| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: fix tx ident leak for commands without a response
Commit 6c3ea155e5ee ("Bluetooth: L2CAP: Fix not tracking outstanding
TX ident") changed ident allocation to use an IDA, releasing idents in
l2cap_put_ident() when the matching response command is received.
But identifiers allocated for commands that have no response defined
are never released. In particular L2CAP_LE_CREDITS is sent repeatedly for
the lifetime of an LE CoC channel, so a peer streaming data to the
host exhausts the 1-255 ident range after 254 credit packets. From
then on l2cap_get_ident() fails:
kernel: Bluetooth: Unable to allocate ident: -28
and every subsequent L2CAP_LE_CREDITS packet is sent with ident 0,
which is invalid (Core Spec, Vol 3, Part A, Section 4: "Signaling
identifier 0x00 is an invalid identifier and shall never be used in
any command"). Remote stacks that validate the ident drop these
commands, never receive new credits, and the channel stalls
permanently. With default socket buffers this happens after roughly 0.5 MB
of received data (the exact amount depends on the socket receive buffer):
< ACL Data TX: Handle 2048 flags 0x00 dlen 12
LE L2CAP: LE Flow Control Credit (0x16) ident 0 len 4
Source CID: 64
Credits: 1
Release the ident immediately after sending L2CAP_LE_CREDITS since no
response will ever release it. Use a local variable instead of
chan->ident so that an ident that an EXT_FLOWCTL channel may be waiting on
(e.g. a pending reconfigure) is not overwritten by a credit packet.
Also add the missing L2CAP_LE_CONN_RSP case to l2cap_put_ident() so
idents allocated for outgoing L2CAP_LE_CONN_REQ commands are released
when the response arrives. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_pedit: fix TOCTOU heap OOB write in tc offload
There is a TOCTOU race condition in flower lockless approach between sizing
a flow_rule buffer and filling it.
zdi-disclosures@trendmicro.com reports:
The cls_flower classifier operates with TCF_PROTO_OPS_DOIT_UNLOCKED
(fl_change runs without RTNL), while RTM_NEWACTION holds RTNL, so the
independent locking domains make the race reachable in practice. KASAN
confirms:
BUG: KASAN: slab-out-of-bounds in tcf_pedit_offload_act_setup+0x81b/0x930
Write of size 4 at addr ffff888001f27520 by task poc-toctou/312
The buggy address is located 0 bytes to the right of
allocated 288-byte region [ffff888001f27400, ffff888001f27520)
(cache kmalloc-512)
Note: The result is a heap OOB write attacker-controlled content into the
adjacent slab object (requires CAP_NET_ADMIN).
The fix introduces reading tcfp_nkeys under act->tcfa_lock in all places
using a new tcf_pedit_nkeys_locked() which replaces the old tcf_pedit_nkeys().
Additionally we close the remaining TOCTOU window between the sizing read and
the fill reads by more careful accounting.
Rather than silently truncating the key count, which leads to incorrect
action semantics offloaded to hardware and secondary OOB writes if
the remaining capacity is zero or consumed by prior actions, we enforce
remaining capacity checks and return -ENOSPC if the required space exceeds
the remaining capacity. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix writeback error handling
Fix the error handling in writeback_iter() loop. If an error occurs,
writeback_iter() needs to be called again with *error set to the error so
that it can clean up iteration state. Further, the current folio needs
unlocking and redirtying. |
| In the Linux kernel, the following vulnerability has been resolved:
net: microchip: vcap: fix races on the shared Super VCAP block
The VCAP instances on a chip are not independent, yet they are locked
independently. On sparx5 and lan969x the IS0 and IS2 instances are
backed by the same Super VCAP hardware block and share its cache and
command registers: every access drives the shared VCAP_SUPER_CTRL
register and moves data through the shared cache registers.
Accessing one instance therefore races with accessing another. The
per-instance admin->lock cannot prevent this, as each instance takes a
different lock.
The locking issue is mostly disguised by the fact that the core usage of
the vcap api runs under rtnl. However, the full rule dump in debugfs
decodes rules straight from hardware (a READ command followed by a cache
read) and runs outside rtnl, so it races a concurrent tc-flower rule
write to another Super VCAP instance.
Besides corrupting the dump, the read repopulates the shared cache
between the writers cache fill and its write command, so the writer
commits the wrong data and corrupts the hardware entry.
Introduce vcap_lock() and vcap_unlock() helpers and route every rule
lock site in the VCAP API and its debugfs code through them. Replace the
per-instance admin->lock with a single mutex in struct vcap_control that
serializes access to all instances. The helpers reach it through a new
admin->vctrl back-pointer, and the clients initialise and destroy the
control lock instead of a per-instance one.
No path holds more than one instance lock, so collapsing them onto a
single mutex cannot self-deadlock. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: avoid stale runlist element dereference in fallocate
ntfs_attr_fallocate() allocates holes and delayed allocations inside
initialized size by looking up the current runlist element under
ni->runlist.lock. The returned struct runlist_element is only a borrowed
pointer into ni->runlist.rl. A writer can replace and free that array
after the read lock is dropped, so later reads of rl->lcn, rl->length and
rl->vcn can touch freed memory.
The buggy scenario involves two paths, with each column showing the order
within that path:
ntfs_attr_fallocate():
1. Take ni->runlist.lock for read.
2. Get rl from ntfs_attr_find_vcn_nolock().
3. Drop ni->runlist.lock.
4. Read rl->lcn, rl->length and rl->vcn.
mmap page_mkwrite:
1. Enter ntfs_filemap_page_mkwrite().
2. Reach __ntfs_write_iomap_begin() and ntfs_attr_map_cluster().
3. Merge allocation state with ntfs_runlists_merge().
4. Reallocate ni->runlist.rl in ntfs_rl_realloc(), freeing the old array.
Validation reproduced this kernel report:
BUG: KASAN: slab-use-after-free in ntfs_attr_fallocate+0xbb8/0xd00
Call Trace:
<TASK>
dump_stack_lvl+0x66/0xa0
print_report+0xce/0x630
? ntfs_attr_fallocate+0xbb8/0xd00
? srso_alias_return_thunk+0x5/0xfbef5
? __virt_addr_valid+0x20d/0x410
? ntfs_attr_fallocate+0xbb8/0xd00
kasan_report+0xe0/0x110
? ntfs_attr_fallocate+0xbb8/0xd00
ntfs_attr_fallocate+0xbb8/0xd00
? lock_acquire+0x2b8/0x2f0
? __pfx_ntfs_attr_fallocate+0x10/0x10
? 0xffffffffc0000095
? down_write+0x10d/0x1e0
ntfs_fallocate+0x5c9/0x1d00
? __pfx_ntfs_fallocate+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? lock_acquire+0x2b8/0x2f0
? srso_alias_return_thunk+0x5/0xfbef5
? selinux_file_permission+0x3a7/0x510
vfs_fallocate+0x29d/0xd30
__x64_sys_fallocate+0xc7/0x150
? do_syscall_64+0x81/0x6a0
do_syscall_64+0x115/0x6a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Allocated by task 410:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0xaa/0xb0
__kvmalloc_node_noprof+0x353/0x920
ntfs_rl_realloc+0x3f/0x110
ntfs_runlists_merge+0xaa3/0x3010
ntfs_attr_map_cluster+0x4e5/0xf80
ntfs_attr_fallocate+0x53f/0xd00
ntfs_fallocate+0x5c9/0x1d00
vfs_fallocate+0x29d/0xd30
__x64_sys_fallocate+0xc7/0x150
do_syscall_64+0x115/0x6a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 424:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x5f/0x80
kfree+0x307/0x580
ntfs_rl_realloc+0x6f/0x110
ntfs_runlists_merge+0x7b1/0x3010
ntfs_attr_map_cluster+0x4e5/0xf80
__ntfs_write_iomap_begin+0x8cd/0x2280
iomap_iter+0x6de/0x11e0
iomap_page_mkwrite+0x391/0x650
ntfs_filemap_page_mkwrite+0x1ac/0x400
do_page_mkwrite+0x15c/0x280
__handle_mm_fault+0xd6d/0x1ca0
handle_mm_fault+0x19c/0x470
do_user_addr_fault+0x23b/0x9c0
exc_page_fault+0x5c/0xc0
asm_exc_page_fault+0x26/0x30
Fix this by copying the needed runlist fields while the read lock is still
held and using only those scalar snapshots after unlocking.
After the snapshot, ntfs_attr_map_cluster() can also find that the range
is already mapped and return balloc=false. Only call ntfs_dio_zero_range()
when new clusters were allocated, matching the write iomap path and
preserving the zero-newly-allocated-holes behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: avoid stale runlist element dereference in MFT writeback
ntfs_write_mft_block() maps each $MFT record through the $MFT data
runlist. For sub-folio clusters it looks up a struct runlist_element under
ni->runlist.lock, drops the lock, and later uses rl->length and rl->vcn
when choosing folio_sz.
That pointer is only borrowed from ni->runlist.rl. Concurrent $MFT
allocation extension can merge a replacement runlist under the same lock,
and ntfs_rl_realloc() can free the old backing array. If that happens
between the lookup and the later folio_sz decision, writeback can
dereference freed runlist storage.
The buggy scenario involves two paths, with each column showing the order
within that path:
MFT writeback path: $MFT allocation extension:
1. Look up rl under 1. Extend the $MFT data allocation.
ni->runlist.lock. 2. Publish a replacement runlist.
2. Drop ni->runlist.lock. 3. Free the old runlist array.
3. Read rl->length and rl->vcn
to choose folio_sz.
Compute the remaining run length while ni->runlist.lock is still held, and
use that scalar after unlock. This preserves the existing folio sizing
decision without carrying a borrowed runlist_element across the lock
boundary.
Validation reproduced this kernel report:
BUG: KASAN: slab-use-after-free in ntfs_mft_writepages+0x1c8d/0x1fb0
Call Trace:
<TASK>
dump_stack_lvl+0x66/0xa0
print_report+0xce/0x630
? ntfs_mft_writepages+0x1c8d/0x1fb0
? srso_alias_return_thunk+0x5/0xfbef5
? __virt_addr_valid+0x20d/0x410
? ntfs_mft_writepages+0x1c8d/0x1fb0
kasan_report+0xe0/0x110
? ntfs_mft_writepages+0x1c8d/0x1fb0
ntfs_mft_writepages+0x1c8d/0x1fb0
? __pfx_ntfs_mft_writepages+0x10/0x10
? __pfx___mutex_unlock_slowpath+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? iput+0x92/0xa80
do_writepages+0x219/0x530
? __pfx_do_writepages+0x10/0x10
__writeback_single_inode+0x117/0xf50
? do_raw_spin_lock+0x130/0x270
? __pfx_do_raw_spin_lock+0x10/0x10
? __pfx___writeback_single_inode+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
writeback_sb_inodes+0x65b/0x1810
? srso_alias_return_thunk+0x5/0xfbef5
? lock_acquire+0x2b8/0x2f0
? __pfx_writeback_sb_inodes+0x10/0x10
? lock_release+0x1e0/0x280
? _raw_spin_unlock+0x23/0x40
? move_expired_inodes+0x2b8/0x850
__writeback_inodes_wb+0xf4/0x270
? __pfx___writeback_inodes_wb+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? queue_io+0x2e4/0x410
wb_writeback+0x666/0x880
? srso_alias_return_thunk+0x5/0xfbef5
? __pfx_wb_writeback+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
? get_nr_dirty_inodes+0x1c/0x170
wb_workfn+0x75e/0xbb0
? srso_alias_return_thunk+0x5/0xfbef5
? _raw_spin_unlock_irqrestore+0x27/0x60
? __pfx_wb_workfn+0x10/0x10
? __pfx_debug_object_deactivate+0x10/0x10
? lock_acquire+0x2b8/0x2f0
? srso_alias_return_thunk+0x5/0xfbef5
? lock_release+0x1e0/0x280
process_one_work+0x8d0/0x1870
? __pfx_process_one_work+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
worker_thread+0x575/0xf80
? __pfx_worker_thread+0x10/0x10
kthread+0x2e7/0x3c0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x576/0x810
? __pfx_ret_from_fork+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? __switch_to+0x57e/0xe10
? __switch_to_asm+0x33/0x70
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 970:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0xaa/0xb0
__kvmalloc_node_noprof+0x353/0x920
ntfs_rl_realloc+0x3c/0x80
ntfs_runlists_merge+0x1212/0x3010
ntfs_mft_data_extend_allocation_nolock+0x3e0/0x1f40
ntfs_mft_record_alloc+0x1ab4/0x4f10
__ntfs_create+0x680/0x2e50
ntfs_create+0x1e6/0x3a0
path_openat+0x2b55/0x3c10
do_file_open+0x1f4/0x460
do_sys_openat2+0xde/0x170
__x64_sys_openat+0x122/0x1e0
do_syscall_64+0x115/0x6a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 1294:
kasan_save_
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
uprobes/x86: Use proper mm_struct in __in_uprobe_trampoline
In the unregister path we use __in_uprobe_trampoline check with
current->mm for the VMA lookup, which is wrong, because we are
in the tracer context, not the traced process.
Add mm_struct pointer argument to __in_uprobe_trampoline and
changing related callers to pass proper mm_struct pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/pf: Don't attempt to process FAST_REQ or EVENT relays
Currently defined VF/PF relay actions use regular REQUEST messages
only and the PF shouldn't attempt to handle FAST_REQUEST nor EVENT
messages as this would result in breaking the VFPF ABI protocol
and also might trigger an assert on the PF side.
(cherry picked from commit 1714d360fc5ae2e0886a69e979095d9c7ff3568a) |
| In the Linux kernel, the following vulnerability has been resolved:
cachefiles: Fix double unlock in nomem_d_alloc error path
When start_creating() fails and returns -ENOMEM, it has already
released the parent directory lock in __start_dirop():
static struct dentry *__start_dirop(...)
{
...
inode_lock_nested(dir, I_MUTEX_PARENT);
dentry = lookup_one_qstr_excl(name, parent, lookup_flags);
if (IS_ERR(dentry))
inode_unlock(dir); <-- Lock released on error
return dentry;
}
However, the nomem_d_alloc error path in cachefiles_get_directory()
unconditionally calls inode_unlock(d_inode(dir)) again, causing a
double unlock that corrupts the rwsem state.
This is a leftover from commit 7ab96df840e60 which replaced manual
locking with start_creating() but failed to update the nomem_d_alloc
path (while correctly updating mkdir_error and lookup_error paths). |
| In the Linux kernel, the following vulnerability has been resolved:
minix: avoid overflow in bitmap block count calculation
minix_check_superblock() uses minix_blocks_needed() to verify that the
on-disk imap and zmap block counts are large enough for the advertised
inode and zone counts.
The helper currently performs DIV_ROUND_UP() in unsigned int arithmetic.
A Minix v3 image can set s_ninodes or s_zones near UINT_MAX so the
addition inside DIV_ROUND_UP() wraps to zero. That makes a zero imap/zmap
block count look valid, after which minix_fill_super() can dereference
s_imap[0] or s_zmap[0] even though no bitmap buffers were allocated.
Impact: mounting a crafted Minix v3 image whose s_ninodes or s_zones is
near UINT_MAX makes minix_check_superblock() accept a zero bitmap-block
count and minix_fill_super() dereference s_imap[0]/s_zmap[0], panicking
the kernel.
The divisor is the bitmap capacity in bits, blocksize * 8, which is
always a power of two: minix_fill_super() obtains the block size through
sb_set_blocksize(), and blk_validate_block_size() rejects any size that
is not a power of two. Use DIV_ROUND_UP_POW2(), which divides before
adding the round-up term and so cannot overflow for a power-of-two
divisor. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus) Fix passing events to regulator core
Sashiko reports:
Commit 754bd2b4a084 ("hwmon: (pmbus/core) Protect regulator operations with
mutex") introduced a worker to batch regulator events over time using
atomic_or(). The delayed worker then passes the combined bitmask unmodified
to regulator_notifier_call_chain().
The core regulator subsystem's regulator_handle_critical() function
evaluates the event parameter using a strict switch statement. If
multiple distinct faults occur before the worker runs (e.g.,
REGULATOR_EVENT_UNDER_VOLTAGE | REGULATOR_EVENT_OVER_CURRENT), the combined
bitmask fails to match any case. This leaves the reason as NULL and
completely bypasses the critical hw_protection_trigger().
Fix the problem by passing events bit by bit to the regulator event
handler. |
| In the Linux kernel, the following vulnerability has been resolved:
irqchip/ts4800: Fix missing chained handler cleanup on remove
The driver installs a chained handler for the parent interrupt during probe
using irq_set_chained_handler_and_data(), but the remove function does not
clear this handler. This leaves a dangling handler that may be called when
the parent interrupt fires after the driver has been removed, potentially
accessing freed memory and causing a kernel crash.
Additionally, the parent_irq obtained via irq_of_parse_and_map() is not
stored, making it inaccessible in the remove function. Moreover, interrupt
mappings created during probe are not properly disposed.
Fix this by:
- Saving parent_irq in probe
- Clearing the chained handler with NULL in ts4800_ic_remove()
- Disposing all IRQ mappings before domain removal to prevent resource
leaks |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_teql: Introduce slaves_lock to avoid race condition and UAF
The teql master->slaves singly linked list is not protected against
multiple writes. It can be mod'ed concurently from teql_master_xmit(),
teql_dequeue(), teql_init() and teql_destroy() without holding any list
lock or RCU protection.
zdi-disclosures@trendmicro.com has demonstrated that the qdisc is freed
after an RCU grace period, but teql_master_xmit() running on another
CPU can still hold a stale pointer into the list, resulting in a
slab-use-after-free:
BUG: KASAN: slab-use-after-free in teql_master_xmit+0xf0f/0x16b0
Read of size 8 at addr ffff888013fb0440 by task poc/332
Freed 512-byte region [ffff888013fb0400, ffff888013fb0600) (kmalloc-512)
The fix?
Add a per-master slaves_lock spinlock that serializes all mutations of
master->slaves and the NEXT_SLAVE() links in teql_destroy() and
teql_qdisc_init(). teql_master_xmit() also takes the same slaves_lock
around those updates.
Annotate master->slaves and the per-slave ->next pointer with __rcu and
use the appropriate RCU accessors everywhere they are touched:
rcu_assign_pointer() on the writer side (under slaves_lock),
rcu_dereference_protected() for the writer-side loads (also under
slaves_lock), rcu_dereference_bh() for the loads in teql_master_xmit() and
rtnl_dereference() for the loads in teql_master_open()/teql_master_mtu(),
which run under RTNL.
Pair this with rcu_read_lock_bh()/rcu_read_unlock_bh() around the list
traversal in teql_master_xmit(), so that readers either observe a fully
linked list or are deferred until the in-flight mutation completes. The two
early-return paths in teql_master_xmit() are updated to release the RCU-bh
read-side critical section before returning, since leaving it held would
disable BH on that CPU for good. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: sfp: free mii_bus in sfp_i2c_mdiobus_destroy
sfp_i2c_mdiobus_create() allocates the I2C MDIO bus with mdio_i2c_alloc(),
a plain (non-devm) allocation, and registers it. sfp_i2c_mdiobus_destroy()
only unregisters the bus and clears sfp->i2c_mii without calling
mdiobus_free(). As the only reference to the bus is then cleared, the
struct mii_bus is leaked.
This is hit whenever a copper/RollBall SFP module that instantiated an MDIO
bus is removed: sfp_sm_main() takes the global teardown path and calls
sfp_i2c_mdiobus_destroy(). sfp_cleanup(), on driver unbind, frees
sfp->i2c_mii directly, which is why the leak only triggered on module
hot-removal and not on unbind.
Free the bus in sfp_i2c_mdiobus_destroy() to match the allocation done in
sfp_i2c_mdiobus_create(). |
| In the Linux kernel, the following vulnerability has been resolved:
eth: fbnic: don't cache shinfo across skb realloc
fbnic_tx_lso() calls skb_cow_head() which may reallocate the skb
including the shared info. We can't use the pointer calculated
before the call.
BUG: KASAN: slab-use-after-free in fbnic_tx_lso.isra.0+0x668/0x8e0
Read of size 4 at addr ff110000262edd98 by task swapper/5/0
Call Trace:
fbnic_tx_lso.isra.0+0x668/0x8e0
fbnic_xmit_frame+0x622/0xba0
dev_hard_start_xmit+0xf4/0x620
Allocated by task 8653:
__alloc_skb+0x11e/0x5f0
alloc_skb_with_frags+0xcc/0x6c0
sock_alloc_send_pskb+0x327/0x3f0
__ip_append_data+0x188b/0x47a0
ip_make_skb+0x24a/0x300
udp_sendmsg+0x14d2/0x21e0
Freed by task 0:
kfree+0x123/0x5a0
pskb_expand_head+0x36c/0xfa0
fbnic_tx_lso.isra.0+0x500/0x8e0
fbnic_xmit_frame+0x622/0xba0
dev_hard_start_xmit+0xf4/0x620
sch_direct_xmit+0x25b/0x1100
The buggy address belongs to the object at ff110000262edc40
which belongs to the cache skbuff_small_head of size 640
The buggy address is located 344 bytes inside of
freed 640-byte region [ff110000262edc40, ff110000262ede |
| In the Linux kernel, the following vulnerability has been resolved:
net: sungem: fix probe error cleanup
gem_init_one() calls gem_remove_one() when register_netdev() fails.
gem_remove_one() unregisters and frees resources owned by the net_device,
including the DMA block, MMIO mapping, PCI regions, and the net_device
itself. gem_init_one() then falls through to its own cleanup labels and
frees the same resources again.
Keep the register_netdev() error path in gem_init_one(): clear drvdata so
PM/remove paths do not see a half-registered device, remove the NAPI
instance added during probe, and let the existing cleanup labels release
the resources once.
The issue was found by a local static-analysis checker for probe error
paths. The reported path was manually inspected before sending this fix.
Compile-tested with CONFIG_SUNGEM=y. Runtime testing was not performed
because no sungem hardware is available. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/mm: Fix handling of _PAGE_UNUSED pte bit
The _PAGE_UNUSED softbit should not really be lying around. Its sole
purpose is to signal to try_to_unmap_one() and try_to_migrate_one()
that the page can be discarded instead of being moved / swapped.
KVM has no way to know why a page is being unmapped, so it sets the bit
on userspace ptes corresponding to unused guest pages every time they
get unmapped. KVM has no reasonable way to clear the bit once the page
is in use again.
While set_ptes() checks and clears the bit, other paths that set new
ptes did not. This led to used pages being thrown out as if they were
unused, causing guest corruption.
Fix the issue by clearing the _PAGE_UNUSED bit for present ptes in
set_pte(), i.e. whenever a present pte is getting set. The check in
set_ptes() is then redundant and can be removed.
Also fix gmap_helper_try_set_pte_unused() to only set the bit if the
pte is present; the _PAGE_UNUSED bit is only defined for present ptes
and thus should not be set for non-present ptes. |
| In the Linux kernel, the following vulnerability has been resolved:
alloc_tag: fix use-after-free in /proc/allocinfo after module unload
allocinfo_start() only reinitializes the codetag iterator at position 0.
For subsequent reads (position > 0), it reuses cached iterator state from
the previous batch. allocinfo_stop() drops mod_lock between read batches,
which allows module unload to complete and free the module memory that the
cached iterator still references:
CPU0 (read) CPU1 (rmmod)
---- ----
allocinfo_start(pos=0)
down_read(mod_lock)
allocinfo_show()
...
allocinfo_stop()
up_read(mod_lock)
codetag_unload_module()
kfree(cmod)
release_module_tags()
...
free_mod_mem()
allocinfo_start(pos=N)
down_read(mod_lock)
// reuses cached iter, skips re-init
allocinfo_show()
ct->filename <-- UAF
After free_mod_mem() frees the module's .rodata, allocinfo_show()
dereferences ct->filename, ct->function which point there.
Save the iterator state in allocinfo_next() and resume from it in
allocinfo_start() with codetag_next_ct(), which detects module removal via
idr_find() returning NULL and skips to the next module. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix insn_aux_data leak on verifier err_free_env path
When bpf_check() allocates env->insn_aux_data successfully but later
fails to allocate env->succ, it jumps directly to err_free_env.
The existing vfree(env->insn_aux_data) sits before the err_free_env
label, so that direct jump bypasses it and leaks insn_aux_data.
Move vfree(env->insn_aux_data) into err_free_env so all early and late
exit paths release it consistently. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Kill MIDI 2.0 URBs before freeing endpoints
MIDI 2.0 input URBs are started during snd_usb_midi_v2_create(). A
later setup failure can still jump to snd_usb_midi_v2_free(), which
currently frees each endpoint and its coherent URB buffers without first
stopping the submitted URBs. A completion can then dereference the
embedded URB context and endpoint state after they have been freed, or
try to resubmit from the stale endpoint.
This was observed as a KASAN slab-use-after-free in
input_urb_complete().
The buggy scenario involves two paths, with each column showing the order
within that path:
probe error path: USB completion path:
1. start_input_streams() submits 1. The HCD still owns a
input URBs. submitted input URB.
2. A later setup helper returns 2. input_urb_complete() runs
an error. with urb->context in ep.
3. snd_usb_midi_v2_free() frees 3. The completion reads ep
endpoint storage and URB buffers. state and can requeue URBs.
Make the endpoint destructor follow the same teardown ordering used for
disconnect when the endpoint has not already been disconnected: publish
ep->disconnected, kill the URBs synchronously, and drain the endpoint
before freeing URB buffers and endpoint storage. The guard avoids
repeating the stop sequence after the normal
snd_usb_midi_v2_disconnect_all() path, while still synchronizing the
direct MIDI 2.0 create-error free path.
Validation reproduced this kernel report:
BUG: KASAN: slab-use-after-free in input_urb_complete+0x37/0x1b0
Workqueue: usb_hub_wq hub_event
RIP: 0010:_raw_spin_unlock_irq+0x2e/0x50
Read of size 8
Call trace:
dump_stack_lvl+0x77/0xb0
print_report+0xce/0x5f0
input_urb_complete+0x37/0x1b0 (sound/usb/midi2.c:186)
srso_alias_return_thunk+0x5/0xfbef5
__virt_addr_valid+0x19f/0x330
kasan_report+0xe0/0x110
__usb_hcd_giveback_urb+0x112/0x1d0
dummy_timer+0xaaa/0x19a0
lock_is_held_type+0x9a/0x110
__lock_acquire+0x467/0x28b0
mark_held_locks+0x40/0x70
_raw_spin_unlock_irqrestore+0x44/0x60
lockdep_hardirqs_on_prepare+0xbb/0x1a0
__hrtimer_run_queues+0x101/0x520
hrtimer_run_softirq+0xd0/0x130
handle_softirqs+0x15b/0x670
__irq_exit_rcu+0xd0/0x170
irq_exit_rcu+0xe/0x20
sysvec_apic_timer_interrupt+0x6c/0x80
asm_sysvec_apic_timer_interrupt+0x1a/0x20 |
