| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: Revert "scsi: qla2xxx: Perform lockless command completion in abort path"
This reverts commit 0367076b0817d5c75dfb83001ce7ce5c64d803a9.
The commit being reverted added code to __qla2x00_abort_all_cmds() to
call sp->done() without holding a spinlock. But unlike the older code
below it, this new code failed to check sp->cmd_type and just assumed
TYPE_SRB, which results in a jump to an invalid pointer in target-mode
with TYPE_TGT_CMD:
qla2xxx [0000:65:00.0]-d034:8: qla24xx_do_nack_work create sess success
0000000009f7a79b
qla2xxx [0000:65:00.0]-5003:8: ISP System Error - mbx1=1ff5h mbx2=10h
mbx3=0h mbx4=0h mbx5=191h mbx6=0h mbx7=0h.
qla2xxx [0000:65:00.0]-d01e:8: -> fwdump no buffer
qla2xxx [0000:65:00.0]-f03a:8: qla_target(0): System error async event
0x8002 occurred
qla2xxx [0000:65:00.0]-00af:8: Performing ISP error recovery -
ha=0000000058183fda.
BUG: kernel NULL pointer dereference, address: 0000000000000000
PF: supervisor instruction fetch in kernel mode
PF: error_code(0x0010) - not-present page
PGD 0 P4D 0
Oops: 0010 [#1] SMP
CPU: 2 PID: 9446 Comm: qla2xxx_8_dpc Tainted: G O 6.1.133 #1
Hardware name: Supermicro Super Server/X11SPL-F, BIOS 4.2 12/15/2023
RIP: 0010:0x0
Code: Unable to access opcode bytes at 0xffffffffffffffd6.
RSP: 0018:ffffc90001f93dc8 EFLAGS: 00010206
RAX: 0000000000000282 RBX: 0000000000000355 RCX: ffff88810d16a000
RDX: ffff88810dbadaa8 RSI: 0000000000080000 RDI: ffff888169dc38c0
RBP: ffff888169dc38c0 R08: 0000000000000001 R09: 0000000000000045
R10: ffffffffa034bdf0 R11: 0000000000000000 R12: ffff88810800bb40
R13: 0000000000001aa8 R14: ffff888100136610 R15: ffff8881070f7400
FS: 0000000000000000(0000) GS:ffff88bf80080000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 000000010c8ff006 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? __die+0x4d/0x8b
? page_fault_oops+0x91/0x180
? trace_buffer_unlock_commit_regs+0x38/0x1a0
? exc_page_fault+0x391/0x5e0
? asm_exc_page_fault+0x22/0x30
__qla2x00_abort_all_cmds+0xcb/0x3e0 [qla2xxx_scst]
qla2x00_abort_all_cmds+0x50/0x70 [qla2xxx_scst]
qla2x00_abort_isp_cleanup+0x3b7/0x4b0 [qla2xxx_scst]
qla2x00_abort_isp+0xfd/0x860 [qla2xxx_scst]
qla2x00_do_dpc+0x581/0xa40 [qla2xxx_scst]
kthread+0xa8/0xd0
</TASK>
Then commit 4475afa2646d ("scsi: qla2xxx: Complete command early within
lock") added the spinlock back, because not having the lock caused a
race and a crash. But qla2x00_abort_srb() in the switch below already
checks for qla2x00_chip_is_down() and handles it the same way, so the
code above the switch is now redundant and still buggy in target-mode.
Remove it. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: ets: Remove drr class from the active list if it changes to strict
Whenever a user issues an ets qdisc change command, transforming a
drr class into a strict one, the ets code isn't checking whether that
class was in the active list and removing it. This means that, if a
user changes a strict class (which was in the active list) back to a drr
one, that class will be added twice to the active list [1].
Doing so with the following commands:
tc qdisc add dev lo root handle 1: ets bands 2 strict 1
tc qdisc add dev lo parent 1:2 handle 20: \
tbf rate 8bit burst 100b latency 1s
tc filter add dev lo parent 1: basic classid 1:2
ping -c1 -W0.01 -s 56 127.0.0.1
tc qdisc change dev lo root handle 1: ets bands 2 strict 2
tc qdisc change dev lo root handle 1: ets bands 2 strict 1
ping -c1 -W0.01 -s 56 127.0.0.1
Will trigger the following splat with list debug turned on:
[ 59.279014][ T365] ------------[ cut here ]------------
[ 59.279452][ T365] list_add double add: new=ffff88801d60e350, prev=ffff88801d60e350, next=ffff88801d60e2c0.
[ 59.280153][ T365] WARNING: CPU: 3 PID: 365 at lib/list_debug.c:35 __list_add_valid_or_report+0x17f/0x220
[ 59.280860][ T365] Modules linked in:
[ 59.281165][ T365] CPU: 3 UID: 0 PID: 365 Comm: tc Not tainted 6.18.0-rc7-00105-g7e9f13163c13-dirty #239 PREEMPT(voluntary)
[ 59.281977][ T365] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 59.282391][ T365] RIP: 0010:__list_add_valid_or_report+0x17f/0x220
[ 59.282842][ T365] Code: 89 c6 e8 d4 b7 0d ff 90 0f 0b 90 90 31 c0 e9 31 ff ff ff 90 48 c7 c7 e0 a0 22 9f 48 89 f2 48 89 c1 4c 89 c6 e8 b2 b7 0d ff 90 <0f> 0b 90 90 31 c0 e9 0f ff ff ff 48 89 f7 48 89 44 24 10 4c 89 44
...
[ 59.288812][ T365] Call Trace:
[ 59.289056][ T365] <TASK>
[ 59.289224][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.289546][ T365] ets_qdisc_change+0xd2b/0x1e80
[ 59.289891][ T365] ? __lock_acquire+0x7e7/0x1be0
[ 59.290223][ T365] ? __pfx_ets_qdisc_change+0x10/0x10
[ 59.290546][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.290898][ T365] ? __mutex_trylock_common+0xda/0x240
[ 59.291228][ T365] ? __pfx___mutex_trylock_common+0x10/0x10
[ 59.291655][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.291993][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.292313][ T365] ? trace_contention_end+0xc8/0x110
[ 59.292656][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.293022][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.293351][ T365] tc_modify_qdisc+0x63a/0x1cf0
Fix this by always checking and removing an ets class from the active list
when changing it to strict.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/tree/net/sched/sch_ets.c?id=ce052b9402e461a9aded599f5b47e76bc727f7de#n663 |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: NFSv4 file creation neglects setting ACL
An NFSv4 client that sets an ACL with a named principal during file
creation retrieves the ACL afterwards, and finds that it is only a
default ACL (based on the mode bits) and not the ACL that was
requested during file creation. This violates RFC 8881 section
6.4.1.3: "the ACL attribute is set as given".
The issue occurs in nfsd_create_setattr(), which calls
nfsd_attrs_valid() to determine whether to call nfsd_setattr().
However, nfsd_attrs_valid() checks only for iattr changes and
security labels, but not POSIX ACLs. When only an ACL is present,
the function returns false, nfsd_setattr() is skipped, and the
POSIX ACL is never applied to the inode.
Subsequently, when the client retrieves the ACL, the server finds
no POSIX ACL on the inode and returns one generated from the file's
mode bits rather than returning the originally-specified ACL. |
| In the Linux kernel, the following vulnerability has been resolved:
mlxsw: spectrum_router: Fix neighbour use-after-free
We sometimes observe use-after-free when dereferencing a neighbour [1].
The problem seems to be that the driver stores a pointer to the
neighbour, but without holding a reference on it. A reference is only
taken when the neighbour is used by a nexthop.
Fix by simplifying the reference counting scheme. Always take a
reference when storing a neighbour pointer in a neighbour entry. Avoid
taking a referencing when the neighbour is used by a nexthop as the
neighbour entry associated with the nexthop already holds a reference.
Tested by running the test that uncovered the problem over 300 times.
Without this patch the problem was reproduced after a handful of
iterations.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_neigh_entry_update+0x2d4/0x310
Read of size 8 at addr ffff88817f8e3420 by task ip/3929
CPU: 3 UID: 0 PID: 3929 Comm: ip Not tainted 6.18.0-rc4-virtme-g36b21a067510 #3 PREEMPT(full)
Hardware name: Nvidia SN5600/VMOD0013, BIOS 5.13 05/31/2023
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xa0
print_address_description.constprop.0+0x6e/0x300
print_report+0xfc/0x1fb
kasan_report+0xe4/0x110
mlxsw_sp_neigh_entry_update+0x2d4/0x310
mlxsw_sp_router_rif_gone_sync+0x35f/0x510
mlxsw_sp_rif_destroy+0x1ea/0x730
mlxsw_sp_inetaddr_port_vlan_event+0xa1/0x1b0
__mlxsw_sp_inetaddr_lag_event+0xcc/0x130
__mlxsw_sp_inetaddr_event+0xf5/0x3c0
mlxsw_sp_router_netdevice_event+0x1015/0x1580
notifier_call_chain+0xcc/0x150
call_netdevice_notifiers_info+0x7e/0x100
__netdev_upper_dev_unlink+0x10b/0x210
netdev_upper_dev_unlink+0x79/0xa0
vrf_del_slave+0x18/0x50
do_set_master+0x146/0x7d0
do_setlink.isra.0+0x9a0/0x2880
rtnl_newlink+0x637/0xb20
rtnetlink_rcv_msg+0x6fe/0xb90
netlink_rcv_skb+0x123/0x380
netlink_unicast+0x4a3/0x770
netlink_sendmsg+0x75b/0xc90
__sock_sendmsg+0xbe/0x160
____sys_sendmsg+0x5b2/0x7d0
___sys_sendmsg+0xfd/0x180
__sys_sendmsg+0x124/0x1c0
do_syscall_64+0xbb/0xfd0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
[...]
Allocated by task 109:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7b/0x90
__kmalloc_noprof+0x2c1/0x790
neigh_alloc+0x6af/0x8f0
___neigh_create+0x63/0xe90
mlxsw_sp_nexthop_neigh_init+0x430/0x7e0
mlxsw_sp_nexthop_type_init+0x212/0x960
mlxsw_sp_nexthop6_group_info_init.constprop.0+0x81f/0x1280
mlxsw_sp_nexthop6_group_get+0x392/0x6a0
mlxsw_sp_fib6_entry_create+0x46a/0xfd0
mlxsw_sp_router_fib6_replace+0x1ed/0x5f0
mlxsw_sp_router_fib6_event_work+0x10a/0x2a0
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Freed by task 154:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x43/0x70
kmem_cache_free_bulk.part.0+0x1eb/0x5e0
kvfree_rcu_bulk+0x1f2/0x260
kfree_rcu_work+0x130/0x1b0
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Last potentially related work creation:
kasan_save_stack+0x30/0x50
kasan_record_aux_stack+0x8c/0xa0
kvfree_call_rcu+0x93/0x5b0
mlxsw_sp_router_neigh_event_work+0x67d/0x860
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
mlxsw: spectrum_mr: Fix use-after-free when updating multicast route stats
Cited commit added a dedicated mutex (instead of RTNL) to protect the
multicast route list, so that it will not change while the driver
periodically traverses it in order to update the kernel about multicast
route stats that were queried from the device.
One instance of list entry deletion (during route replace) was missed
and it can result in a use-after-free [1].
Fix by acquiring the mutex before deleting the entry from the list and
releasing it afterwards.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum]
Read of size 8 at addr ffff8881523c2fa8 by task kworker/2:5/22043
CPU: 2 UID: 0 PID: 22043 Comm: kworker/2:5 Not tainted 6.18.0-rc1-custom-g1a3d6d7cd014 #1 PREEMPT(full)
Hardware name: Mellanox Technologies Ltd. MSN2010/SA002610, BIOS 5.6.5 08/24/2017
Workqueue: mlxsw_core mlxsw_sp_mr_stats_update [mlxsw_spectrum]
Call Trace:
<TASK>
dump_stack_lvl+0xba/0x110
print_report+0x174/0x4f5
kasan_report+0xdf/0x110
mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 29933:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
mlxsw_sp_mr_route_add+0xd8/0x4770 [mlxsw_spectrum]
mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
Freed by task 29933:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3b/0x70
__kasan_slab_free+0x43/0x70
kfree+0x14e/0x700
mlxsw_sp_mr_route_add+0x2dea/0x4770 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:444 [mlxsw_spectrum]
mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
ethtool: Avoid overflowing userspace buffer on stats query
The ethtool -S command operates across three ioctl calls:
ETHTOOL_GSSET_INFO for the size, ETHTOOL_GSTRINGS for the names, and
ETHTOOL_GSTATS for the values.
If the number of stats changes between these calls (e.g., due to device
reconfiguration), userspace's buffer allocation will be incorrect,
potentially leading to buffer overflow.
Drivers are generally expected to maintain stable stat counts, but some
drivers (e.g., mlx5, bnx2x, bna, ksz884x) use dynamic counters, making
this scenario possible.
Some drivers try to handle this internally:
- bnad_get_ethtool_stats() returns early in case stats.n_stats is not
equal to the driver's stats count.
- micrel/ksz884x also makes sure not to write anything beyond
stats.n_stats and overflow the buffer.
However, both use stats.n_stats which is already assigned with the value
returned from get_sset_count(), hence won't solve the issue described
here.
Change ethtool_get_strings(), ethtool_get_stats(),
ethtool_get_phy_stats() to not return anything in case of a mismatch
between userspace's size and get_sset_size(), to prevent buffer
overflow.
The returned n_stats value will be equal to zero, to reflect that
nothing has been returned.
This could result in one of two cases when using upstream ethtool,
depending on when the size change is detected:
1. When detected in ethtool_get_strings():
# ethtool -S eth2
no stats available
2. When detected in get stats, all stats will be reported as zero.
Both cases are presumably transient, and a subsequent ethtool call
should succeed.
Other than the overflow avoidance, these two cases are very evident (no
output/cleared stats), which is arguably better than presenting
incorrect/shifted stats.
I also considered returning an error instead of a "silent" response, but
that seems more destructive towards userspace apps.
Notes:
- This patch does not claim to fix the inherent race, it only makes sure
that we do not overflow the userspace buffer, and makes for a more
predictable behavior.
- RTNL lock is held during each ioctl, the race window exists between
the separate ioctl calls when the lock is released.
- Userspace ethtool always fills stats.n_stats, but it is likely that
these stats ioctls are implemented in other userspace applications
which might not fill it. The added code checks that it's not zero,
to prevent any regressions. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix a job->pasid access race in gpu recovery
Avoid a possible UAF in GPU recovery due to a race between
the sched timeout callback and the tdr work queue.
The gpu recovery function calls drm_sched_stop() and
later drm_sched_start(). drm_sched_start() restarts
the tdr queue which will eventually free the job. If
the tdr queue frees the job before time out callback
completes, the job will be freed and we'll get a UAF
when accessing the pasid. Cache it early to avoid the
UAF.
Example KASAN trace:
[ 493.058141] BUG: KASAN: slab-use-after-free in amdgpu_device_gpu_recover+0x968/0x990 [amdgpu]
[ 493.067530] Read of size 4 at addr ffff88b0ce3f794c by task kworker/u128:1/323
[ 493.074892]
[ 493.076485] CPU: 9 UID: 0 PID: 323 Comm: kworker/u128:1 Tainted: G E 6.16.0-1289896.2.zuul.bf4f11df81c1410bbe901c4373305a31 #1 PREEMPT(voluntary)
[ 493.076493] Tainted: [E]=UNSIGNED_MODULE
[ 493.076495] Hardware name: TYAN B8021G88V2HR-2T/S8021GM2NR-2T, BIOS V1.03.B10 04/01/2019
[ 493.076500] Workqueue: amdgpu-reset-dev drm_sched_job_timedout [gpu_sched]
[ 493.076512] Call Trace:
[ 493.076515] <TASK>
[ 493.076518] dump_stack_lvl+0x64/0x80
[ 493.076529] print_report+0xce/0x630
[ 493.076536] ? _raw_spin_lock_irqsave+0x86/0xd0
[ 493.076541] ? __pfx__raw_spin_lock_irqsave+0x10/0x10
[ 493.076545] ? amdgpu_device_gpu_recover+0x968/0x990 [amdgpu]
[ 493.077253] kasan_report+0xb8/0xf0
[ 493.077258] ? amdgpu_device_gpu_recover+0x968/0x990 [amdgpu]
[ 493.077965] amdgpu_device_gpu_recover+0x968/0x990 [amdgpu]
[ 493.078672] ? __pfx_amdgpu_device_gpu_recover+0x10/0x10 [amdgpu]
[ 493.079378] ? amdgpu_coredump+0x1fd/0x4c0 [amdgpu]
[ 493.080111] amdgpu_job_timedout+0x642/0x1400 [amdgpu]
[ 493.080903] ? pick_task_fair+0x24e/0x330
[ 493.080910] ? __pfx_amdgpu_job_timedout+0x10/0x10 [amdgpu]
[ 493.081702] ? _raw_spin_lock+0x75/0xc0
[ 493.081708] ? __pfx__raw_spin_lock+0x10/0x10
[ 493.081712] drm_sched_job_timedout+0x1b0/0x4b0 [gpu_sched]
[ 493.081721] ? __pfx__raw_spin_lock_irq+0x10/0x10
[ 493.081725] process_one_work+0x679/0xff0
[ 493.081732] worker_thread+0x6ce/0xfd0
[ 493.081736] ? __pfx_worker_thread+0x10/0x10
[ 493.081739] kthread+0x376/0x730
[ 493.081744] ? __pfx_kthread+0x10/0x10
[ 493.081748] ? __pfx__raw_spin_lock_irq+0x10/0x10
[ 493.081751] ? __pfx_kthread+0x10/0x10
[ 493.081755] ret_from_fork+0x247/0x330
[ 493.081761] ? __pfx_kthread+0x10/0x10
[ 493.081764] ret_from_fork_asm+0x1a/0x30
[ 493.081771] </TASK>
(cherry picked from commit 20880a3fd5dd7bca1a079534cf6596bda92e107d) |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: fix middle attribute validation in push_nsh() action
The push_nsh() action structure looks like this:
OVS_ACTION_ATTR_PUSH_NSH(OVS_KEY_ATTR_NSH(OVS_NSH_KEY_ATTR_BASE,...))
The outermost OVS_ACTION_ATTR_PUSH_NSH attribute is OK'ed by the
nla_for_each_nested() inside __ovs_nla_copy_actions(). The innermost
OVS_NSH_KEY_ATTR_BASE/MD1/MD2 are OK'ed by the nla_for_each_nested()
inside nsh_key_put_from_nlattr(). But nothing checks if the attribute
in the middle is OK. We don't even check that this attribute is the
OVS_KEY_ATTR_NSH. We just do a double unwrap with a pair of nla_data()
calls - first time directly while calling validate_push_nsh() and the
second time as part of the nla_for_each_nested() macro, which isn't
safe, potentially causing invalid memory access if the size of this
attribute is incorrect. The failure may not be noticed during
validation due to larger netlink buffer, but cause trouble later during
action execution where the buffer is allocated exactly to the size:
BUG: KASAN: slab-out-of-bounds in nsh_hdr_from_nlattr+0x1dd/0x6a0 [openvswitch]
Read of size 184 at addr ffff88816459a634 by task a.out/22624
CPU: 8 UID: 0 PID: 22624 6.18.0-rc7+ #115 PREEMPT(voluntary)
Call Trace:
<TASK>
dump_stack_lvl+0x51/0x70
print_address_description.constprop.0+0x2c/0x390
kasan_report+0xdd/0x110
kasan_check_range+0x35/0x1b0
__asan_memcpy+0x20/0x60
nsh_hdr_from_nlattr+0x1dd/0x6a0 [openvswitch]
push_nsh+0x82/0x120 [openvswitch]
do_execute_actions+0x1405/0x2840 [openvswitch]
ovs_execute_actions+0xd5/0x3b0 [openvswitch]
ovs_packet_cmd_execute+0x949/0xdb0 [openvswitch]
genl_family_rcv_msg_doit+0x1d6/0x2b0
genl_family_rcv_msg+0x336/0x580
genl_rcv_msg+0x9f/0x130
netlink_rcv_skb+0x11f/0x370
genl_rcv+0x24/0x40
netlink_unicast+0x73e/0xaa0
netlink_sendmsg+0x744/0xbf0
__sys_sendto+0x3d6/0x450
do_syscall_64+0x79/0x2c0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
</TASK>
Let's add some checks that the attribute is properly sized and it's
the only one attribute inside the action. Technically, there is no
real reason for OVS_KEY_ATTR_NSH to be there, as we know that we're
pushing an NSH header already, it just creates extra nesting, but
that's how uAPI works today. So, keeping as it is. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: Reset t_task_cdb pointer in error case
If allocation of cmd->t_task_cdb fails, it remains NULL but is later
dereferenced in the 'err' path.
In case of error, reset NULL t_task_cdb value to point at the default
fixed-size buffer.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Fix XDP_TX path
For XDP_TX action in bnxt_rx_xdp(), clearing of the event flags is not
correct. __bnxt_poll_work() -> bnxt_rx_pkt() -> bnxt_rx_xdp() may be
looping within NAPI and some event flags may be set in earlier
iterations. In particular, if BNXT_TX_EVENT is set earlier indicating
some XDP_TX packets are ready and pending, it will be cleared if it is
XDP_TX action again. Normally, we will set BNXT_TX_EVENT again when we
successfully call __bnxt_xmit_xdp(). But if the TX ring has no more
room, the flag will not be set. This will cause the TX producer to be
ahead but the driver will not hit the TX doorbell.
For multi-buf XDP_TX, there is no need to clear the event flags and set
BNXT_AGG_EVENT. The BNXT_AGG_EVENT flag should have been set earlier in
bnxt_rx_pkt().
The visible symptom of this is that the RX ring associated with the
TX XDP ring will eventually become empty and all packets will be dropped.
Because this condition will cause the driver to not refill the RX ring
seeing that the TX ring has forever pending XDP_TX packets.
The fix is to only clear BNXT_RX_EVENT when we have successfully
called __bnxt_xmit_xdp(). |
| In the Linux kernel, the following vulnerability has been resolved:
NFS: Automounted filesystems should inherit ro,noexec,nodev,sync flags
When a filesystem is being automounted, it needs to preserve the
user-set superblock mount options, such as the "ro" flag. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: firewire-motu: add bounds check in put_user loop for DSP events
In the DSP event handling code, a put_user() loop copies event data.
When the user buffer size is not aligned to 4 bytes, it could overwrite
beyond the buffer boundary.
Fix by adding a bounds check before put_user(). |
| A vulnerability was detected in D-Link E15, M32, R15 and R32. This issue affects some unknown processing of the file /etc/emDaemon/passwd of the component MQTT Broker. The manipulation results in hard-coded credentials. It is possible to launch the attack remotely. The exploit is now public and may be used. |
| A weakness has been identified in vraj404 Criminal Management System up to 2808d057e7ddc5295519a487365b0cacfd0ba8c4. Affected by this vulnerability is an unknown functionality of the file home.php of the component Submission Form. This manipulation of the argument id/name/offName/crime/dob/arrDate/crimeDate/sex/address/folder/more causes sql injection. The attack is possible to be carried out remotely. The exploit has been made available to the public and could be used for attacks. This product adopts a rolling release strategy to maintain continuous delivery. Therefore, version details for affected or updated releases cannot be specified. The project was informed of the problem early through an issue report but has not responded yet. |
| Memory corruption in DOM in Google Chrome prior to 155.0.8059.84 allowed a remote attacker to execute arbitrary code inside the sandbox via a crafted HTML page. (Chromium security severity: High) |
| Memory corruption in Workers in Google Chrome prior to 155.0.8059.84 allowed a remote attacker to potentially execute arbitrary code inside the sandbox via a crafted HTML page. (Chromium security severity: Medium) |
| Use after free in Compositing in Google Chrome prior to 155.0.8059.84 allowed a remote attacker to execute arbitrary code inside the sandbox via a crafted HTML page. (Chromium security severity: Medium) |
| Television (tv) 0.15.0 through 0.15.9 contains an OS command injection vulnerability that allows attackers to run shell commands through improperly escaped single quotes in format_command. Attackers can plant a file with a crafted name containing an apostrophe so that triggering an action like the default edit action executes commands with victim privileges. |
| Use of a less trusted source in the DKIM signing of Progressive Robot hMailServer 6.0.0 through 6.3.6 allows a remote unauthenticated attacker to have mail they write signed with the DKIM key of a domain the server hosts, so that it passes DKIM and DMARC for that domain at other receivers. With DKIM signing enabled for a hosted domain, the server signed every message on its first delivery pass as the domain named in its From header, before local delivery, whatever the message's origin and without checking that its sender had authenticated. A sender anywhere could therefore send the server, as ordinary inbound mail, a message whose From is any address at such a domain, and the server signed it with that domain's key. Every copy the server then sent on to an address outside carried a valid signature aligned with the forged From, whatever the domain's DMARC policy: an account's forward, a mail rule's forward or copy, a Sieve redirect, an alias or distribution list with an outside member, the mirror copy, a managed-list or journal copy, or a message released from quarantine. A signed copy can also be re-sent to other recipients while the domain's key is unchanged. Exploitation needs DKIM signing to be enabled for the hosted domain (it is off until configured) and, for the forgery to leave the server, a forward, alias, list or rule that carries the domain's mail to an outside address. The signer likewise signed a message submitted over authenticated SMTP as whatever hosted domain its From header named, a header authenticated SMTP does not hold to the submitting account, so that an account of one hosted domain could have mail written in the name of another hosted domain signed with that domain's key; this mattered where the server holds signed-in senders to their own envelope addresses (SmtpAuthenticatedSenderCheck, off by default), as the signature was then the remaining way for such mail to pass the other domain's DMARC policy. |
| Unchecked input for a loop condition in Progressive Robot hMailServer 6.0.0 through 6.3.6 allows a remote unauthenticated attacker to stop the server carrying mail. The server bounds the mail it generates in response to a message - a rule forward, reply or copy, an account forward, a Sieve redirect, vacation or notify, a bounce, an out-of-office reply - by a counter it carries in the message's X-hMailServer-LoopCount header, and makes no more once the counter reaches the configured rule loop limit (5 by default); that is what ends a forwarding or auto-reply cycle in a bounded number of hops. X-hMailServer-LoopCount is an ordinary header that is not stripped from mail arriving from outside, and the server read it with a signed conversion and no validation, so a count below zero passed every test against the limit: a sender who sets X-hMailServer-LoopCount to a negative value, or on the Linux builds to a value above the 32-bit signed range that the conversion wraps to a negative one, lifts the bound, and a message that enters a generated-mail cycle then loops up to about two thousand million times, each hop a queued message and a delivery, filling the queue and disk and stopping mail service. The Sieve notify action (from 6.2.22) consulted no limit at all, and its increment of the count could overflow a signed integer; and an account could reset the counter on its own mail through a Sieve editheader of the header (from 6.2.22) or a rule Set header value action (all versions) ahead of a forward or redirect. |
