| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/msm: Unwind probe state on registration failure
msm_iommu_probe() adds its devm-managed IOMMU object to
qcom_iommu_devices before adding the IOMMU sysfs device and registering
it with the IOMMU core.
If iommu_device_sysfs_add() fails, probe returns with the object still on
qcom_iommu_devices. The driver core then releases the devm allocation,
leaving a dangling list entry that later list walks may dereference.
If iommu_device_register() fails, the same dangling list entry remains
and the sysfs device is left registered as well.
Unwind the sysfs device and global list entry in reverse setup order on
the corresponding failure paths. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: via-sdmmc: cancel card-detect work on remove
Disabling the device interrupt and freeing the IRQ prevents new card-detect
work from being queued, but carddet_work already queued by the handler can
still run after via_sd_remove() returns. via_sdc_card_detect() recovers the
host through container_of() and dereferences its MMIO base; once remove()
returns the host can be freed, so that work would touch freed memory.
Cancel carddet_work after freeing the IRQ and before cancelling
finish_bh_work, which the card-detect handler can also queue. carddet_work
can re-enable the interrupt through via_reset_pcictrl(); mask it again
afterwards.
This issue was found by an in-house static analysis tool and confirmed by
manual code review. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86/amd/pmc: Propagate SMU errors and validate S2D address
amd_stb_s2d_init() discards the return value of several S2D SMU commands.
When the SMU refuses a command (e.g. "SMU cmd failed. err: 0xff") the
failure is only noticed indirectly - if at all - and reported as -EIO,
masking the real error.
More seriously, the S2D_PHYS_ADDR_LOW/HIGH return values are ignored, so
on failure phys_addr_low/hi are left uninitialised and the assembled
address is passed straight to devm_ioremap(). When the SMU leaves them at
zero this maps physical address 0 and trips the ioremap-on-RAM warning:
amd_pmc AMDI000B:00: SMU cmd failed. err: 0xff
ioremap on RAM at 0x0000000000000000 - 0x0000000000ffffff
WARNING: CPU: 13 PID: 4592 at arch/x86/mm/ioremap.c:...
Check the return value of each SMU command and propagate it, and reject a
zero physical address before calling devm_ioremap(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: ravb: serialize PTP clock teardown
ravb_ptp_interrupt() can race with ravb_ptp_stop() and pass the clock to
ptp_clock_event() while ptp_clock_unregister() is freeing it. This can
lead to a use-after-free.
Use READ_ONCE() and WRITE_ONCE() for lockless access to the clock pointer.
Atomically detach it with xchg() before disabling PTP interrupts, then
synchronize all IRQs which can invoke ravb_ptp_interrupt() before
unregistering the detached clock.
A handler which read the old pointer completes before the clock is
unregistered, while later handlers read NULL and skip the event. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl8xxxu: fix use-after-free from rx_urb_wq on stop
rtl8xxxu arms rx_urb_wq from the RX completion path:
rtl8xxxu_rx_complete() hands the URB to rtl8xxxu_queue_rx_urb(), which
queues it on rx_urb_pending_list and, once the list grows past
RTL8XXXU_RX_URB_PENDING_WATER, schedules rx_urb_wq. The worker
rtl8xxxu_rx_urb_work() drains rx_urb_pending_list, recovers priv through
container_of, and resubmits each URB through rtl8xxxu_submit_rx_urb(),
which anchors it on rx_anchor and dereferences priv->udev.
rtl8xxxu_stop() cancels the sibling work items (c2hcmd_work, ra_watchdog,
update_beacon_work) but never cancels rx_urb_wq, so a worker armed during
the last burst of RX traffic can run rtl8xxxu_rx_urb_work() after
rtl8xxxu_disconnect() has called ieee80211_free_hw(), which frees priv,
producing a use-after-free. The window opens under active RX traffic
(pending count above the watermark) followed by a disconnect.
There are two teardown races to close:
* rtl8xxxu_queue_rx_urb() decided whether to enqueue under rx_urb_lock
but called schedule_work() after dropping the lock. A completion
that observed shutdown == false and released the lock could then call
schedule_work() after rtl8xxxu_stop() had set shutdown and
cancel_work_sync() had already returned, arming the worker to run
after the teardown. Move schedule_work() under the same !shutdown
branch so the arming decision is atomic with the shutdown check.
* rtl8xxxu_rx_urb_work() anchors every URB it drained back onto
rx_anchor through rtl8xxxu_submit_rx_urb(). A worker still running
when usb_kill_anchored_urbs(&priv->rx_anchor) returned would submit a
URB that escaped the kill. In rtl8xxxu_stop(), call
cancel_work_sync(&priv->rx_urb_wq) before the kill so the worker is
drained first.
After priv->shutdown is set under rx_urb_lock, completions can no longer
queue rx_urb_wq. cancel_work_sync() then drains the last queued or running
worker, and the following usb_kill_anchored_urbs() kills the URBs it may
have submitted.
rtl8xxxu_disconnect() is covered because ieee80211_unregister_hw()
guarantees .stop() runs for a live interface before ieee80211_free_hw()
frees priv. The probe error path needs no cancel: rx_urb_wq is
INIT_WORK()'d there but cannot have been scheduled, since no URB is
submitted before ieee80211_register_hw() succeeds.
This bug was found by static analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: bound the device EEPROM address before the EFUSE copy
mt7915_mcu_get_eeprom() copies a fixed EFUSE block into the driver's
dev->mt76.eeprom.data buffer at the offset reported by the MCU response
(res->addr, a device-controlled __le32) without checking it against the
buffer size. A malicious or malfunctioning device can report an arbitrary
address and drive a 16-byte out-of-bounds write past eeprom.data.
Reject a response whose address would place the copy outside eeprom.data
before deriving the destination pointer. Devices that echo the requested
in-bounds offset are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: bound the device EEPROM address before the EFUSE copy
mt7996_mcu_get_eeprom() derives the destination of the EFUSE/EXT block
copy from the address reported by the MCU response (event->addr, a
device-controlled __le32) and clamps only the copy length, never the
destination offset into dev->mt76.eeprom.data. A malicious or
malfunctioning device can report an arbitrary address and drive an
out-of-bounds write of up to MT7996_EXT_EEPROM_BLOCK_SIZE bytes past
eeprom.data.
Reject a response whose address would place the copy outside eeprom.data
before deriving the destination pointer. Devices that echo the requested
in-bounds offset are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Add bounds check for CRAT subtype length
The CRAT parser validates that the subtype header fits within the image,
but does not verify that the advertised subtype length fits. A malformed
CRAT table with an oversized length field causes out-of-bounds reads when
kfd_parse_subtype() casts the header to specific subtype structures.
Add validation that sub_type_hdr + length does not exceed the image
boundary before parsing the subtype contents.
(cherry picked from commit 48e1d1e6e8798aef0312e68d8e586021b5b3cf4d) |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Check sk_state before sk_protocol in bpf_tcp_*_syncookie
bpf_tcp_gen_syncookie and bpf_tcp_check_syncookie accept a socket pointer
'sk' with argument type ARG_PTR_TO_BTF_ID_SOCK_COMMON. However, they access
sk->sk_protocol without validating whether 'sk' represents a full socket.
Fix this issue by checking sk->sk_state != TCP_LISTEN before inspecting
sk->sk_protocol in both bpf_tcp_gen_syncookie and bpf_tcp_check_syncookie.
Since mini-sockets are never in the TCP_LISTEN state, the condition
short-circuits and prevents dereferencing fullsock-specific fields. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: initialize inode mapping flags for cached inodes
[BUG]
When running generic/795 with 8K block size, 4K page size, the test
always fails, triggering some ASSERT()s related to folio size:
795 (241074): drop_caches: 3
assertion failed: IS_ALIGNED(start, blocksize) && IS_ALIGNED(end + 1, blocksize), in extent_io.c:1404 (blocksize=8192 root=262 ino=258 start=16826368 end=16830463 mapping min order=0)
------------[ cut here ]------------
kernel BUG at extent_io.c:1404!
Oops: invalid opcode: 0000 [#1] SMP
CPU: 8 UID: 0 PID: 241105 Comm: fsstress Tainted: G OE 7.2.0-rc5-custom+ #442 PREEMPT(full) f4bfb352566f3949f29c233ce6f735050a03b245
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022
RIP: 0010:assert_folio_range.cold+0x3d/0x3f [btrfs]
Call Trace:
<TASK>
btrfs_read_folio+0x9e/0x170 [btrfs 4cd1dd93b341b8ef766643f9512f4a86259567a3]
prepare_one_folio.constprop.0+0x104/0x2a0 [btrfs 4cd1dd93b341b8ef766643f9512f4a86259567a3]
btrfs_buffered_write+0x285/0xa50 [btrfs 4cd1dd93b341b8ef766643f9512f4a86259567a3]
btrfs_do_write_iter+0x1aa/0x210 [btrfs 4cd1dd93b341b8ef766643f9512f4a86259567a3]
iter_file_splice_write+0x31a/0x540
direct_splice_actor+0x53/0x170
splice_direct_to_actor+0xe9/0x240
do_splice_direct+0x76/0xb0
vfs_copy_file_range+0x1fd/0x630
__x64_sys_copy_file_range+0xf9/0x220
do_syscall_64+0xe1/0x790
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
The ASSERT() itself is added by a later patch.
The crash is triggered with that new debug patch, and without this fix.
[CAUSE]
In the above case, the start 16826368 is properly 8K aligned, but the
end (16830463 + 1) is not 8K aligned.
Furthermore the mapping's minimal folio order is 0, not the expected 1
for 8K block size with 4K page size.
So this means some inodes do not have btrfs_set_inode_mapping_order()
called on it.
The missing btrfs_set_inode_mapping_order() call happens for cached
inodes, through the following events:
- btrfs_create_new_inode() called for inode X
Which properly sets minimal folio order for the VFS inode.
- btrfs_update_inode() called for inode X
Which calls btrfs_delayed_update_inode() to create a delayed_node
into root->delayed_nodes xarray.
- Drop cache/memory pressure, evicting in-memory inode X
Which evicted the inode X, but delayed_node is still in
root->delayed_nodes for future reuse.
- btrfs_iget() for inode X called again
btrfs_iget()
|- btrfs_iget_locked()
| |- iget5_locked_rcu()
| Which creates a new vfs_inode for btrfs, whose mapping still
| has the minimal order as 0.
|
|- btrfs_read_locked_inode()
|- btrfs_fill_inode()
| |- btrfs_get_delayed_node()
| Which found out the previous node, and use that delayed
| node to initialize the new inode.
|
|- filled = true;
|- if (filled) goto cache_index;
Which skips the btrfs_update_inode_mapping_flags() and
btrfs_set_inode_mapping_order() calls.
So the inode still has minimal folio order set as 0, not
the required 1.
Thus later page cache read will get a folio whose size is smaller than
block size, as the mapping has its minimal folio order set as 0 not 1,
then trigger the ASSERT().
[FIX]
Move the btrfs_update_inode_mapping_flags() and
btrfs_set_inode_mapping_order() calls under cache_index label,
so that the mapping flags and minimal folio order is always set
no matter if we have a cached inode. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: fix double free of wq, engine, and group structs
The release callbacks for wq, engine, and group devices
(idxd_conf_wq_release, idxd_conf_engine_release,
idxd_conf_group_release) each call kfree() on the enclosing struct.
The setup error paths and cleanup functions also call kfree()
explicitly after put_device(), producing a double free whenever
put_device() drops the reference count to zero and fires the release.
In the setup functions, device_initialize() is called before
device_add(), so the reference count is exactly 1 at the error sites.
put_device() unconditionally fires the release, which frees the struct;
the subsequent explicit kfree() then operates on freed memory.
For idxd_setup_wqs(), the wq release callback also owns opcap_bmap
and wqcfg. The error unwind additionally freed those fields explicitly
before calling put_device(), causing further double frees on both.
Remove the redundant explicit kfree() calls from all setup error paths
and cleanup functions for wq, engine, and group structs, delegating
sole ownership of those allocations to the release callbacks. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: hold conn in hci_connect_acl/le_sync() callbacks
There is theoretical UAF if the conn is freed while the hci_sync task
is running.
Hold refcount to avoid that. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl: Fix CXL_HEADERLOG_SIZE to match RAS Capability size
The CXL r4.0 8.2.4.17.7 RAS Capability Structure has total length 0x58
bytes (CXL_RAS_CAPABILITY_LENGTH); the Header Log occupies the trailing
64 bytes at offset 0x18. CXL_HEADERLOG_SIZE was defined as SZ_512,
eight times the actual on-device size.
header_log_copy() reads CXL_HEADERLOG_SIZE_U32 (128) dwords from the
RAS capability iomap, overrunning the 88-byte mapping by 448 bytes.
The cxl_aer_uncorrectable_error trace event memcpy()s CXL_HEADERLOG_SIZE
(512) bytes from its source. For the CPER caller the source is
struct cxl_ras_capability_regs::header_log[16] (64 bytes) embedded in a
stack-local cxl_cper_prot_err_work_data, so the memcpy reads 448 bytes
of kernel stack into the trace event ring buffer where userspace can
read it via tracefs.
Set CXL_HEADERLOG_SIZE to 64 and derive CXL_HEADERLOG_SIZE_U32 from it,
bringing all iomap readers into agreement on 16 dwords. Userspace tools
such as rasdaemon have grown a dependency on the buggy 512-byte (128 u32)
header_log layout in the cxl_aer_uncorrectable_error trace event. Add
CXL_HEADERLOG_TRACE_SIZE_U32 = 128 and use it for the trace event
__array and its memcpy to preserve that ABI. Both callers now pass a
zero-filled u32[CXL_HEADERLOG_TRACE_SIZE_U32] staging buffer with only
the first CXL_HEADERLOG_SIZE_U32 (16) entries populated from hardware;
the remaining 112 u32s are zero-padded, keeping the 512-byte trace ring
buffer layout intact.
[ dj: Replaced 64 with SZ_64 per RichardC ] |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: hisi_sas: Add slave_destroy interface for v3 hw
WARNING is triggered when executing link reset of remote PHY and rmmod
SAS driver simultaneously. Following is the WARNING log:
WARNING: CPU: 61 PID: 21818 at drivers/base/core.c:1347 __device_links_no_driver+0xb4/0xc0
Call trace:
__device_links_no_driver+0xb4/0xc0
device_links_driver_cleanup+0xb0/0xfc
__device_release_driver+0x198/0x23c
device_release_driver+0x38/0x50
bus_remove_device+0x130/0x140
device_del+0x184/0x434
__scsi_remove_device+0x118/0x150
scsi_remove_target+0x1bc/0x240
sas_rphy_remove+0x90/0x94
sas_rphy_delete+0x24/0x3c
sas_destruct_devices+0x64/0xa0 [libsas]
sas_revalidate_domain+0xe4/0x150 [libsas]
process_one_work+0x1e0/0x46c
worker_thread+0x15c/0x464
kthread+0x160/0x170
ret_from_fork+0x10/0x20
---[ end trace 71e059eb58f85d4a ]---
During SAS phy up, link->status is set to DL_STATE_AVAILABLE in
device_links_driver_bound, then this setting influences
__device_links_no_driver() before driver rmmod and caused WARNING.
Add the slave_destroy interface to make sure link is removed after flush
workque. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: synproxy: fix unaligned memory access in timestamp adjustment
Use get_unaligned_be32() and put_unaligned_be32() to safely read and
write the timestamp fields. This prevents performance degradation due to
unaligned memory access or even a crash on strict alignment
architectures.
This follows the implementation of timestamp parsing in the networking
stack at tcp_parse_options() and synproxy_parse_options(). |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: lzo: reject compressed segment that overflows the compressed input
lzo_decompress_bio() validates each on-disk segment length seg_len only
against the workspace cbuf size, not against the compressed input size
(compressed_len, the total folio bytes of the bio). A crafted extent can
carry a segment whose seg_len passes the cbuf check but runs past the end
of the bio, so copy_compressed_segment() walks off the last folio:
get_current_folio() then returns the NULL folio from bio_next_folio(), and
with CONFIG_BTRFS_ASSERT disabled (default) folio_size(NULL) faults.
BUG: KASAN: null-ptr-deref in lzo_decompress_bio (fs/btrfs/lzo.c:383)
Read of size 8 at addr 0000000000000000 by task kworker/u8:1/29
Workqueue: btrfs-endio simple_end_io_work
kasan_report (mm/kasan/report.c:590)
lzo_decompress_bio (fs/btrfs/lzo.c:383)
end_bbio_compressed_read (fs/btrfs/compression.c:1065)
btrfs_bio_end_io (fs/btrfs/bio.c:135)
btrfs_check_read_bio (fs/btrfs/bio.c:180 fs/btrfs/bio.c:285)
simple_end_io_work
process_one_work
worker_thread
Reject any segment whose payload would extend beyond compressed_len before
copying it, treating it as corruption like the other on-disk validation
failures in this function. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: oss: Serialize readq reset state with q->lock
snd_seq_oss_readq_clear() resets qlen, head, and tail without
q->lock even though the normal reader and producer paths serialize the
same ring state under that spinlock. A reset can therefore race
snd_seq_oss_readq_free() or snd_seq_oss_readq_put_event() and leave
stale records in the queue, drop freshly queued ones, or report the
wrong readiness after wakeup. KCSAN reports a data race between
snd_seq_oss_readq_clear() and snd_seq_oss_readq_free().
Take q->lock while clearing the ring and resetting input_time. Factor
the enqueue logic into a caller-locked helper so
snd_seq_oss_readq_put_timestamp() updates its suppression state under
the same lock instead of racing the reset path.
The buggy scenario involves two paths, with each column showing the
order within that path:
reset path: locked readq updater:
1. snd_seq_oss_reset() or 1. A reader or callback producer
release reaches takes q->lock on the same queue.
snd_seq_oss_readq_clear().
2. snd_seq_oss_readq_clear() 2. The updater tests or modifies
resets qlen, head, tail, qlen, head, and tail.
and input_time.
3. snd_seq_oss_readq_clear() 3. The updater completes its
wakes sleepers on read-modify-write sequence.
q->midi_sleep.
4. Without q->lock, the reset 4. The resulting ring state drives
can overlap the locked later reads and readiness.
update.
KCSAN reports:
BUG: KCSAN: data-race in snd_seq_oss_readq_clear /
snd_seq_oss_readq_free
write to 0xffff8881069fe608 of 4 bytes by task 120516 on cpu 0:
snd_seq_oss_readq_free+0x6c/0x80
snd_seq_oss_read+0xcb/0x250
odev_read+0x38/0x60
vfs_read+0xff/0x600
ksys_read+0xb4/0x140
__x64_sys_read+0x46/0x60
do_syscall_64+0xbb/0x2f0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
read to 0xffff8881069fe608 of 4 bytes by task 120517 on cpu 1:
snd_seq_oss_readq_clear+0x1f/0x90
snd_seq_oss_reset+0xa7/0xf0
snd_seq_oss_ioctl+0x6f6/0x7e0
odev_ioctl+0x56/0xc0
__x64_sys_ioctl+0xd1/0x120
do_syscall_64+0xbb/0x2f0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
value changed: 0x00000001 -> 0x00000000 |
| In the Linux kernel, the following vulnerability has been resolved:
media: chips-media: wave5: Fix Null reference while testing fluster
When multi instances are created/destroyed, many interrupts happens
and structures for decoder are removed.
"struct vpu_instance" this structure is shared for all flow in the decoder,
so if the structure is not protected by lock, Null dereference
could happens sometimes.
IRQ Handler was spilt to two phases and Lock was added as well. |
| In the Linux kernel, the following vulnerability has been resolved:
alpha: fix user-space corruption during memory compaction
Alpha systems can suffer sporadic user-space crashes and heap
corruption when memory compaction is enabled.
Symptoms include SIGSEGV, glibc allocator failures (e.g. "unaligned
tcache chunk"), and compiler internal errors. The failures disappear
when compaction is disabled or when using global TLB invalidation.
The root cause is insufficient TLB shootdown during page migration.
Alpha relies on ASN-based MM context rollover for instruction cache
coherency, but this alone is not sufficient to prevent stale data or
instruction translations from surviving migration.
Fix this by introducing a migration-specific helper that combines:
- MM context invalidation (ASN rollover),
- immediate per-CPU TLB invalidation (TBI),
- synchronous cross-CPU shootdown when required.
The helper is used only by migration/compaction paths to avoid changing
global TLB semantics.
Additionally, update flush_tlb_other(), pte_clear(), to use
READ_ONCE()/WRITE_ONCE() for correct SMP memory ordering.
This fixes observed crashes on both UP and SMP Alpha systems. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: chipidea: udc: fix DMA and SG cleanup in _ep_nuke()
The ChipIdea UDC driver can encounter "not page aligned sg buffer"
errors when a USB device is reconnected after being disconnected
during an active transfer. This occurs because _ep_nuke() returns
requests to the gadget layer without properly unmapping DMA buffers
or cleaning up scatter-gather bounce buffers.
Root cause:
When a disconnect happens during a multi-segment DMA transfer, the
request's num_mapped_sgs field and sgt.sgl pointer remain set with
stale values. The request is returned to the gadget driver with status
-ESHUTDOWN but still has active DMA state. If the gadget driver reuses
this request on reconnect without reinitializing it, the stale DMA
state causes _hardware_enqueue() to skip DMA mapping (seeing non-zero
num_mapped_sgs) and attempt to use freed/invalid DMA addresses,
leading to alignment errors and potential memory corruption.
The normal completion path via _hardware_dequeue() properly calls
usb_gadget_unmap_request_by_dev() and sglist_do_debounce() before
returning the request. The _ep_nuke() path must do the same cleanup
to ensure requests are returned in a clean, reusable state.
Fix:
Add DMA unmapping and bounce buffer cleanup to _ep_nuke() to mirror
the cleanup sequence in _hardware_dequeue():
- Call usb_gadget_unmap_request_by_dev() if num_mapped_sgs is set
- Call sglist_do_debounce() with copy=false if bounce buffer exists
This ensures that when requests are returned due to endpoint shutdown,
they don't retain stale DMA mappings. The 'false' parameter to
sglist_do_debounce() prevents copying data back (appropriate for
shutdown path where transfer was aborted). |
