| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Use sender devcom for MPV master-up
After PCIe DPC recovery, mlx5 reloads the affected functions and
replays multiport affiliation events. In the reported failure, the
first relevant device error was:
pcieport 0000:10:01.1: DPC: containment event
pcieport 0000:10:01.1: PCIe Bus Error: severity=Uncorrected (Fatal)
pcieport 0000:10:01.1: [ 5] SDES (First)
mlx5 recovered the PCI functions and resumed 0000:11:00.1. During
that resume, RDMA multiport binding replayed
MLX5_DRIVER_EVENT_AFFILIATION_DONE and mlx5e sent
MPV_DEVCOM_MASTER_UP. The host then panicked with:
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: mlx5_devcom_comp_set_ready+0x5/0x40 [mlx5_core]
RDI: 0000000000000000
Call trace included:
mlx5_devcom_comp_set_ready
mlx5e_devcom_event_mpv
mlx5_devcom_send_event
mlx5_ib_bind_slave_port
mlx5r_mp_probe
mlx5_pci_resume
MPV devcom registration publishes mlx5e private data to the component
peer list before mlx5e_devcom_init_mpv() stores the returned component
device in priv->devcom. A concurrent master-up event can therefore
reach a peer whose private data is visible but whose priv->devcom
backpointer is still NULL.
MPV_DEVCOM_MASTER_UP already carries the sender/master mlx5e private
data as event_data. The ready bit is stored on the shared devcom
component, not on an individual peer. Use the sender devcom when
marking the MPV component ready.
This preserves the readiness transition while avoiding a NULL
dereference of the peer devcom pointer during affiliation replay after
PCI error recovery. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: fix peer refcount leak in TCP error paths
When either the TCP RX or TX error path calls ovpn_peer_hold() followed
by schedule_work(&peer->tcp.defer_del_work), and the work item is already
pending from the other path, schedule_work() returns false and the work
runs only once. Since ovpn_tcp_peer_del_work() calls ovpn_peer_put()
exactly once, the extra reference taken by the losing path is never
dropped, leaking the peer object.
The race window:
CPU0 (strparser/RX error): CPU1 (tcp_tx_work/TX error):
ovpn_peer_hold() <- refcnt+1 ovpn_peer_hold() <- refcnt+2
schedule_work() <- queued schedule_work() <- NO-OP
(work already pending)
ovpn_tcp_peer_del_work runs:
ovpn_peer_del()
ovpn_peer_put() <- refcnt+1
<- peer never freed
Fix by checking the return value of schedule_work() in both paths and
calling ovpn_peer_put() to drop the extra reference if the work was
already pending. ovpn_peer_hold() is kept unconditional in the TX path
as it cannot fail at that point. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gpusvm: Fix MM reference leak in drm_gpusvm_range_evict
If kvmalloc_array() fails in drm_gpusvm_range_evict(), the MM
reference acquired earlier is not released, resulting in a reference
leak.
Fix this by dropping the MM reference on the kvmalloc_array()
failure path. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/ttm: Account for NULL and handle pages in ttm_pool_backup
Pages in ttm_pool_backup can be NULL or backup handles
(ttm_backup_page_ptr_is_handle()), neither of which can be passed to
set_pages_array_wb() or freed. Add a dedicated WB pass before the
dma/purge loop that walks allocations using the same i += num_pages
stride, skipping NULL and handle entries, and calls set_pages_array_wb()
once per contiguous run of real pages. Apply the same NULL/handle guard
to the dma/purge loop.
Fixes the following oops:
Oops: general protection fault, kernel NULL pointer dereference 0x0: 0000 [#1] SMP NOPTI
RIP: 0010:__cpa_process_fault+0xf8/0x770
RSP: 0018:ffffc90000a87718 EFLAGS: 00010287
RAX: 0000000000000000 RBX: ffffc90000a87868 RCX: 0000000000000000
RDX: 0000000000001000 RSI: 0005088000000000 RDI: ffffffff827c5f34
RBP: 0005088000000000 R08: ffffc90000a877cb R09: ffffc90000a877d0
R10: 0000000000000000 R11: 000000000000001b R12: 000ffffffffff000
R13: ffffc90000a87868 R14: ffffc90000a87868 R15: ffff88815b882ae0
FS: 0000000000000000(0000) GS:ffff8884ec840000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f930b844000 CR3: 000000000262e003 CR4: 0000000008f70ef0
PKRU: 55555554
Call Trace:
<TASK>
__change_page_attr_set_clr+0x989/0xe90
? __purge_vmap_area_lazy+0x6c/0x3a0
? _vm_unmap_aliases+0x250/0x2a0
set_pages_array_wb+0x7f/0x120
ttm_pool_backup+0x4c9/0x5b0 [ttm]
? dma_resv_wait_timeout+0x3b/0xf0
ttm_tt_backup+0x32/0x60 [ttm]
ttm_bo_shrink+0x66/0x110 [ttm]
xe_bo_shrink_purge+0x12b/0x1b0 [xe]
xe_bo_shrink+0xbb/0x270 [xe]
__xe_shrinker_walk+0xf7/0x160 [xe]
xe_shrinker_walk+0x9d/0xc0 [xe]
xe_shrinker_scan+0x11f/0x210 [xe]
do_shrink_slab+0x13b/0x270
shrink_slab+0xf1/0x400
shrink_node+0x352/0x8a0
balance_pgdat+0x32c/0x700
kswapd+0x205/0x2f0
? __pfx_autoremove_wake_function+0x10/0x10
? __pfx_kswapd+0x10/0x10
kthread+0xd1/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x1b1/0x200
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix PTP Call Trace during PTP release
If a PF reset occurs when the PTP state is ICE_PTP_UNINIT, then
ice_ptp_rebuild() will update the state to ICE_PTP_ERROR. This will
result in the following PTP release call trace during driver unload:
kernel BUG at lib/list_debug.c:52!
ice_ptp_release+0x332/0x3c0 [ice]
ice_deinit_features.part.0+0x10e/0x120 [ice]
ice_remove+0x100/0x220 [ice]
This was observed when passing PF1 through to a VM. ice_ptp_init()
fails because ctrl_pf is NULL and sets the state to ICE_PTP_UNINIT.
Fix by detecting the ICE_PTP_UNINIT state in ice_ptp_rebuild() and
returning without error, preventing the invalid state transition to
ICE_PTP_ERROR. The only valid path to ICE_PTP_ERROR is from
ICE_PTP_RESETTING after a failed rebuild. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do not try compression for data reloc inodes
[BUG]
There is a syzbot report that the check inside get_new_location()
triggered:
BTRFS info (device loop0): found 31 extents, stage: move data extents
BTRFS info (device loop0): leaf 8908800 gen 16 total ptrs 28 free space 1676 owner 18446744073709551607
item 0 key (256 INODE_ITEM 0) itemoff 3835 itemsize 160
inode generation 5 transid 0 size 0 nbytes 0
block group 0 mode 40755 links 1 uid 0 gid 0
rdev 0 sequence 0 flags 0x0
atime 1669132761.0
ctime 1669132761.0
mtime 1669132761.0
otime 0.0
item 1 key (256 INODE_REF 256) itemoff 3823 itemsize 12
index 0 name_len 2
item 2 key (258 INODE_ITEM 0) itemoff 3663 itemsize 160
inode generation 1 transid 16 size 733184 nbytes 106496
block group 0 mode 100600 links 0 uid 0 gid 0
rdev 0 sequence 24 flags 0x18
item 3 key (258 EXTENT_DATA 0) itemoff 3595 itemsize 68
generation 16 type 0
inline extent data size 47 ram_bytes 4096 compression 1
[...]
item 27 key (18446744073709551611 ORPHAN_ITEM 258) itemoff 2376 itemsize 0
BTRFS error (device loop0): unexpected non-zero offset in file extent item for data reloc inode 258 key offset 0 offset 9277520992061368337
------------[ cut here ]------------
btrfs_abort_should_print_stack(__error)
[CAUSE]
The above dump tree shows the first file extent item is inlined, which
should make no sense for data reloc inodes, as such inodes just
represent where the data extents are in the relocation destination chunk.
However the relocation path preallocates space for each block,
then dirties them, cluster by cluster.
It's possible to have a single block at the beginning of the block
group, and no other block in the same cluster.
So relocation will preallocate a file extent for that block and dirty
the first block. Then memory pressure forces the data reloc inode to be
written back, before any other blocks are dirtied/allocated.
Finally commit 3eaf5f082c4c ("btrfs: extract inlined creation into a dedicated
delalloc helper") changed the sequence of delalloc. Before that commit we
always tried NOCOW first, so that dirtied block would be written back into
the preallocated space, and appear as a regular extent.
But with that commit, we always try inline first, and since compression
is forced, we try compressing the first block, and then inline the
compressed data, resulting in the above inlined file extent in the data
reloc tree.
Then the check in get_new_location() will check the file offset, without
checking if the file extent is inlined or not, resulting in the above
failure.
[FIX]
Do not allow compression for data reloc inodes.
Since data reloc inode sizes are always block aligned, as long as we do
not compress, @data_len will always be at least one block, and
that will cause can_cow_file_range_inline() to return false, thus no
inlined extent will be created. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: drop TXRX_NOTIFY on non-mmio buses
PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7925_rx_check() and
mt7925_queue_rx_skb() dispatch it to mt7925_mac_tx_free() on every bus.
mt7925_mac_tx_free() cleans the DMA tx queues with
mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the
mmio queue ops implement that callback; on USB it is NULL, so a
TXRX_NOTIFY there calls a NULL pointer in the RX worker:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:0x0
Call Trace:
mt7925_mac_tx_free+0x58/0x350 [mt7925_common]
mt7925_rx_check+0xe2/0x130 [mt7925_common]
mt76u_rx_worker+0x1b9/0x620 [mt76_usb]
Drop the event on non-mmio buses via mt76_is_mmio(), as in
commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for
non-mmio devices"). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: dce100: skip non-DP stream encoders for DP MST
On DCE8-class ASICs (e.g. Bonaire), the resource pool contains digital
DIG stream encoders plus one analog DAC encoder. When assigning a stream
encoder for a second DisplayPort MST stream, if the preferred digital
encoder is already acquired, dce100_find_first_free_match_stream_enc_for_link()
falls back to the first free pool entry. That entry may be the analog
encoder, whose funcs table lacks DP hooks such as dp_set_stream_attribute.
The subsequent atomic commit then dereferences NULL function pointers in
link_set_dpms_on() and crashes.
Skip encoders without dp_set_stream_attribute when the stream uses a DP
signal (including MST). Use dc_is_dp_signal(stream->signal) for the MST
fallback path instead of checking only the link connector signal.
Tested on:
- GPU: AMD Radeon R7 260X (Bonaire / DCE8)
- Board: Supermicro C9X299-PG300
- Setup: DP MST daisy chain, hotplug second monitor or have it connected on boot
- Kernel: 7.1.3 (issue observed since 6.19)
- Result: kernel oops without patch; dual monitors stable with patch
(cherry picked from commit 28ec64943e3ee4d9b8d30cea61e380f1429953a8) |
| In the Linux kernel, the following vulnerability has been resolved:
media: mali-c55: Fix possible ERR_PTR in enable_streams
The media_pad_remote_pad_unique() function returns either a valid
pointer or an ERR_PTR() on failure (-ENOTUNIQ if multiple links are
enabled, -ENOLINK if no connected pad is found). The return value
was assigned directly to isp->remote_src and dereferenced in the
next line without checking for errors, which could lead to an
ERR_PTR dereference.
Add proper error checking with IS_ERR() before dereferencing the
pointer. Also set isp->remote_src to NULL on error to maintain
consistency with other error paths in the function. |
| In the Linux kernel, the following vulnerability has been resolved:
media: i2c: alvium: fix critical pointer access in alvium_ctrl_init
The current implementation of alvium_ctrl_init creates several controls in
function alvium_ctrl_init and uses the returned pointer without check. That
can cause write access over NULL-pointer for several controls. The reworked
code checks the pointers before adding flags. |
| In the Linux kernel, the following vulnerability has been resolved:
media: ti: vpe: Fix the error code of devm_kzalloc() in vip_probe_slice()
In vip_probe_slice(), the error check for devm_kzalloc() incorrectly
uses PTR_ERR_OR_ZERO() which returns 0 for NULL pointer.
Return -ENOMEM for devm_kzalloc() failure. |
| A flaw was found in the Linux kernel's udmabuf device driver, within a fault handler. This issue occurs due to the lack of proper validation of user-supplied data, which can result in memory access past the end of an array. This may allow an attacker to escalate privileges and execute arbitrary code in the context of the kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Preserve rq tracking across local DSQ dispatch
dispatch_to_local_dsq() can run from scx_bpf_dsq_move_to_local() while
ops.dispatch() has recorded the current rq. Moving a task to a local DSQ
may switch to the source or destination rq before synchronously invoking
ops.dequeue() through the following path:
SCX_CALL_OP(dispatch, rq)
ops.dispatch()
scx_bpf_dsq_move_to_local()
scx_flush_dispatch_buf()
finish_dispatch()
dispatch_to_local_dsq()
scx_dispatch_enqueue()
local_dsq_post_enq()
call_task_dequeue()
SCX_CALL_OP_TASK(dequeue, locked_rq, ...)
The nested callback saves the recorded rq and restores it on return. If
the rq tracking does not follow the lock switch, update_locked_rq() can
trigger the following lockdep assertion while restoring an rq which is
no longer held:
WARNING: kernel/sched/sched.h:1641 at call_task_dequeue+0x160/0x170
Call Trace:
scx_dispatch_enqueue+0x2b0/0x460
dispatch_to_local_dsq+0x138/0x230
scx_flush_dispatch_buf+0x1af/0x220
scx_bpf_dsq_move_to_local___v2+0xe2/0x1c0
bpf__sched_ext_ops_dispatch+0x4b/0xa7
do_pick_task_scx+0x3b6/0x910
__pick_next_task+0x105/0x1f0
__schedule+0x3e7/0x1980
Introduce switch_rq_lock() to update the tracking state together with
each rq lock handoff. Use it in dispatch_to_local_dsq(),
move_remote_task_to_local_dsq() and the in-balance paths of
scx_dsq_move(), ensuring that scx_locked_rq() consistently refers to the
rq whose lock is actually held throughout the lock dance. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: fix race between registration and connection abortion
This fixes this race:
- thread a: io_uring_enter -> register sqe ->
fuse_uring_create_ring_ent -> allocate ent but doesn't grab queue_ref
yet
- thread b: fuse_conn_destroy() -> fuse_chan_abort() ->
fuse_uring_abort() is a no-op due to queue ref being 0
- thread a: grabs the queue_ref, queue_ref is now 1, rest of
fuse_uring_do_register() logic executes
- thread b: fuse_chan_abort() returns, fuse_chan_wait_aborted() now runs
and calls
"wait_event(ring->stop_waitq, atomic_read(&ring->queue_refs) == 0);"
The abort/unmount thread will hang indefinitely in unkillable state as
nothing will decrement queue_refs or wake stop_waitq, and the ring,
queue, and ent are leaked.
Fix this by checking fch->connected under fch->lock after the created
ent has grabbed a ref count on the queue. This ensures that in the
scenario above, it is guaranteed that we either release the queue ref
and wake up stop_waitq (in case fuse_chan_wait_aborted() is already
waiting) in fuse_uring_do_register() when we detect !fch->connected, or
if the connection is aborted after the check, it is guaranteed that the
async teardown worker will be running in the background cleaning up ents
and decrementing the ent's ref on the queue, which will unblock the
eventual queue and ring teardown. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix aperture mapping leak
amdgpu_pci_remove() calls drm_dev_unplug() before invoking the driver
fini routines. This causes drm_dev_enter() in amdgpu_ttm_fini() to
always return false, so iounmap(aper_base_kaddr) never runs on normal
driver unload, leaving an orphaned entry in the x86 PAT interval tree.
On connected_to_cpu hardware, the aperture is mapped write-back (WB) via
ioremap_cache(). On reload, IP discovery calls memremap(..., MEMREMAP_WC)
over the same range. The WC vs WB conflict causes:
ioremap error for 0x..., requested 0x1, got 0x0
amdgpu: discovery failed: -2
Fix by switching to devres-managed mappings so cleanup is guaranteed
regardless of drm_dev_enter() state:
- connected_to_cpu path: devm_memremap(MEMREMAP_WB). For
IORESOURCE_SYSTEM_RAM ranges this takes the try_ram_remap() shortcut,
returning __va(offset) from the existing kernel direct map. No new
ioremap VA or PAT entry is created, so there is nothing to orphan.
- dGPU path: devm_ioremap_wc() registers iounmap() as a devres action,
guaranteeing cleanup at device_del() time.
Also remove iounmap(aper_base_kaddr) from amdgpu_device_unmap_mmio()
since the mapping is now devres-owned.
v2: Remove redundant x86_64 guard (Lijo)
(cherry picked from commit d871e99879cb5fd1fa798b006b4888887e63a17a) |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix irq-disabled in local_bh_enable()
The rxrpc_assess_MTU_size() function calls down into the IP layer to find
out the MTU size for a route. When accepting an incoming call, this is
called from rxrpc_new_incoming_call() which holds interrupts disabled
across the code that calls down to it. Unfortunately, the IP layer uses
local_bh_enable() which, config dependent, throws a warning if IRQs are
enabled:
WARNING: CPU: 1 PID: 5544 at kernel/softirq.c:387 __local_bh_enable_ip+0x43/0xd0
...
RIP: 0010:__local_bh_enable_ip+0x43/0xd0
...
Call Trace:
<TASK>
rt_cache_route+0x7e/0xa0
rt_set_nexthop.isra.0+0x3b3/0x3f0
__mkroute_output+0x43a/0x460
ip_route_output_key_hash+0xf7/0x140
ip_route_output_flow+0x1b/0x90
rxrpc_assess_MTU_size.isra.0+0x2a0/0x590
rxrpc_new_incoming_peer+0x46/0x120
rxrpc_alloc_incoming_call+0x1b1/0x400
rxrpc_new_incoming_call+0x1da/0x5e0
rxrpc_input_packet+0x827/0x900
rxrpc_io_thread+0x403/0xb60
kthread+0x2f7/0x310
ret_from_fork+0x2a/0x230
ret_from_fork_asm+0x1a/0x30
...
hardirqs last enabled at (23): _raw_spin_unlock_irq+0x24/0x50
hardirqs last disabled at (24): _raw_read_lock_irq+0x17/0x70
softirqs last enabled at (0): copy_process+0xc61/0x2730
softirqs last disabled at (25): rt_add_uncached_list+0x3c/0x90
Fix this by moving the call to rxrpc_assess_MTU_size() out of
rxrpc_init_peer() and further up the stack where it can be done without
interrupts disabled.
It shouldn't be a problem for rxrpc_new_incoming_call() to do it after the
locks are dropped as pmtud is going to be performed by the I/O thread - and
we're in the I/O thread at this point. |
| Nefteprodukttekhnika BUK TS-G Gas Station Automation System 2.9.1 on Linux contains a SQL Injection vulnerability (CWE-89) in the system configuration module. A remote attacker can send specially crafted HTTP POST requests to the /php/request.php endpoint via the sql parameter in application/x-www-form-urlencoded data (e.g., action=do&sql=<query_here>&reload_driver=0) to execute arbitrary SQL commands and potentially achieve remote code execution. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: fix data races on ring->ready
On weakly-ordered architectures, the store to fiq->ops can be
reordered past the store to ring->ready, allowing a CPU that sees
ring->ready == true via fuse_uring_ready() to dispatch requests
through a stale fiq->ops pointer. Upgrade the store to
smp_store_release() and the load in fuse_uring_ready() to
smp_load_acquire() so that the preceding WRITE_ONCE(fiq->ops, ...)
is visible to any CPU that observes ring->ready == true.
Additionally, fuse_uring_do_register() publishes ring->ready with
WRITE_ONCE() but the fast-path check reads it with a plain load.
This is a marked-vs-unmarked access that KCSAN will flag. Wrap it in
READ_ONCE() to mark it without adding unnecessary ordering.
Also wrap the fc->ring load in fuse_uring_ready() in READ_ONCE() to
prevent the compiler from reloading it between the NULL check and the
dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: arc: emac: quiesce interrupts before requesting IRQ
Normal RX/TX interrupts are enabled later, in arc_emac_open(), so probe
should not see interrupt delivery in the usual case. However, hardware may
still present stale or latched interrupt status left by firmware or the
bootloader.
If probe later unwinds after devm_request_irq() has installed the handler,
such a stale interrupt can still reach arc_emac_intr() during teardown and
race with release of the associated net_device.
Avoid that window by putting the device into a known quiescent state before
requesting the IRQ: disable all EMAC interrupt sources and clear any
pending EMAC interrupt status bits. This keeps the change hardware-focused
and minimal, while preventing spurious IRQ delivery from leftover state. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix unsol_bcast_probe_resp double free on alloc failure
ieee80211_set_unsol_bcast_probe_resp() calls kfree_rcu() on the old
template before allocating the replacement. If the kzalloc() then fails,
it returns -ENOMEM while link->u.ap.unsol_bcast_probe_resp still points
at the object already queued for freeing. A later update or AP teardown
re-queues that same rcu_head; the second free is caught by KASAN when the
RCU sheaf is processed in softirq:
BUG: KASAN: double-free in rcu_free_sheaf (mm/slub.c:5850)
Free of addr ffff88800d06f300 by task exploit/145
...
__rcu_free_sheaf_prepare (mm/slub.c:2634 mm/slub.c:2940)
rcu_free_sheaf (mm/slub.c:5850)
rcu_core (kernel/rcu/tree.c:2617 kernel/rcu/tree.c:2869)
handle_softirqs (kernel/softirq.c:622)
The buggy address belongs to the cache kmalloc-128 of size 128
Queue the old object for kfree_rcu() only after the new one is published,
matching ieee80211_set_probe_resp() and ieee80211_set_s1g_short_beacon(). |
