| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dpu: fix mismatch between power and frequency
During DPU runtime suspend, calling dev_pm_opp_set_rate(dev, 0) drops
the MMCX rail to MIN_SVS while the core clock frequency remains at its
original (highest) rate. When runtime resume re-enables the clock, this
may result in a mismatch between the rail voltage and the clock rate.
For example, in the DPU bind path, the sequence could be:
cpu0: dev_sync_state -> rpmhpd_sync_state
cpu1: dpu_kms_hw_init
timeline 0 ------------------------------------------------> t
After rpmhpd_sync_state, the voltage performance is no longer guaranteed
to stay at the highest level. During dpu_kms_hw_init, calling
dev_pm_opp_set_rate(dev, 0) drops the voltage, causing the MMCX rail to
fall to MIN_SVS while the core clock is still at its maximum frequency.
When the power is re-enabled, only the clock is enabled, leading to a
situation where the MMCX rail is at MIN_SVS but the core clock is at its
highest rate. In this state, the rail cannot sustain the clock rate,
which may cause instability or system crash.
Remove the call to dev_pm_opp_set_rate(dev, 0) from dpu_runtime_suspend
to ensure the correct vote is restored when DPU resumes.
Patchwork: https://patchwork.freedesktop.org/patch/710077/ |
| In the Linux kernel, the following vulnerability has been resolved:
net: psp: check for device unregister when creating assoc
psp_assoc_device_get_locked() obtains a psp_dev reference via
psp_dev_get_for_sock() (which uses psp_dev_tryget() under RCU);
it then acquires psd->lock and drops the reference. Before
the lock is taken, psp_dev_unregister() can run to completion:
take psd->lock, clear out state, unlock, drop the registration
reference.
The expectation is that the lock prevents device unregistration,
but much like with netdevs special care has to be taken when
"upgrading" a reference to a locked device. Add the missing
check if device is still alive. psp_dev_is_registered() exists
already but had no callers, which makes me wonder if I either
forgot to add this or lost the check during refactoring... |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: tegra194: Fix CBB timeout caused by DBI access before core power-on
When PERST# is deasserted twice (assert -> deassert -> assert -> deassert),
a CBB (Control Backbone) timeout occurs at DBI register offset 0x8bc
(PCIE_MISC_CONTROL_1_OFF). This happens because pci_epc_deinit_notify()
and dw_pcie_ep_cleanup() are called before reset_control_deassert() powers
on the controller core.
The call chain that causes the timeout:
pex_ep_event_pex_rst_deassert()
pci_epc_deinit_notify()
pci_epf_test_epc_deinit()
pci_epf_test_clear_bar()
pci_epc_clear_bar()
dw_pcie_ep_clear_bar()
__dw_pcie_ep_reset_bar()
dw_pcie_dbi_ro_wr_en() <- Accesses 0x8bc DBI register
reset_control_deassert(pcie->core_rst) <- Core powered on HERE
The DBI registers, including PCIE_MISC_CONTROL_1_OFF (0x8bc), are only
accessible after the controller core is powered on via
reset_control_deassert(pcie->core_rst). Accessing them before this point
results in a CBB timeout because the hardware is not yet operational.
Fix this by moving pci_epc_deinit_notify() and dw_pcie_ep_cleanup() to
after reset_control_deassert(pcie->core_rst), ensuring the controller is
fully powered on before any DBI register accesses occur. |
| Pi is a minimal terminal coding harness. From 0.74.0 until 0.78.1, Pi stored API keys and OAuth credentials in auth.json. A race condition in the file write path could briefly create or rewrite this file with permissions derived from the process umask before tightening the file to owner-only permissions. This vulnerability is fixed in 0.78.1. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Fix af_unix null-ptr-deref in proto update
unix_stream_connect() sets sk_state (`WRITE_ONCE(sk->sk_state,
TCP_ESTABLISHED)`) _before_ it assigns a peer (`unix_peer(sk) = newsk`).
sk_state == TCP_ESTABLISHED makes sock_map_sk_state_allowed() believe that
socket is properly set up, which would include having a defined peer. IOW,
there's a window when unix_stream_bpf_update_proto() can be called on
socket which still has unix_peer(sk) == NULL.
CPU0 bpf CPU1 connect
-------- ------------
WRITE_ONCE(sk->sk_state, TCP_ESTABLISHED)
sock_map_sk_state_allowed(sk)
...
sk_pair = unix_peer(sk)
sock_hold(sk_pair)
sock_hold(newsk)
smp_mb__after_atomic()
unix_peer(sk) = newsk
BUG: kernel NULL pointer dereference, address: 0000000000000080
RIP: 0010:unix_stream_bpf_update_proto+0xa0/0x1b0
Call Trace:
sock_map_link+0x564/0x8b0
sock_map_update_common+0x6e/0x340
sock_map_update_elem_sys+0x17d/0x240
__sys_bpf+0x26db/0x3250
__x64_sys_bpf+0x21/0x30
do_syscall_64+0x6b/0x3a0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Initial idea was to move peer assignment _before_ the sk_state update[1],
but that involved an additional memory barrier, and changing the hot path
was rejected.
Then a NULL check during proto update in unix_stream_bpf_update_proto() was
considered[2], but the follow-up discussion[3] focused on the root cause,
i.e. sockmap update taking a wrong lock. Or, more specifically, missing
unix_state_lock()[4].
In the end it was concluded that teaching sockmap about the af_unix locking
would be unnecessarily complex[5].
Complexity aside, since BPF_PROG_TYPE_SCHED_CLS and BPF_PROG_TYPE_SCHED_ACT
are allowed to update sockmaps, sock_map_update_elem() taking the unix
lock, as it is currently implemented in unix_state_lock():
spin_lock(&unix_sk(s)->lock), would be problematic. unix_state_lock() taken
in a process context, followed by a softirq-context TC BPF program
attempting to take the same spinlock -- deadlock[6].
This way we circled back to the peer check idea[2].
[1]: https://lore.kernel.org/netdev/ba5c50aa-1df4-40c2-ab33-a72022c5a32e@rbox.co/
[2]: https://lore.kernel.org/netdev/20240610174906.32921-1-kuniyu@amazon.com/
[3]: https://lore.kernel.org/netdev/7603c0e6-cd5b-452b-b710-73b64bd9de26@linux.dev/
[4]: https://lore.kernel.org/netdev/CAAVpQUA+8GL_j63CaKb8hbxoL21izD58yr1NvhOhU=j+35+3og@mail.gmail.com/
[5]: https://lore.kernel.org/bpf/CAAVpQUAHijOMext28Gi10dSLuMzGYh+jK61Ujn+fZ-wvcODR2A@mail.gmail.com/
[6]: https://lore.kernel.org/bpf/dd043c69-4d03-46fe-8325-8f97101435cf@linux.dev/
Summary of scenarios where af_unix/stream connect() may race a sockmap
update:
1. connect() vs. bpf(BPF_MAP_UPDATE_ELEM), i.e. sock_map_update_elem_sys()
Implemented NULL check is sufficient. Once assigned, socket peer won't
be released until socket fd is released. And that's not an issue because
sock_map_update_elem_sys() bumps fd refcnf.
2. connect() vs BPF program doing update
Update restricted per verifier.c:may_update_sockmap() to
BPF_PROG_TYPE_TRACING/BPF_TRACE_ITER
BPF_PROG_TYPE_SOCK_OPS (bpf_sock_map_update() only)
BPF_PROG_TYPE_SOCKET_FILTER
BPF_PROG_TYPE_SCHED_CLS
BPF_PROG_TYPE_SCHED_ACT
BPF_PROG_TYPE_XDP
BPF_PROG_TYPE_SK_REUSEPORT
BPF_PROG_TYPE_FLOW_DISSECTOR
BPF_PROG_TYPE_SK_LOOKUP
Plus one more race to consider:
CPU0 bpf CPU1 connect
-------- ------------
WRITE_ONCE(sk->sk_state, TCP_ESTABLISHED)
sock_map_sk_state_allowed(sk)
sock_hold(newsk)
smp_mb__after_atomic()
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: avoid reading already updated pages during GC
We found the following issue during fuzz testing:
page: refcount:3 mapcount:0 mapping:00000000b6e89c65 index:0x18b2dc pfn:0x161ba9
memcg:f8ffff800e269c00
aops:f2fs_meta_aops ino:2
flags: 0x52880000000080a9(locked|waiters|uptodate|lru|private|zone=1|kasantag=0x4a)
raw: 52880000000080a9 fffffffec6e17588 fffffffec0ccc088 a7ffff8067063618
raw: 000000000018b2dc 0000000000000009 00000003ffffffff f8ffff800e269c00
page dumped because: VM_BUG_ON_FOLIO(folio_test_uptodate(folio))
page_owner tracks the page as allocated
post_alloc_hook+0x58c/0x5ec
prep_new_page+0x34/0x284
get_page_from_freelist+0x2dcc/0x2e8c
__alloc_pages_noprof+0x280/0x76c
__folio_alloc_noprof+0x18/0xac
__filemap_get_folio+0x6bc/0xdc4
pagecache_get_page+0x3c/0x104
do_garbage_collect+0x5c78/0x77a4
f2fs_gc+0xd74/0x25f0
gc_thread_func+0xb28/0x2930
kthread+0x464/0x5d8
ret_from_fork+0x10/0x20
------------[ cut here ]------------
kernel BUG at mm/filemap.c:1563!
folio_end_read+0x140/0x168
f2fs_finish_read_bio+0x5c4/0xb80
f2fs_read_end_io+0x64c/0x708
bio_endio+0x85c/0x8c0
blk_update_request+0x690/0x127c
scsi_end_request+0x9c/0xb8c
scsi_io_completion+0xf0/0x250
scsi_finish_command+0x430/0x45c
scsi_complete+0x178/0x6d4
blk_mq_complete_request+0xcc/0x104
scsi_done_internal+0x214/0x454
scsi_done+0x24/0x34
which is similar to the problem reported by syzbot:
https://syzkaller.appspot.com/bug?extid=3686758660f980b402dc
This case is consistent with the description in commit 9bf1a3f
("f2fs: avoid GC causing encrypted file corrupted"):
Page 1 is moved from blkaddr A to blkaddr B by move_data_block, and after
being written it is marked as uptodate. Then, Page 1 is moved from blkaddr
B to blkaddr C, VM_BUG_ON_FOLIO was triggered in the endio initiated by
ra_data_block.
There is no need to read Page 1 again from blkaddr B, since it has already
been updated. Therefore, avoid initiating I/O in this case. |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache: fix dirty mapping checking in passthrough mode switching
As mentioned in commit 9b1cc9f251af ("dm cache: share cache-metadata
object across inactive and active DM tables"), dm-cache assumed table
reload occurs after suspension, while LVM's table preload breaks this
assumption. The dirty mapping check for passthrough mode was designed
around this assumption and is performed during table creation, causing
the check to fail with preload while metadata updates are ongoing. This
risks loading dirty mappings into passthrough mode, resulting in data
loss.
Reproduce steps:
1. Create a writeback cache with zero migration_threshold to produce
dirty mappings
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
dmsetup create cdata --table "0 131072 linear /dev/sdc 8192"
dmsetup create corig --table "0 262144 linear /dev/sdc 262144"
dd if=/dev/zero of=/dev/mapper/cmeta bs=4k count=1 oflag=direct
dmsetup create cache --table "0 262144 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writeback smq \
2 migration_threshold 0"
2. Preload a table in passthrough mode
dmsetup reload cache --table "0 262144 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 passthrough smq 0"
3. Write to the first cache block to make it dirty
fio --filename=/dev/mapper/cache --name=populate --rw=write --bs=4k \
--direct=1 --size=64k
4. Resume the inactive table. Now it's possible to load the dirty block
into passthrough mode.
dmsetup resume cache
Fix by moving the checks to the preresume phase to support table
preloading. Also remove the unused function dm_cache_metadata_all_clean. |
| Ghost is a Node.js content management system. From 6.0.9 until 6.21.1, Ghost’s private-IP check for outbound HTTP requests could be bypassed via DNS rebinding, allowing an attacker to coerce the Ghost server into reaching hosts on internal networks through features that issue external fetches. This vulnerability is fixed in 6.21.1. |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache: fix null-deref with concurrent writes in passthrough mode
In passthrough mode, when dm-cache starts to invalidate a cache
entry and bio prison cell lock fails due to concurrent write to
the same cached block, mg->cell remains NULL. The error path in
invalidate_complete() attempts to unlock and free the cell
unconditionally, causing a NULL pointer dereference:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 UID: 0 PID: 134 Comm: fio Not tainted 6.19.0-rc7 #3 PREEMPT
RIP: 0010:dm_cell_unlock_v2+0x3f/0x210
<snip>
Call Trace:
invalidate_complete+0xef/0x430
map_bio+0x130f/0x1a10
cache_map+0x320/0x6b0
__map_bio+0x458/0x510
dm_submit_bio+0x40e/0x16d0
__submit_bio+0x419/0x870
<snip>
Reproduce steps:
1. Create a cache device
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
dmsetup create cdata --table "0 131072 linear /dev/sdc 8192"
dmsetup create corig --table "0 262144 linear /dev/sdc 262144"
dd if=/dev/zero of=/dev/mapper/cmeta bs=4k count=1 oflag=direct
dmsetup create cache --table "0 262144 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0"
2. Promote the first data block into cache
fio --filename=/dev/mapper/cache --name=populate --rw=write --bs=4k \
--direct=1 --size=64k
3. Reload the cache into passthrough mode
dmsetup suspend cache
dmsetup reload cache --table "0 262144 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 passthrough smq 0"
dmsetup resume cache
4. Write to the first cached block concurrently
fio --filename=/dev/mapper/cache --name test --rw=randwrite --bs=4k \
--randrepeat=0 --direct=1 --numjobs=2 --size 64k
Fix by checking if mg->cell is valid before attempting to unlock it. |
| A flaw in Node.js HTTP Agent can cause a client to accept as valid a response that is send before the client has sent the request.
This vulnerability affects all supported release lines: **Node.js 22**, **Node.js 24**, and **Node.js 26**. |
| A time-to-check-time-of-use in polkit authentication of qSnapper before version 1.3.3 allowed a local attacker to bypass qSnappers authentication mechanism and operate e.g. as root user. |
| AIOHTTP is an asynchronous HTTP client/server framework for asyncio and Python. Prior to 3.14.1, the server_hostname TLS SNI check can be bypassed when an existing connection is reused. If an application makes multiple requests to the same domain, but with different per-request server_hostname parameters, then the later calls may succeed by reusing the existing connection when they should have been rejected due to the TLS SNI check. This vulnerability is fixed in 3.14.1. |
| pam_usb provides hardware authentication for Linux using ordinary removable media. In versions prior to 0.9.2, a symlink race condition exists in per-device and per-user pad directory creation. pam_usb uses a check-then-act pattern: it calls lstat() to test for existence and then calls mkdir() separately to create the directory. A local attacker can win the race between these calls by replacing the target path with a symlink to a directory they control. If successful, one-time pad files may be written to an attacker-controlled location, potentially exposing future pad values before use or disrupting authentication. This issue has been fixed in version 0.9.2. |
| Impact:
Undici's HTTP/1.1 client is vulnerable to response queue poisoning on reused keep-alive sockets. An attacker-controlled upstream server can inject an unsolicited HTTP/1.1 response onto an idle socket after a request completes. When the client dispatches the next request on that socket, it associates the injected response with the new request, causing responses to be delivered to the wrong requests.
This requires an attacker-controlled or compromised upstream HTTP/1.1 server and keep-alive connection reuse.
Patches:
Upgrade to undici v6.26.0, v7.28.0 or v8.5.0.
Workarounds:
Disable keep-alive connection reuse by setting keepAliveTimeout: 0 on the Client or Pool. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/pagewalk: fix race between concurrent split and refault
The splitting of a PUD entry in walk_pud_range() can race with a
concurrent thread refaulting the PUD leaf entry causing it to try walking
a PMD range that has disappeared.
An example and reproduction of this is to try reading numa_maps of a
process while VFIO-PCI is setting up DMA (specifically the
vfio_pin_pages_remote call) on a large BAR for that process.
This will trigger a kernel BUG:
vfio-pci 0000:03:00.0: enabling device (0000 -> 0002)
BUG: unable to handle page fault for address: ffffa23980000000
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP NOPTI
...
RIP: 0010:walk_pgd_range+0x3b5/0x7a0
Code: 8d 43 ff 48 89 44 24 28 4d 89 ce 4d 8d a7 00 00 20 00 48 8b 4c 24
28 49 81 e4 00 00 e0 ff 49 8d 44 24 ff 48 39 c8 4c 0f 43 e3 <49> f7 06
9f ff ff ff 75 3b 48 8b 44 24 20 48 8b 40 28 48 85 c0 74
RSP: 0018:ffffac23e1ecf808 EFLAGS: 00010287
RAX: 00007f44c01fffff RBX: 00007f4500000000 RCX: 00007f44ffffffff
RDX: 0000000000000000 RSI: 000ffffffffff000 RDI: ffffffff93378fe0
RBP: ffffac23e1ecf918 R08: 0000000000000004 R09: ffffa23980000000
R10: 0000000000000020 R11: 0000000000000004 R12: 00007f44c0200000
R13: 00007f44c0000000 R14: ffffa23980000000 R15: 00007f44c0000000
FS: 00007fe884739580(0000) GS:ffff9b7d7a9c0000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffa23980000000 CR3: 000000c0650e2005 CR4: 0000000000770ef0
PKRU: 55555554
Call Trace:
<TASK>
__walk_page_range+0x195/0x1b0
walk_page_vma+0x62/0xc0
show_numa_map+0x12b/0x3b0
seq_read_iter+0x297/0x440
seq_read+0x11d/0x140
vfs_read+0xc2/0x340
ksys_read+0x5f/0xe0
do_syscall_64+0x68/0x130
? get_page_from_freelist+0x5c2/0x17e0
? mas_store_prealloc+0x17e/0x360
? vma_set_page_prot+0x4c/0xa0
? __alloc_pages_noprof+0x14e/0x2d0
? __mod_memcg_lruvec_state+0x8d/0x140
? __lruvec_stat_mod_folio+0x76/0xb0
? __folio_mod_stat+0x26/0x80
? do_anonymous_page+0x705/0x900
? __handle_mm_fault+0xa8d/0x1000
? __count_memcg_events+0x53/0xf0
? handle_mm_fault+0xa5/0x360
? do_user_addr_fault+0x342/0x640
? arch_exit_to_user_mode_prepare.constprop.0+0x16/0xa0
? irqentry_exit_to_user_mode+0x24/0x100
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7fe88464f47e
Code: c0 e9 b6 fe ff ff 50 48 8d 3d be 07 0b 00 e8 69 01 02 00 66 0f 1f
84 00 00 00 00 00 64 8b 04 25 18 00 00 00 85 c0 75 14 0f 05 <48> 3d 00
f0 ff ff 77 5a c3 66 0f 1f 84 00 00 00 00 00 48 83 ec 28
RSP: 002b:00007ffe6cd9a9b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007fe88464f47e
RDX: 0000000000020000 RSI: 00007fe884543000 RDI: 0000000000000003
RBP: 00007fe884543000 R08: 00007fe884542010 R09: 0000000000000000
R10: fffffffffffffbc5 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000003 R14: 0000000000020000 R15: 0000000000020000
</TASK>
Fix this by validating the PUD entry in walk_pmd_range() using a stable
snapshot (pudp_get()). If the PUD is not present or is a leaf, retry the
walk via ACTION_AGAIN instead of descending further. This mirrors the
retry logic in walk_pte_range(), which lets walk_pmd_range() retry if the
PTE is not being got by pte_offset_map_lock(). |
| Moby is an open source container framework. In Docker Engine prior to version 29.5.1, Docker Daemon versions 28.5.2 and prior, and Moby Daemon prior to version 2.0.0-beta.14, a race condition during docker cp mount setup allows a malicious container to create empty files or directories at arbitrary absolute paths on the host filesystem. This issue has been patched in Docker Engine version 29.5.1 and Moby Daemon version 2.0.0-beta.14. |
| Moby is an open source container framework. In Docker Engine prior to version 29.5.1, Docker Daemon versions 28.5.2 and prior, and Moby Daemon prior to version 2.0.0-beta.14, a race condition during docker cp mount setup allows a malicious container to redirect a bind mount target to an arbitrary host path, potentially overwriting host files or causing denial of service. This issue has been patched in Docker Engine version 29.5.1 and Moby Daemon version 2.0.0-beta.14. |
| Kitty is a cross-platform GPU based terminal. In versions prior to 0.47.2, a local privilege escalation vulnerability exists in kitty's file transmission protocol where a child process running in the terminal can write to arbitrary files on the filesystem by exploiting a TOCTOU (Time-of-Check-Time-of-Use) race condition between symlink validation and file creation. The `os.open()` call used to create files does not use `O_NOFOLLOW`, allowing an attacker to create a symlink between the initial stat check and the actual file open, causing the write to follow the symlink to an arbitrary destination. Version 0.47.2 fixes the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: algif_aead - snapshot IV for async AEAD requests
AF_ALG AEAD AIO requests currently use the socket-wide IV buffer during
request processing. For async requests, later socket activity can
update that shared state before the original request has fully
completed, which can lead to inconsistent IV handling.
Snapshot the IV into per-request storage when preparing the AEAD
request, so in-flight operations no longer depend on mutable socket
state. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: fix deferred split queue races during migration
migrate_folio_move() records the deferred split queue state from src and
replays it on dst. Replaying it after remove_migration_ptes(src, dst, 0)
makes dst visible before it is requeued, so a concurrent rmap-removal path
can mark dst partially mapped and trip the WARN in deferred_split_folio().
Move the requeue before remove_migration_ptes() so dst is back on the
deferred split queue before it becomes visible again.
Because migration still holds dst locked at that point, teach
deferred_split_scan() to requeue a folio when folio_trylock() fails.
Otherwise a fully mapped underused folio can be dequeued by the shrinker
and silently lost from split_queue.
[ziy@nvidia.com: move the comment] |
