| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mac802154: hold an interface reference across the scan worker
mac802154_scan_worker() captures the scanning sub-interface under RCU
and then keeps dereferencing sdata->dev after rcu_read_unlock() and
outside the rtnl -- in the failure traces, in
mac802154_transmit_beacon_req() (skb->dev = sdata->dev), and in the
end_scan cleanup. Nothing keeps that netdev alive across the worker
iteration.
A concurrent DEL_INTERFACE or PHY removal can unregister the interface
once the worker drops the rtnl between its two drv_set_channel()
sections. unregister_netdevice() frees the netdev asynchronously from
netdev_run_todo() with the rtnl already dropped, so neither holding the
rtnl nor the per-PHY IEEE802154_IS_SCANNING flag prevents a stale worker
iteration from dereferencing the freed netdev -- a KASAN
slab-use-after-free, reachable by racing TRIGGER_SCAN against
DEL_INTERFACE (both CAP_NET_ADMIN).
Pin the netdev with netdev_hold() while the RCU read lock is still held,
and release it at every worker exit. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: avoid putting unrelated P2P peer on socket release
ovpn_peer_release_p2p() is called when an OVPN UDP socket is being
destroyed. It checks the currently published P2P peer and releases it only
if that peer still uses the socket being destroyed.
A peer replacement can publish a new peer before the old UDP socket is
destroyed. When the old socket destruction path runs afterwards,
ovpn_peer_release_p2p() observes the new peer through ovpn->peer. Since the
new peer uses a different socket, the function takes the socket mismatch
branch.
That branch still calls ovpn_peer_put(peer). At this point, however, peer
is the currently published replacement peer, not the peer associated with
the socket being destroyed. Dropping its reference can free it while
ovpn->peer still points to it, leading to later use-after-free accesses
from the peer and socket cleanup paths.
KASAN reports this as a slab-use-after-free on the kmalloc-1k ovpn_peer
object. In the reproducer, the object is allocated from ovpn_peer_new() via
ovpn_nl_peer_new_doit(), and freed through ovpn_peer_release_rcu() from RCU
callback processing. Observed access sites include ovpn_peer_remove(),
ovpn_socket_release(), ovpn_nl_peer_del_notify(), and unlock_ovpn().
Fix this by returning from the socket mismatch branch without putting the
peer. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: core: port: Deattach Type-C connector on component unbind
connector_unbind() is the mirror of connector_bind(), but it is missing
the symmetric call to typec_deattach() that connector_bind() makes via:
if (port_dev->child)
typec_attach(port_dev->connector, &port_dev->child->dev);
When a Thunderbolt dock is unplugged, two teardown paths race:
1. The component framework calls connector_unbind() first, which sets
port_dev->connector = NULL without calling typec_deattach(). This
leaves port->usb2_dev/port->usb3_dev in struct typec_port pointing at
the USB device that is about to be freed.
2. usb_disconnect() then calls typec_deattach(port_dev->connector, ...),
but port_dev->connector is already NULL, so the call is a no-op and
port->usb2_dev is never cleared.
3. Concurrently, UCSI detects a PD partner-disconnect event and calls
typec_unregister_partner(), which reads port->usb2_dev (now a dangling
pointer to freed memory) and passes it to typec_partner_unlink_device()
-> sysfs_remove_link() -> dev_name() on the freed device, corrupting
the typec/UCSI partner state.
This corruption leaves the Thunderbolt tunnel in an inconsistent state on
the next dock hot-plug. On affected hardware the dock's I225/igc NIC fails
to enumerate: AER fires a slot reset while the igc driver is still
initialising ("PCIe link lost"), and the subsequent igc_reset attempt hits
igc_rd32 on an already-detached device:
igc 0000:2e:00.0 eth0: PCIe link lost, device now detached
igc: Failed to read reg 0x0!
WARNING: CPU: 9 PID: 129 at drivers/net/ethernet/intel/igc/igc_main.c:7005
igc_rd32+0xa4/0xc0 [igc]
Call Trace:
igc_disable_pcie_master+0x16/0xa0 [igc]
igc_reset_hw_base+0x14/0x170 [igc]
igc_reset+0x63/0x110 [igc]
igc_io_slot_reset+0x9e/0xd0 [igc]
report_slot_reset+0x5d/0xc0
pcie_do_recovery+0x209/0x400
aer_isr_one_error_type+0x235/0x430
aer_isr+0x4e/0x80
irq_thread+0xf4/0x1f0
4. UCSI later handles the PD partner-disconnect and calls
typec_unregister_partner(), which still sees the stale port->usb2_dev
and tries to remove its sysfs link a second time:
kernfs: can not remove 'typec', no directory
WARNING: CPU: 6 PID: 55 at fs/kernfs/dir.c:1706 kernfs_remove_by_name_ns+0xe9/0xf0
Workqueue: events ucsi_handle_connector_change [typec_ucsi]
Call Trace:
sysfs_remove_link+0x19/0x50
typec_unregister_partner+0x6e/0x120 [typec]
ucsi_unregister_partner+0x107/0x150 [typec_ucsi]
ucsi_handle_connector_change+0x3ec/0x490 [typec_ucsi]
process_one_work+0x18e/0x3e0
worker_thread+0x2e3/0x420
kthread+0x10a/0x230
ret_from_fork+0x121/0x140
ret_from_fork_asm+0x1a/0x30
With worse timing the same stale pointer is dereferenced after the
backing memory is freed, turning the warning into a use-after-free.
Fix the asymmetry: call typec_deattach() before clearing
port_dev->connector, matching what connector_bind() does on the bind side.
typec_partner_deattach() is already protected by port->partner_link_lock,
so it serialises safely with the concurrent typec_unregister_partner() path. |
| In ssh in OpenSSH before 10.5, a use-after-free for realloc data can occur if a certain pair of remote-forwarding operations are concurrent. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: virt_concat: fix use-after-free in mtd_virt_concat_destroy()
mtd_concat_destroy() frees item->concat so calling
mtd_virt_concat_put_mtd_devices(item->concat) after that leads to a
use-after-free.
Fix it by moving mtd_virt_concat_put_mtd_devices() before
mtd_concat_destroy(). |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nzxt-kraken3) Stop device IO before calling hid_hw_stop
Calling hid_hw_stop() does not stop the device IO.
This results in a race condition between hid_input_report() and the point
immediately following the execution of hid_device_io_start() within
the driver probe function. If the probe operation fails after "io start"
has been initiated, this race condition will result in a UAF vulnerability.
Fix the problem by calling hid_device_io_stop() before calling
hid_hw_stop(). |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix use-after-free on workqueue during remove
In pdsc_remove(), the workqueue is destroyed before pdsc_teardown()
is called. This ordering allows two paths to queue work on the
destroyed workqueue:
1. If pdsc_teardown() -> pdsc_devcmd_reset() times out, the error
path in pdsc_devcmd_locked() queues health_work.
2. A NotifyQ event can trigger the ISR and queue work before free_irq()
is called in pdsc_teardown().
Fix by moving destroy_workqueue() after pdsc_teardown() so the
workqueue outlives every queuer; destroy_workqueue() then flushes any
work still pending.
Draining the queued work also requires ordering the teardown so the
resources that work touches are freed last:
- In pdsc_qcq_free(), after freeing the interrupt, cancel_work_sync()
the queue's work and only then clear qcq->intx, so
pdsc_process_adminq()'s read of qcq->intx for interrupt-credit
return cannot race with the clear.
- Free adminqcq before notifyqcq: the shared adminq ISR is released
when adminqcq is freed, and the adminq work accesses notifyqcq, so
both must be stopped before notifyqcq is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: Avoid use-after-free in fuse_uring_async_stop_queues
fuse_uring_async_stop_queues() might run when the last reference
on ring->queue_refs was already dropped.
In order to avoid an early destruction a reference on struct fuse_conn
is now taken before starting fuse_uring_async_stop_queues() and that
reference is only released when that delayed work queue terminates. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: isci: Fix use-after-free in device removal path
The ISCI completion tasklet is initialized in isci_host_alloc()
(drivers/scsi/isci/init.c:496) and scheduled from both MSI-X and legacy
interrupt handlers (drivers/scsi/isci/host.c:223,613).
isci_host_deinit() stops the controller and waits for stop completion,
but it never kills completion_tasklet before teardown continues. A
top-of-function tasklet_kill() is not sufficient here: interrupts are
only disabled when isci_host_stop_complete() runs, so until
wait_for_stop() returns the IRQ handlers can still requeue the
tasklet. The tasklet callback also re-enables interrupts after draining
completions, so killing the tasklet before the source is quiesced leaves
the same race open.
Once wait_for_stop() returns, no further IRQ-driven scheduling can
occur. Kill completion_tasklet there so teardown cannot race a queued
tasklet running on a dead ihost. On remove or unload, the stale callback
can otherwise dereference ihost and touch ihost->smu_registers after the
host lifetime ends.
A UML + KASAN analogue reproduced the failure class both with no
tasklet_kill() and with tasklet_kill() placed before source quiesce, and
stayed clean once the kill happened after quiescing the scheduling
source.
This mirrors commit f6ab594672d4 ("scsi: aic94xx: fix use-after-free in
device removal path"), but ISCI needs the kill after wait_for_stop(). |
| Use after free in Views in Google Chrome prior to 151.0.7922.109 allowed a remote attacker who convinced a user to engage in specific UI gestures to potentially exploit heap corruption via a crafted HTML page. (Chromium security severity: High) |
| Use after free in HTML in Google Chrome prior to 151.0.7922.109 allowed a remote attacker to potentially exploit heap corruption via a crafted HTML page. (Chromium security severity: High) |
| In the Linux kernel, the following vulnerability has been resolved:
net: qualcomm: rmnet: fix endpoint use-after-free in rmnet_dellink()
rmnet_dellink() removes the endpoint from the hash table with
hlist_del_init_rcu() and then immediately frees it with kfree(). However,
RCU readers on the receive path (rmnet_rx_handler ->
__rmnet_map_ingress_handler) may still hold a reference to the endpoint and
dereference ep->egress_dev after the memory has been freed. The endpoint is
a kmalloc-32 object, and the stale read at offset 8 corresponds to the
egress_dev pointer.
BUG: unable to handle page fault for address: ffffffffde942eef
Oops: 0002 [#1] SMP NOPTI
CPU: 1 UID: 0 PID: 137 Comm: poc_write Not tainted 7.0.0+ #4 PREEMPTLAZY
RIP: 0010:rmnet_vnd_rx_fixup (rmnet_vnd.c:27)
Call Trace:
<TASK>
__rmnet_map_ingress_handler (rmnet_handlers.c:48 rmnet_handlers.c:101)
rmnet_rx_handler (rmnet_handlers.c:129 rmnet_handlers.c:235)
__netif_receive_skb_core.constprop.0 (net/core/dev.c:6096)
__netif_receive_skb_one_core (net/core/dev.c:6208)
netif_receive_skb (net/core/dev.c:6467)
tun_get_user (drivers/net/tun.c:1955)
tun_chr_write_iter (drivers/net/tun.c:2003)
vfs_write (fs/read_write.c:688)
ksys_write (fs/read_write.c:740)
</TASK>
Add an rcu_head field to struct rmnet_endpoint and replace kfree() with
kfree_rcu() so the endpoint memory remains valid through the RCU grace
period. Also remove the rmnet_vnd_dellink() call and inline only the
nr_rmnet_devs decrement, since rmnet_vnd_dellink() would set
ep->egress_dev to NULL during the grace period, creating a data race
with lockless readers. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: bla: fix report_work leak on backbone_gw purge
batadv_bla_purge_backbone_gw() removes stale backbone gateway entries,
but fails to properly handle their associated report_work:
- If report_work is running, the purge must wait for it to finish before
freeing the backbone_gw, otherwise the worker may access freed memory
(e.g. bat_priv).
- If report_work is pending, the purge must cancel it and release the
reference held for that pending work item.
The previous implementation called hlist_for_each_entry_safe() inside a
spin_lock_bh() section, but cancel_work_sync() may sleep and therefore
cannot be called from within a spinlock-protected region.
Restructure the loop to handle one entry per spinlock critical section:
acquire the lock, find the next entry to purge, remove it from the hash
list, then release the lock before calling cancel_work_sync() and
dropping the hash_entry reference. Repeat until no more entries require
purging. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: ti-qspi: fix use-after-free after DMA setup failure
The driver falls back to PIO mode if DMA setup fails during probe.
Make sure to clear the DMA channel pointer also if buffer allocation
fails to avoid passing a pointer to the released channel to the DMA
engine (or trying to free the channel a second time on late probe errors
or driver unbind).
This issue was flagged by Sashiko when reviewing a devres allocation
conversion patch. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: mcast: fix use-after-free in orig_node RCU release
batadv_mcast_purge_orig() removes entries from RCU-protected hlists but
does not wait for an RCU grace period before returning. Concurrent RCU
readers may still accesses references to those entries at the point of
removal. RCU-protected readers trying to operate on entries like
orig->mcast_want_all_ipv6_node will then access already freed memory.
Fix this by moving batadv_mcast_purge_orig() to batadv_orig_node_release(),
just before the call_rcu() invocation. This ensures RCU readers that were
active at purge time have drained before the orig_node memory is reclaimed. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/v3d: Fix use-after-free of CPU job query arrays on error path
The CPU job ioctl's fail label calls kvfree() on cpu_job's timestamp and
performance query arrays after v3d_job_cleanup(), which drops the job's
last reference and frees cpu_job. Reading cpu_job at that point is a
use-after-free. Also, on the early v3d_job_init() failure path, it is a
NULL dereference, since v3d_job_deallocate() zeroes the local pointer.
In the success path, the arrays are released from the scheduler's
.free_job callback, but on the error path, they are freed manually, as
the job was never pushed to the scheduler. While the success path deals
with this correctly, the fail path doesn't.
On top of that, the manual kvfree() calls only free the array storage;
they don't drm_syncobj_put() the per-query syncobjs that
v3d_timestamp_query_info_free() and v3d_performance_query_info_free()
release on the success path. So the same fail path that triggers the
use-after-free also leaks one syncobj reference per query.
Unify the CPU job teardown into the CPU job's kref destructor, mirroring
v3d_render_job_free(). The scheduler's .free_job slot reverts to the
generic v3d_sched_job_free() and the fail label drops the manual
kvfree() calls, leaving a single teardown path that is reached from both
the scheduler and the ioctl error path. That removes the use-after-free,
the NULL dereference, and the syncobj leak by construction. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: virt_concat: fix use-after-free in mtd_virt_concat_destroy_joins()
mtd_concat_destroy() frees item->concat so calling
mtd_virt_concat_put_mtd_devices(item->concat) leads to a use after free.
Fix this by moving mtd_virt_concat_put_mtd_devices() before
mtd_concat_destroy() |
| Use after free in Payments in Google Chrome prior to 151.0.7922.109 allowed a remote attacker to potentially perform a sandbox escape via a crafted HTML page. (Chromium security severity: High) |
| Use after free in Media in Google Chrome on Windows prior to 151.0.7922.109 allowed a remote attacker to potentially perform a sandbox escape via a crafted HTML page. (Chromium security severity: High) |
| Use after free in Web Authentication in Google Chrome prior to 151.0.7922.109 allowed a remote attacker to potentially perform a sandbox escape via a crafted HTML page. (Chromium security severity: High) |
