| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net/packet: guard the ll header push in packet_rcv_spkt()
packet_rcv_spkt() restores the link layer header with
skb_push(skb, skb->data - skb_mac_header(skb));
That subtraction is only meaningful when the device actually has a link
layer header. packet_rcv() and tpacket_rcv() both wrap it in
dev_has_header(), which is also the predicate the block comment at the
top of the file states the restore in terms of; packet_rcv_spkt() does
not. commit d549699048b4 ("net/packet: fix packet receive on L3
devices without visible hard header") introduced the helper and changed
the two call sites, and this one stayed behind.
A device without a visible ll header can leave skb->mac_header at the
0xFFFF sentinel that __alloc_skb() initialises it to. A CAN skb does:
init_can_skb() sets pkt_type and ip_summed but does not reset the
headers, and commit 9f10374bb024 ("can: remove private CAN skb
headroom infrastructure") dropped the skb_reset_*_header() calls that
used to be there. skb_mac_header() is then 0xFFFF, the length becomes
a large negative number and skb_push() reports it through
skb_under_panic() -- from softirq context, so it is a full system panic
even with panic_on_oops=0:
skbuff: skb_under_panic: text:ffffffff8bd21bc1 len:-65455 put:-65471 head:... data:... tail:0x50 end:0x180 dev:can0
kernel BUG at net/core/skbuff.c:214!
RIP: 0010:skb_panic+0x50/0x60
Call Trace:
<IRQ>
skb_push+0x38/0x40
packet_rcv_spkt+0xe1/0x170
__netif_receive_skb_core.constprop.0+0x7e8/0xd30
...
Kernel panic - not syncing: Fatal exception in interrupt
The socket type is reachable: packet_create() accepts SOCK_PACKET
alongside SOCK_RAW and SOCK_DGRAM behind the same CAP_NET_RAW check,
and neither the socket length nor a capability check keeps it away
from a CAN interface.
The missing skb_reset_*_header() calls in init_can_skb() are a
regression in their own right and are being fixed separately, but a
packet socket should not turn a link layer that did not initialise its
mac header into a kernel panic. Guard the push the way the other two
receive paths do.
Tested on v7.3-rc5 under QEMU with a slcan device on a pty, which is
the driver RX path: vcan does not reproduce it, because can_send()
resets the headers on the way out. One SOCK_PACKET socket bound to
can0 and one frame written into the line discipline panics an
unpatched kernel with the trace above; the same image with this patch
prints no panic and powers off normally. Both kernels are this tree,
defconfig plus CONFIG_CAN_SLCAN=y, differing only in this hunk. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: sdhci-sprd: disable runtime PM on remove
sdhci_sprd_probe() enables runtime PM, while sdhci_sprd_remove() does
not perform the corresponding runtime PM cleanup.
The probe failure path disables runtime PM before disabling the clocks,
but the normal remove path directly disables clocks that are also
managed by the runtime PM callbacks. If the device is runtime
suspended, those clocks may already be disabled.
Resume the device before removal, disable runtime PM and drop the
temporary runtime PM reference before disabling the clocks.
This issue was found by manual code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-crypt: reject the lmk IV mode with AEAD ciphers
A "capi:" table line that pairs an AEAD cipher with the lmk IV mode,
for example "capi:gcm(aes)-lmk" with the integrity:28:aead option,
causes an oops when it is loaded. lmk sets tfms_count to 64, but
crypt_alloc_tfms_aead only allocates one transform, so crypt_setkey
reads past the end of the tfms_aead array and calls crypto_aead_setkey
on the values it finds there.
lmk exists for compatibility with Loop-AES, which uses CBC, so refuse
it with an AEAD cipher rather than allocate 64 AEAD transforms. The
check cannot go in crypt_iv_lmk_ctr with the other lmk checks, because
the IV constructor runs after crypt_set_key.
Note that this is not a security bug because the memory corruption can
only be triggered by root. |
| In the Linux kernel, the following vulnerability has been resolved:
memstick: core: wait for request completion before freeing card
In memstick_alloc_card() and memstick_set_rw_addr(),
wait_for_completion_timeout() is used to wait for device identification
and address configuration requests to complete.
The memstick subsystem does not provide an abort or cancellation
callback in struct memstick_host for in-flight requests. If
wait_for_completion_timeout() expires (for instance, when a USB transfer
or command retry is delayed), memstick_alloc_card() returns an error and
frees the memstick_dev structure via kfree(card).
However, the host controller driver (such as rtsx_usb_ms) is still
running the request asynchronously in worker context. When the transfer
eventually finishes, the driver writes into host->req->data, which
points to memory inside the already freed card structure. This leads to
a KASAN slab-use-after-free write:
BUG: KASAN: slab-use-after-free in ms_read_bytes+0x8fe/0x990
Write of size 1 at addr ffff88813c188079 by task kworker/1:5/5239
Workqueue: events rtsx_usb_ms_handle_req
Call Trace:
ms_read_bytes+0x8fe/0x990 drivers/memstick/host/rtsx_usb_ms.c:450
rtsx_usb_ms_issue_cmd drivers/memstick/host/rtsx_usb_ms.c:477 [inline]
rtsx_usb_ms_handle_req+0x557/0x1a00 drivers/memstick/host/rtsx_usb_ms.c:531
process_one_work+0xac7/0x1b10 kernel/workqueue.c:3396
worker_thread+0x5ef/0xe50 kernel/workqueue.c:3560
kthread+0x373/0x450 kernel/kthread.c:436
Allocated by task 1662:
memstick_alloc_card drivers/memstick/core/memstick.c:383 [inline]
memstick_check+0x2c1/0x10d0 drivers/memstick/core/memstick.c:452
process_one_work+0xac7/0x1b10 kernel/workqueue.c:3396
Freed by task 1662:
kfree+0x20c/0x650 mm/slub.c:6792
memstick_alloc_card drivers/memstick/core/memstick.c:420 [inline]
memstick_check+0x72b/0x10d0 drivers/memstick/core/memstick.c:452
process_one_work+0xac7/0x1b10 kernel/workqueue.c:3396
Host controller drivers (rtsx_usb_ms, jmb38x_ms, tifm_ms, r592) already
implement their own hardware and bus timeouts, and callers in
mspro_block and ms_block already rely on wait_for_completion()
unconditionally.
Replace wait_for_completion_timeout() with wait_for_completion() in
memstick_set_rw_addr() and memstick_alloc_card() so that the card
structure is never freed while an asynchronous request is in flight. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: validate deauth frame length before reason access
ieee80211_rx_mgmt_deauth() reads the deauth reason code before checking
that the fixed field is actually present in the received frame.
Validate the deauth frame length first and only then read the reason
code. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Validate BASE_ERROR_EVENT payload size
BASE_ERROR_EVENT carries a variable number of message reports,
with the count encoded in error_status. The notification parser used
that count without checking whether the received payload contained all
reported entries.
Reject truncated payloads before copying the report array. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Validate SENSOR_UPDATE payload size
SENSOR_UPDATE carries one or more sensor readings after the fixed
notification header. The parser derives the expected reading count
from the sensor description, but it did not verify that the received
payload contains those entries before parsing them.
Reject truncated update notifications before reading the variable
array. |
| In the Linux kernel, the following vulnerability has been resolved:
xen/gntalloc: validate grant count before allocation
gntalloc_ioctl_alloc() allocates the grant-id array before checking
whether the requested count fits within the global grant limit. Counts
above that limit cannot succeed, so reject them before the
user-controlled allocation reaches kcalloc().
Use a subtraction-based check while holding gref_mutex so adding the
requested count cannot wrap. Also cast the count before advancing the
per-file index so the page-size multiplication is performed in 64-bit
arithmetic. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix lease break and ack state handling
Do not skip valid lease states containing WRITE_CACHING when breaking
level-II/read leases for writes and truncates.
Handle lease break acknowledgments according to the SMB2 rule that the
acknowledged state must be a subset of the server's break target. Apply
the acknowledged state directly and keep the break pending on failed ACKs. |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: imx: Add a channel shutdown field
sashiko complained about possible teardown problem. The scenario
CPU 0 CPU 1
imx_mu_isr() imx_mu_shutdown()
imx_mu_xcr_rmw(priv, IMX_MU_RCR, 0, IMX_MU_xCR_RIEn(priv->dcfg->type, cp->idx));
imx_mu_specific_rx()
imx_mu_xcr_rmw(priv, IMX_MU_RCR, IMX_MU_xCR_RIEn(priv->dcfg->type, 0), 0);
free_irq()
The RX event remains enabled because in this short window the RX event
was disabled in ->shutdown() while the interrupt was active and then
enabled again by the ISR while ->shutdown waited in free_irq().
This race requires timing and if happens can be problematic on shared
handlers if the "removed" channel triggers an interrupt. In this case
the irq-core will shutdown the interrupt with the "nobody cared"
message.
Introduce imx_mu_con_priv::shutdown to signal that the channel is
shutting down. This flag is set with the lock held (by
imx_mu_xcr_clr_shut()). The unmask side uses imx_mu_xcr_set_act() which
only enables the event if the channel has not been shutdown and
serialises on the same lock. |
| Vitess is a database clustering system for horizontal scaling of MySQL. Prior to 23.0.5 and 24.0.2, twopczHandler in go/vt/vttablet/tabletserver/twopcz.go writes the Action and dtid form values from the vttablet and vtcombo /twopcz HTTP debug endpoint into a text/html response without HTML escaping. Under the default allow-all ACL policy, a remote unauthenticated attacker can send an operator a crafted request that executes script in the operator's browser after the request is opened. The script runs with the vttablet debug origin and can read same-origin diagnostic endpoints that expose query, transaction, environment, variable, or profiling data available in that deployment. This issue is fixed in versions 23.0.5 and 24.0.2. |
| Backstage is an open framework for building developer portals. Prior to 4.1.0, the @backstage/plugin-scaffolder-backend package is affected by incorrect authorization in scaffolder task listing. An authenticated internal user may be able to view metadata for scaffolder tasks outside the visibility intended by a deployment's permission policy. Stored task secrets are not included in the affected response, and no integrity or availability impact was identified. This issue is fixed in version 4.1.0. |
| Backstage is an open framework for building developer portals. Prior to 0.3.10 in @backstage/plugin-scaffolder-backend-module-bitbucket-cloud and 0.2.25 in @backstage/plugin-scaffolder-backend-module-bitbucket-server, the Bitbucket pull-request Scaffolder actions did not sufficiently validate filesystem paths. An authenticated user who can execute an eligible template and influence an allowed Bitbucket repository could affect paths outside the expected working area, potentially compromising backend confidentiality, integrity, or availability. This issue is fixed in @backstage/plugin-scaffolder-backend-module-bitbucket-cloud 0.3.10 and @backstage/plugin-scaffolder-backend-module-bitbucket-server 0.2.25. |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: imx: Use devm_pm_runtime_enable()
sashiko complained about early usage of the device while probe isn't
completed. This can be mitigated by delaying the pm_runtime_enable()
into the removal path instead doing it early. This ensures that in an
error case the device is removed (and imx_mu_shutdown()) before
pm_runtime_disable() so we don't have to do this manually.
For the order to work, lets move devm_mbox_controller_register() until
after the pm-runtime part. So the reverse order will be mbox-controller
removal followed by disabling pm runtime.
Use devm_pm_runtime_enable(), remove manual pm_runtime_disable()
invocations and move the pm_runtime handling in probe before
devm_mbox_controller_register(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Properly acquire queue buffers in CRIU restore
When kfd_queue_acquire_buffers() was split off from
set_queue_properties_from_user(), set_queue_properties_from_criu()
was missed. Thus, set_queue_properties_from_criu() is not
filling out the buffer fields of queue_properties, which
can come up when subsequent code expects them to be non-null.
Add the proper call to kfd_queue_acquire_buffers(), and also
use the right cast types in set_queue_properties_from_criu()
(which were missed at the same time)
(cherry picked from commit 88ed96abbbe27b70193544fbc1ee06448c274714) |
| In the Linux kernel, the following vulnerability has been resolved:
namespace: don't let a pseudo dentry become the root of a mount
d_alloc_pseudo() hands out dentries for pipes, sockets and other files
that are never anyone's child or parent. They carry DCACHE_NORCU and
dentry_free() frees them right away because no lockless path walk can
ever reach them. That holds as long as such a dentry isn't the root of
a mount. But bind mounting /proc/self/fd/<fd> of such a file does
exactly that.
Most callers of alloc_file_pseudo() put their files on kernel-internal
mounts and may_copy_tree() refuses those. bpf_token_create() doesn't. It
places the token file on the bpffs mount the caller handed it and that
mount is in the caller's mount namespace so the clone goes through:
mount --bind /proc/self/fd/<token> <file>
open_tree(tokfd, "", AT_EMPTY_PATH | OPEN_TREE_CLONE) + move_mount()
__follow_mount_rcu() then loads ->mnt_root of that mount, reads d_seq
and d_flags of the dentry and only then checks mount_lock. The dentry
can be gone by then. The final mntput() of an unmounted parent unhooks
a child that stayed attached to it under mount_lock alone. When the
child's holder does the final put right after that the root is dput()
and freed immediately while a walker that found the mount hashed still
looks at it.
Refuse to clone a mount with a DCACHE_NORCU dentry as its root. Nothing
sensible can be done with a bind mount of a bpf token anyway. |
| In the Linux kernel, the following vulnerability has been resolved:
namespace: check the mounts before reading their parents in pivot_root()
path_pivot_root() reads the parents of new_root and of the caller's root
and checks whether they are shared before it checks that either mount is
in the caller's mount namespace. Only namespace_sem is held. That's fine
for a mount that is in the caller's mount namespace.
But new_root can be a file descriptor to a mount that has been unmounted
and that only the file descriptor keeps alive. If that mount stayed
attached to its parent when it was unmounted nothing pins the parent for
it. The final mntput() of the parent unhooks the children under
mount_lock alone and frees the parent afterwards:
pivot_root() close(fd), last ref on the parent
------------ ---------------------------------
ex_parent = new_mnt->mnt_parent
mntput_no_expire_slowpath()
__umount_mnt(new_mnt)
cleanup_mnt()
call_rcu()
IS_MNT_SHARED(ex_parent)
BUG: KASAN: slab-use-after-free in path_pivot_root+0xf1a/0x1840
Read of size 4 at addr ffff8881047382f8 by task pivot_widen/157
path_pivot_root+0xf1a/0x1840
__x64_sys_pivot_root+0x165/0x190
The same goes for the caller's root via chroot(). Both outcomes of the
check end in EINVAL so nothing but the read itself goes wrong. It's the
same thing commit bb4609405752 ("statmount: read the parent of an
unmounted mount under mount_lock") fixed for statmount().
Check that both mounts are in the caller's namespace before their
parents are read. Every path returns EINVAL either way. |
| A Signed to Unsigned Conversion Error vulnerability in the srxpfe of Juniper Networks Junos OS on the SRX Series allows an adjacent attacker to cause a denial of service of the data plane via chassis-cluster fabric traffic. |
| An Integer Underflow (Wrap or Wraparound) vulnerability in the rpd process of Juniper Networks Junos OS on EX Series and MX Series, and Junos OS Evolved on ACX Series allows an unauthenticated adjacent attacker to cause heap memory disclosure and multicast join-state injection via a malformed Rosen-MVPN message.
This issue only affects platforms that support draft Rosen MVPN, such as the ACX Series, EX Series, and MX Series. |
| Loop with Unreachable Exit Condition ('Infinite Loop') vulnerability in Erlang OTP stdlib (erl_tar module), hexpm hex_core (hex_erl_tar module), hexpm hex (mix_hex_erl_tar module) and erlang rebar3 (r3_hex_erl_tar module) allows an attacker who supplies a tar archive to cause a denial of service via a crafted GNU sparse member.
When erl_tar:extract/1,2 writes a member to disk, erl_tar:stream_to_file_loop/3 reads it in chunks of 65536 bytes by default. For a GNU sparse member whose sparse map ends before its real size, erl_tar:do_sparse_read/3 matches its trailing-hole clause before its zero-length clause. After the chunk is used up, the trailing-hole clause reads zero bytes, does not advance the position, and recurses forever. A 2048-byte archive keeps the extracting process and one scheduler busy until the process is killed. The {max_size, N} option prevents this only when N is below the real size of the member. Extraction with the memory option is not affected.
hex_core ships its own copy of erl_tar as hex_erl_tar, and Hex and rebar3 ship hex_core with prefixed module names (mix_hex_erl_tar and r3_hex_erl_tar). These copies contain the same code and do not call stdlib's erl_tar, so they are affected on any OTP version. OTP 28 is not affected, but an application running on OTP 28 is affected if it extracts archives through an affected version of hex_core, Hex or rebar3.
This issue affects OTP from OTP 29.0 before OTP 29.1.2, corresponding to rebar3 from 3.27.1 before 3.28.0, and stdlib from 8.0 before 8.1.1, and hex from 2.4.2 before 2.5.3; hex_core: from 0.14.0 before 0.20.1. |
