devm_clk_get(&pdev->dev, "rtcref")'s return value was passed straight into clk_get_rate() without checking it for an error first, unlike the "rtc" clock a few lines above which is correctly checked with IS_ERR(). clk_get_rate() only guards against a NULL clk, not an error pointer: if (!clk) return 0; ... rate = clk_core_get_rate_recalc(clk->core); so if devm_clk_get() ever returns an error pointer here (for example ERR_PTR(-EPROBE_DEFER), which is the normal, expected outcome if the clkcfg clock-provider this RTC depends on has not registered its clocks yet by the time this driver probes), clk_get_rate() dereferences that error pointer instead of returning 0, crashing instead of letting probe defer. Capture the clock in the existing 'clk' local and check it with IS_ERR() before calling clk_get_rate(), matching the handling already used for the "rtc" clock in this same function. | ||||