| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: aggregator: fix a potential use-after-free
On error we free aggr->lookups->dev_id before removing the entry from
the lookup table. If a concurrent thread calls gpiod_find() before we
remove the entry, it could iterate over the list and call
gpiod_match_lookup_table() which unconditionally dereferences dev_id
when calling strcmp(). Reverse the order of cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: aggregator: remove the software node when deactivating the aggregator
The dynamic software node we create for the aggregator platform device
when using configfs is leaked when the device is deactivated. Destroy it
as the last step in the tear-down path. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/oa: Fix exec_queue leak on width check in stream open
In xe_oa_stream_open_ioctl(), when param.exec_q->width > 1 the
function returns -EOPNOTSUPP directly, skipping the existing
err_exec_q cleanup path. The exec_queue reference obtained by
xe_exec_queue_lookup() is leaked.
The exec queue holds a reference on the xe_file, which is only
dropped during queue teardown. The leaked lookup ref is not on
the file's exec_queue xarray, so file close cannot release it.
This keeps both the exec queue and the file private state pinned
indefinitely.
Jump to err_exec_q instead of returning directly so the reference
is released.
(cherry picked from commit 339fa0be9e4a5d69fa47e91f4a36574224fb478f) |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix durable reconnect error path file lifetime
After a durable reconnect succeeds, ksmbd_reopen_durable_fd() republishes
the same ksmbd_file into the session volatile-id table. If smb2_open()
then takes a later error path, cleanup first calls ksmbd_fd_put(work, fp)
and then unconditionally calls ksmbd_put_durable_fd(dh_info.fp).
In this case fp and dh_info.fp are the same object. The first put drops the
reconnect lookup reference, but the final durable put can run
__ksmbd_close_fd(NULL, fp). Because the final close is not session-aware,
it can free the file object without removing the volatile-id entry that was
just published into the session table.
Use the session-aware put for the final reconnect drop when the reconnect
had already succeeded and the error path is cleaning up the republished
file. Earlier reconnect failures, before fp is assigned to dh_info.fp, keep
using the durable-only put path. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: usbtouchscreen - clamp NEXIO data_len/x_len to URB buffer size
nexio_read_data() pulls data_len and x_len from a packed __be16 header
in the device's interrupt packet and then walks packet->data[0..x_len)
and packet->data[x_len..data_len) comparing each byte against a
threshold.
Both fields are 16-bit on the wire (max 65535). The existing
adjustments shave at most 0x100 / 0x80 off, so the loop bound can still
reach roughly 0xfeff. The URB transfer buffer for NEXIO is rept_size
(1024) bytes from usb_alloc_coherent(), with the first 7 occupied by the
packed header — so packet->data[] has 1017 valid bytes. read_data()
callbacks are not given urb->actual_length, and nothing else bounds the
walk.
A device that lies about its length can get a ~64 KiB out-of-bounds read
past the coherent DMA allocation. The first index whose byte exceeds
NEXIO_THRESHOLD lands in begin_x / begin_y and from there into the
reported touch coordinates, so adjacent kernel memory contents leak to
userspace as ABS_X / ABS_Y events. Far enough out, the read can also
hit an unmapped page and fault.
Fix this all by clamping data_len to the buffer's data[] capacity and
x_len to data_len. |
| In the Linux kernel, the following vulnerability has been resolved:
ethtool: module: avoid leaking a netdev ref on module flash errors
module_flash_fw_schedule() is missing undo for setting
the "in_progress" flag and taking the netdev reference.
Delay taking these, the device can't disappear while
we are holding rtnl_lock. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: Fix use-after-free race in nfc_llcp_recv_cc()
A race condition exists in the NFC LLCP connection state machine where
the connection acceptance packet (CC) can be processed concurrently with
socket release. This can lead to a use-after-free of the socket object.
When nfc_llcp_recv_cc() moves the socket from the connecting_sockets
list to the sockets list, it does so without holding the socket lock.
If llcp_sock_release() is executing concurrently, it might have already
unlinked the socket and dropped its references, which can result in
nfc_llcp_recv_cc() linking a freed socket into the live list.
Fix this by holding lock_sock() during the state transition and list
movement in nfc_llcp_recv_cc(). After acquiring the lock, check if
the socket is still hashed to ensure it hasn't already been unlinked
and marked for destruction by the release path. This aligns the locking
pattern with recv_hdlc() and recv_disc(). |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: Fix use-after-free in llcp_sock_release()
llcp_sock_release() unconditionally unlinks the socket from the local
sockets list. However, if the socket is still in connecting state, it
is on the connecting list.
Fix this by checking the socket state and unlinking from the correct list. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_sfb: Replace direct dequeue call with peek and qdisc_dequeue_peeked
When sfb has children (eg qfq qdisc) whose peek() callback is
qdisc_peek_dequeued(), we could get a kernel panic. When the parent of such
qdiscs (eg illustrated in patch #3 as tbf) wants to retrieve an skb from
its child (sfb in this case), it will do the following:
1a. do a peek() - and when sensing there's an skb the child can offer, then
- the child in this case(sfb) calls its child's (qfq) peek.
qfq does the right thing and will return the gso_skb queue packet.
Note: if there wasnt a gso_skb entry then qfq will store it there.
1b. invoke a dequeue() on the child (sfb). And herein lies the problem.
- sfb will call the child's dequeue() which will essentially just
try to grab something of qfq's queue.
[ 127.594489][ T453] KASAN: null-ptr-deref in range [0x0000000000000048-0x000000000000004f]
[ 127.594741][ T453] CPU: 2 UID: 0 PID: 453 Comm: ping Not tainted 7.1.0-rc1-00035-gac961974495b-dirty #793 PREEMPT(full)
[ 127.595059][ T453] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 127.595254][ T453] RIP: 0010:qfq_dequeue+0x35c/0x1650 [sch_qfq]
[ 127.595461][ T453] Code: 00 fc ff df 80 3c 02 00 0f 85 17 0e 00 00 4c 8d 73 48 48 89 9d b8 02 00 00 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 ea 03 <80> 3c 02 00 0f 85 76 0c 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8b
[ 127.596081][ T453] RSP: 0018:ffff88810e5af440 EFLAGS: 00010216
[ 127.596337][ T453] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: dffffc0000000000
[ 127.596623][ T453] RDX: 0000000000000009 RSI: 0000001880000000 RDI: ffff888104fd82b0
[ 127.596917][ T453] RBP: ffff888104fd8000 R08: ffff888104fd8280 R09: 1ffff110211893a3
[ 127.597165][ T453] R10: 1ffff110211893a6 R11: 1ffff110211893a7 R12: 0000001880000000
[ 127.597404][ T453] R13: ffff888104fd82b8 R14: 0000000000000048 R15: 0000000040000000
[ 127.597644][ T453] FS: 00007fc380cbfc40(0000) GS:ffff88816f2a8000(0000) knlGS:0000000000000000
[ 127.597956][ T453] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 127.598160][ T453] CR2: 00005610aa9890a8 CR3: 000000010369e000 CR4: 0000000000750ef0
[ 127.598390][ T453] PKRU: 55555554
[ 127.598509][ T453] Call Trace:
[ 127.598629][ T453] <TASK>
[ 127.598718][ T453] ? mark_held_locks+0x40/0x70
[ 127.598890][ T453] ? srso_alias_return_thunk+0x5/0xfbef5
[ 127.599053][ T453] sfb_dequeue+0x88/0x4d0
[ 127.599174][ T453] ? ktime_get+0x137/0x230
[ 127.599328][ T453] ? srso_alias_return_thunk+0x5/0xfbef5
[ 127.599480][ T453] ? qdisc_peek_dequeued+0x7b/0x350 [sch_qfq]
[ 127.599670][ T453] ? srso_alias_return_thunk+0x5/0xfbef5
[ 127.599831][ T453] tbf_dequeue+0x6b1/0x1098 [sch_tbf]
[ 127.599988][ T453] __qdisc_run+0x169/0x1900
The right thing to do in #1b is to grab the skb off gso_skb queue.
This patchset fixes that issue by changing #1b to use qdisc_dequeue_peeked()
method instead. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel/pt: Fix stop/start with no update
If pt_event_stop() is called without PERF_EF_UPDATE flag, then
perf_aux_output_end() is not called. A subsequent call to pt_event_start()
will call perf_aux_output_begin() again which violates the rule against
nesting and triggers a WARNING in perf_aux_output_begin().
Originally, pt_event_stop() was never called without PERF_EF_UPDATE,
because the only code paths to do so are from event overflow, and Intel PT
does not do that.
However the introduction of group throttling by commit 9734e25fbf5ae
("perf: Fix the throttle logic for a group") meant that an Intel PT event
could be throttled if it was part of a group. Throttling calls PMU
->stop() / ->start() callbacks without flags.
An example is when AUX area sampling is used. The following commands
hit the issue:
echo 10000 > /proc/sys/kernel/perf_event_max_sample_rate
perf record -F32000 --aux-sample -e '{intel_pt//u,cycles:u}' \
-- bash -c 'for i in `seq 1 100000` ; do true ; done'
Use PERF_HES_UPTODATE to track whether perf_aux_output_begin() and
perf_aux_output_end() are balanced. A cleared PERF_HES_UPTODATE bit
indicates that an AUX output context is still open.
Amend pt_event_start() / pt_event_stop() accordingly so that begin/end
stay balanced:
- In non-snapshot mode, stop() always closes the buffer (the buffer may
have run out of space, and that accounting is done by the update), so
a following start() opens a fresh one as before.
- In snapshot/overwrite mode, stop() without PERF_EF_UPDATE leaves the
buffer open so that pt_event_snapshot_aux() can still copy from it,
and start() then only re-enables tracing instead of calling
perf_aux_output_begin() again.
Note that pt_event_del() calls pt_event_stop() with PERF_EF_UPDATE flag set
(as is required by the documentation), so a final call to
perf_aux_output_end() is assured. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: hibernate: pass HVC_SET_VECTORS args to the resume hvc
swsusp_arch_suspend_exit() reinstalls the restored kernel's hyp stub
vectors with an hvc, but never passes the arguments. x0 is not set to
HVC_SET_VECTORS and x1 is not set to the vector address, so the stub
dispatch falls through and returns without writing vbar_el2. EL2 is
left pointing at the trans_pgd copy of the vectors, a page that
swsusp_free() releases right after resume.
Set the arguments up the same way __hyp_set_vectors() does.
Without this fix, Vladimir was able to trigger a hang when resuming from
hibernation with CONFIG_PAGE_POISONING=y and page_poison=on. |
| In the Linux kernel, the following vulnerability has been resolved:
seg6: set IPSKB_L3SLAVE from IP6SKB_L3SLAVE on IPIP decapsulation
When an SRv6 packet arrives on an interface enslaved to a VRF,
vrf_ip6_rcv() sets IP6SKB_L3SLAVE in IP6CB, but decap_and_validate()
has never set IPSKB_L3SLAVE in IPCB. The bit stayed clear in the
common case, and with CONFIG_IPV6_MIP6 the leftover frag_max_size of
a reassembled outer packet could even set it, with no VRF involved.
Commit 44930446dde4 ("ipv6: seg6: clear IPv4 control block on IPIP
decapsulation") then made the unreliable bit reliably clear.
The effect of the missing flag is visible with End.DX4 when a
delivery to a local address of the node reaches the socket lookup.
For example, a UDP socket bound to the enslaved ingress interface
does not receive any of the decapsulated packets, while an unbound
socket outside the VRF does.
This contradicts Documentation/networking/vrf.rst: by default the
scope of an unbound UDP or TCP socket is limited to the default VRF.
Set IPSKB_L3SLAVE for IPv4 in decap_and_validate(), which already does
the same for IPv6. The socket lookup then matches the decapsulated
packet like any other packet received on that enslaved interface. Such
a packet matches an unbound UDP or TCP socket only when
udp_l3mdev_accept or tcp_l3mdev_accept is set. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: cleanup arsta in ath11k_mac_peer_cleanup_all()
When mac80211 removes a sta, it calls .sta_state() which in turn calls
ath11k_mac_station_remove(). In that function we clean up both peers &
arsta related resources.
But when the firmware crashes, ath11k calls ieee80211_restart_hw(), which
assumes that all driver related resources are cleaned up beforehand. This
cleanup is supposedly done by ath11k_mac_peer_cleanup_all() but does not
in fact free arsta->rx_stats / tx_stats.
Extract the arsta cleanup from ath11k_mac_station_remove() into a
new ath11k_mac_station_cleanup() and call it from both there and
ath11k_mac_peer_cleanup_all().
This should handle kmemleaks reports like:
unreferenced object 0xffffff801ae66400 (size 1024):
comm "hostapd", pid 1306, jiffies 4295011565
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc d61c08ec):
kmemleak_alloc+0x3c/0x50
__kmalloc_cache_noprof+0x2b0/0x3e0
ath11k_mac_op_sta_state+0x1dc/0xb10
drv_sta_state+0xac/0x6f8
sta_info_insert_rcu+0x314/0x5e0
sta_info_insert+0x14/0x38
ieee80211_add_station+0x10c/0x1a0
nl80211_new_station+0x3e8/0x680
genl_family_rcv_msg_doit+0xc0/0x120
genl_rcv_msg+0x1b4/0x258
netlink_rcv_skb+0x4c/0x108
genl_rcv+0x38/0x60
netlink_unicast+0x190/0x278
netlink_sendmsg+0x15c/0x370
____sys_sendmsg+0x120/0x290
___sys_sendmsg+0x70/0xa0
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.9.0.1-01977-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: clear free space tree creation state on rebuild failure
btrfs_rebuild_free_space_tree() sets BTRFS_FS_CREATING_FREE_SPACE_TREE
before rebuilding the free space tree. Several error paths return
without clearing this flag.
The transaction restart failure path can leave the flag set on a live
filesystem, causing delayed reference processing to be skipped. Clear it
on all free space tree rebuild failure paths. Keep
BTRFS_FS_FREE_SPACE_TREE_UNTRUSTED set, since a failed rebuild leaves
the free space tree untrusted. Callers must fall back to extent-tree
caching. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: percpu: Fix LSE operations on {8,16}-bit types
The assembly for __percpu_##name##_case_##sz() and
__percpu_##name##_return_case_##sz() doesn't use the 'sfx' macro
argument to form the LSE instruction. Without 'sfx', a W register
argument will imply a 32-bit memory location, and consequently
{8,16}-bit ops will erroneously read and write 32 bits of memory when
the LSE instruction is used.
Fix this by appending 'sfx' to 'op_lse' to LSE instruction. It is not
necessary (and not valid) to append 'sfx' to 'op_llsc', as 'op_llsc' is
a register-register operation which does not access memory (and does not
take a size suffix). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Fix parent socket leak in iso_conn_ready()
iso_get_sock() returns the parent socket with a reference held, which is
dropped by sock_put() once the child socket has been set up. The error
path taken when iso_sock_alloc() fails only calls release_sock() and
returns, leaking the reference and thus the parent socket itself.
Drop the reference on that path as well. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel_pcie: validate TX skb length in send_sync
btintel_pcie_prepare_tx() copies skb->len bytes into a fixed
BTINTEL_PCIE_BUFFER_SIZE (4096) DMA slot via an unchecked memcpy.
Oversized packets are currently rejected only in
btintel_pcie_send_frame(); any future caller of
btintel_pcie_send_sync() would silently overflow the DMA buffer.
Add the bounds check in btintel_pcie_send_sync() itself, right
before skb_push() and the DMA copy. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: Don't call skb_clone_and_charge_r() for close()d listener in tcp_v6_do_rcv().
tcp_v6_do_rcv() no longer calls skb_clone_and_charge_r() for
TCP_LISTEN since commit 073d89808c06 ("net: fix data-races around
sk->sk_forward_alloc").
However, there is still a small race window between tcp_v6_rcv()
and tcp_v6_do_rcv(), where concurrent close() changes TCP_LISTEN
to TCP_CLOSE, causing skb_clone_and_charge_r() to be called
locklessly and resulting in the splat below. [0]
Let's avoid calling skb_clone_and_charge_r() for TCP_CLOSE as well.
This is fine for non-listeners because tcp_rcv_state_process()
drops skb for TCP_CLOSE and opt_skb was freed immediately anyway.
[0]:
sk->sk_forward_alloc
WARNING: net/ipv4/af_inet.c:162 at inet_sock_destruct+0x64d/0x810 net/ipv4/af_inet.c:162, CPU#1: ksoftirqd/1/28
Modules linked in:
CPU: 1 UID: 0 PID: 28 Comm: ksoftirqd/1 Not tainted 7.2.0 #17 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-debian-1.17.0-1 04/01/2014
RIP: 0010:inet_sock_destruct+0x64d/0x810 net/ipv4/af_inet.c:162
Code: 3d 49 ff e9 06 fd ff ff e8 d0 5b 83 f8 90 0f 0b 90 e9 35 fe ff ff e8 c2 5b 83 f8 90 0f 0b 90 e9 c5 fe ff ff e8 b4 5b 83 f8 90 <0f> 0b 90 e9 04 ff ff ff e8 a6 5b 83 f8 90 0f 0b 90 e9 65 fe ff ff
RSP: 0018:ffffc90000677bb8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8880117bde80 RCX: ffffffff8957eb41
RDX: ffff88801dad5d00 RSI: ffffffff8957ec3c RDI: 0000000000000005
RBP: 00000000fffff000 R08: ffffffff8957eb41 R09: 00000000fffff000
R10: 0000000000000005 R11: 0000000000000000 R12: dffffc0000000000
R13: ffff8880117bdf10 R14: ffffffff81c08eb7 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff8880d7ae5000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f93a1021138 CR3: 00000000207a9000 CR4: 0000000000350ef0
Call Trace:
<TASK>
__sk_destruct+0x82/0xae0 net/core/sock.c:2356
rcu_do_batch kernel/rcu/tree.c:2645 [inline]
rcu_core+0x59c/0x1100 kernel/rcu/tree.c:2897
handle_softirqs+0x1e4/0x9b0 kernel/softirq.c:622
run_ksoftirqd kernel/softirq.c:1076 [inline]
run_ksoftirqd+0x38/0x60 kernel/softirq.c:1068
smpboot_thread_fn+0x458/0xc80 kernel/smpboot.c:160
kthread+0x396/0x4a0 kernel/kthread.c:436
ret_from_fork+0x8e0/0xe40 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: mst: move switchdev call outside rcu
This is a follow-up of one of sashiko's pre-existing bug reports.
br_mst_set_state() calls switchdev_port_attr_set() for nonzero MSTIs
while holding rcu_read_lock() which invokes the blocking switchdev
notifier chain and may sleep. Nonzero MSTI changes come from netlink
with rtnl held. Move the switchdev call before entering the rcu section and
assert that rtnl is held.
The call cannot be deferred because netlink needs its error and extack.
Also DSA reads the old bridge MST state during the callback and checks it.
A deferred callback will be late and will see the updated state. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: mxl862xx: disable the stats poll on teardown
mxl862xx_setup() arms the stats poll before mxl862xx_setup_mdio(), and
nothing stops it until dsa_register_switch() has returned an error to
mxl862xx_probe(). DSA frees the dsa_port list before it returns, so a
poll that fires once .setup or a later step of dsa_tree_setup() has
failed walks freed ports. On shutdown the user ports stay registered,
and the WORK_STOPPED flag test in mxl862xx_get_stats64() is not atomic
with the cancel in mxl862xx_shutdown(), so a re-arm that read the flag
before it was set queues the poll after cancel_delayed_work_sync() has
returned.
Arm the poll once .setup has succeeded and stop it from a .teardown op,
which DSA calls on unregister and after a failed registration, in both
cases before it frees the ports. Use disable_delayed_work_sync() there
and in shutdown(): it drains a running poll as the cancel did and turns
every later attempt to queue the work into a no-op, so the re-arm
cannot bring the poll back. remove() and the probe error path only set
WORK_STOPPED, which crc_err_work tests before it walks the ports. |
