| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Reject non-8-byte ATOMIC_WRITE payloads
atomic_write_reply() at drivers/infiniband/sw/rxe/rxe_resp.c
unconditionally dereferences 8 bytes at payload_addr(pkt):
value = *(u64 *)payload_addr(pkt);
check_rkey() previously accepted an ATOMIC_WRITE request with pktlen ==
resid == 0 because the length validation only compared pktlen against
resid. A remote initiator that sets the RETH length to 0 therefore reaches
atomic_write_reply() with a zero-byte logical payload, and the responder
reads sizeof(u64) bytes from past the logical end of the packet into
skb->head tailroom, then writes those 8 bytes into the attacker's MR via
rxe_mr_do_atomic_write(). That is a remote disclosure of 4 bytes of kernel
tailroom per probe (the other 4 bytes are the packet's own trailing ICRC).
IBA oA19-28 defines ATOMIC_WRITE as exactly 8 bytes. Anything else is
protocol-invalid. Hoist a strict length check into check_rkey() so the
responder never reaches the unchecked dereference, and keep the existing
WRITE-family length logic for the normal RDMA WRITE path.
Reproduced on mainline with an unmodified rxe driver: a sustained
zero-length ATOMIC_WRITE probe repeatedly leaks adjacent skb head-buffer
bytes into the attacker's MR, including recognisable kernel strings and
partial kernel-direct-map pointer words. With this patch applied the
responder rejects the PDU and the MR stays all-zero. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-thin: fix metadata refcount underflow
There's a bug in dm-thin in the function rebalance_children. If the
internal btree node has one entry, the code tries to copy all btree
entries from the node's child to the node itself and then decrement the
child's reference count.
If the child node is shared (it has reference count > 1), we won't free
it, so there would be two pointers to each of the grandchildren nodes.
But the reference counts of the grandchildren is not increased, thus the
reference count doesn't match the number of pointers that point to the
grandchildren. This results in "device mapper: space map common: unable
to decrement block" errors.
Fix this bug by incrementing reference counts on the grandchildren if the
btree node is shared. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipv6: fix NOREF dst use in seg6 and rpl lwtunnels
seg6_input_core() and rpl_input() call ip6_route_input() which sets a
NOREF dst on the skb, then pass it to dst_cache_set_ip6() invoking
dst_hold() unconditionally.
On PREEMPT_RT, ksoftirqd is preemptible and a higher-priority task can
release the underlying pcpu_rt between the lookup and the caching
through a concurrent FIB lookup on a shared nexthop.
Simplified race sequence:
ksoftirqd/X higher-prio task (same CPU X)
----------- --------------------------------
seg6_input_core(,skb)/rpl_input(skb)
dst_cache_get()
-> miss
ip6_route_input(skb)
-> ip6_pol_route(,skb,flags)
[RT6_LOOKUP_F_DST_NOREF in flags]
-> FIB lookup resolves fib6_nh
[nhid=N route]
-> rt6_make_pcpu_route()
[creates pcpu_rt, refcount=1]
pcpu_rt->sernum = fib6_sernum
[fib6_sernum=W]
-> cmpxchg(fib6_nh.rt6i_pcpu,
NULL, pcpu_rt)
[slot was empty, store succeeds]
-> skb_dst_set_noref(skb, dst)
[dst is pcpu_rt, refcount still 1]
rt_genid_bump_ipv6()
-> bumps fib6_sernum
[fib6_sernum from W to Z]
ip6_route_output()
-> ip6_pol_route()
-> FIB lookup resolves fib6_nh
[nhid=N]
-> rt6_get_pcpu_route()
pcpu_rt->sernum != fib6_sernum
[W <> Z, stale]
-> prev = xchg(rt6i_pcpu, NULL)
-> dst_release(prev)
[prev is pcpu_rt,
refcount 1->0, dead]
dst = skb_dst(skb)
[dst is the dead pcpu_rt]
dst_cache_set_ip6(dst)
-> dst_hold() on dead dst
-> WARN / use-after-free
For the race to occur, ksoftirqd must be preemptible (PREEMPT_RT without
PREEMPT_RT_NEEDS_BH_LOCK) and a concurrent task must be able to release
the pcpu_rt. Shared nexthop objects provide such a path, as two routes
pointing to the same nhid share the same fib6_nh and its rt6i_pcpu
entry.
Fix seg6_input_core() and rpl_input() by calling skb_dst_force() after
ip6_route_input() to force the NOREF dst into a refcounted one before
caching.
The output path is not affected as ip6_route_output() already returns a
refcounted dst. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nSVM: Raise #UD if unhandled VMMCALL isn't intercepted by L1
Explicitly synthesize a #UD for VMMCALL if L2 is active, L1 does NOT want
to intercept VMMCALL, nested_svm_l2_tlb_flush_enabled() is true, and the
hypercall is something other than one of the supported Hyper-V hypercalls.
When all of the above conditions are met, KVM will intercept VMMCALL but
never forward it to L1, i.e. will let L2 make hypercalls as if it were L1.
The TLFS says a whole lot of nothing about this scenario, so go with the
architectural behavior, which says that VMMCALL #UDs if it's not
intercepted.
Opportunistically do a 2-for-1 stub trade by stub-ifying the new API
instead of the helpers it uses. The last remaining "single" stub will
soon be dropped as well.
[sean: rewrite changelog and comment, tag for stable, remove defunct stubs] |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5: validate payload size before accessing journal metadata
r5c_recovery_analyze_meta_block() and
r5l_recovery_verify_data_checksum_for_mb() iterate over payloads in a
journal metadata block using on-disk payload size fields without
validating them against the remaining space in the metadata block.
A corrupted journal contains payload sizes extending beyond the PAGE_SIZE
boundary can cause out-of-bounds reads when accessing payload fields or
computing offsets.
Add bounds validation for each payload type to ensure the full payload
fits within meta_size before processing. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: defio: Disconnect deferred I/O from the lifetime of struct fb_info
Hold state of deferred I/O in struct fb_deferred_io_state. Allocate an
instance as part of initializing deferred I/O and remove it only after
the final mapping has been closed. If the fb_info and the contained
deferred I/O meanwhile goes away, clear struct fb_deferred_io_state.info
to invalidate the mapping. Any access will then result in a SIGBUS
signal.
Fixes a long-standing problem, where a device hot-unplug happens while
user space still has an active mapping of the graphics memory. The hot-
unplug frees the instance of struct fb_info. Accessing the memory will
operate on undefined state. |
| In the Linux kernel, the following vulnerability has been resolved:
selinux: fix overlayfs mmap() and mprotect() access checks
The existing SELinux security model for overlayfs is to allow access if
the current task is able to access the top level file (the "user" file)
and the mounter's credentials are sufficient to access the lower
level file (the "backing" file). Unfortunately, the current code does
not properly enforce these access controls for both mmap() and mprotect()
operations on overlayfs filesystems.
This patch makes use of the newly created security_mmap_backing_file()
LSM hook to provide the missing backing file enforcement for mmap()
operations, and leverages the backing file API and new LSM blob to
provide the necessary information to properly enforce the mprotect()
access controls. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: only d_add() negative dentries when they are unhashed
Ceph can call d_add(dentry, NULL) on a negative dentry that is already
present in the primary dcache hash.
In the current VFS that is not safe. d_add() goes through __d_add()
to __d_rehash(), which unconditionally reinserts dentry->d_hash into
the hlist_bl bucket. If the dentry is already hashed, reinserting the
same node can corrupt the bucket, including creating a self-loop.
Once that happens, __d_lookup() can spin forever in the hlist_bl walk,
typically looping only on the d_name.hash mismatch check and
eventually triggering RCU stall reports like this one:
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 87-....: (2100 ticks this GP) idle=3a4c/1/0x4000000000000000 softirq=25003319/25003319 fqs=829
rcu: (t=2101 jiffies g=79058445 q=698988 ncpus=192)
CPU: 87 UID: 2952868916 PID: 3933303 Comm: php-cgi8.3 Not tainted 6.18.17-i1-amd #950 NONE
Hardware name: Dell Inc. PowerEdge R7615/0G9DHV, BIOS 1.6.6 09/22/2023
RIP: 0010:__d_lookup+0x46/0xb0
Code: c1 e8 07 48 8d 04 c2 48 8b 00 49 89 fc 49 89 f5 48 89 c3 48 83 e3 fe 48 83 f8 01 77 0f eb 2d 0f 1f 44 00 00 48 8b 1b 48 85 db <74> 20 39 6b 18 75 f3 48 8d 7b 78 e8 ba 85 d0 00 4c 39 63 10 74 1f
RSP: 0018:ff745a70c8253898 EFLAGS: 00000282
RAX: ff26e470054cb208 RBX: ff26e470054cb208 RCX: 000000006e958966
RDX: ff26e48267340000 RSI: ff745a70c82539b0 RDI: ff26e458f74655c0
RBP: 000000006e958966 R08: 0000000000000180 R09: 9cd08d909b919a89
R10: ff26e458f74655c0 R11: 0000000000000000 R12: ff26e458f74655c0
R13: ff745a70c82539b0 R14: d0d0d0d0d0d0d0d0 R15: 2f2f2f2f2f2f2f2f
FS: 00007f5770896980(0000) GS:ff26e482c5d88000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f5764de50c0 CR3: 000000a72abb5001 CR4: 0000000000771ef0
PKRU: 55555554
Call Trace:
<TASK>
lookup_fast+0x9f/0x100
walk_component+0x1f/0x150
link_path_walk+0x20e/0x3d0
path_lookupat+0x68/0x180
filename_lookup+0xdc/0x1e0
vfs_statx+0x6c/0x140
vfs_fstatat+0x67/0xa0
__do_sys_newfstatat+0x24/0x60
do_syscall_64+0x6a/0x230
entry_SYSCALL_64_after_hwframe+0x76/0x7e
This is reachable with reused cached negative dentries. A Ceph lookup
or atomic_open can be handed a negative dentry that is already hashed,
and fs/ceph/dir.c then hits one of two paths that incorrectly assume
"negative" also means "unhashed":
- ceph_finish_lookup():
MDS reply is -ENOENT with no trace
-> d_add(dentry, NULL)
- ceph_lookup():
local ENOENT fast path for a complete directory with shared caps
-> d_add(dentry, NULL)
Both paths can therefore re-add an already-hashed negative dentry.
Ceph already uses the correct pattern elsewhere: ceph_fill_trace() only
calls d_add(dn, NULL) for a negative null-dentry reply when d_unhashed(dn)
is true.
Fix both fs/ceph/dir.c sites the same way: only call d_add() for a
negative dentry when it is actually unhashed. If the negative dentry
is already hashed, leave it in place and reuse it as-is.
This preserves the existing behavior for unhashed dentries while
avoiding d_hash list corruption for reused hashed negatives. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Validate pad and ICRC before payload_size() in rxe_rcv
rxe_rcv() currently checks only that the incoming packet is at least
header_size(pkt) bytes long before payload_size() is used.
However, payload_size() subtracts both the attacker-controlled BTH pad
field and RXE_ICRC_SIZE from pkt->paylen:
payload_size = pkt->paylen - offset[RXE_PAYLOAD] - bth_pad(pkt)
- RXE_ICRC_SIZE
This means a short packet can still make payload_size() underflow even
if it includes enough bytes for the fixed headers. Simply requiring
header_size(pkt) + RXE_ICRC_SIZE is not sufficient either, because a
packet with a forged non-zero BTH pad can still leave payload_size()
negative and pass an underflowed value to later receive-path users.
Fix this by validating pkt->paylen against the full minimum length
required by payload_size(): header_size(pkt) + bth_pad(pkt) +
RXE_ICRC_SIZE. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: icmp: validate reply type before using icmp_pointers
Extended echo replies use ICMP_EXT_ECHOREPLY as the outbound reply type.
That value is outside the range covered by icmp_pointers[], which only
describes the traditional ICMP types up to NR_ICMP_TYPES.
Avoid consulting icmp_pointers[] for reply types outside that range, and
use array_index_nospec() for the remaining in-range lookup. Normal ICMP
replies keep their existing behavior unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: avoid early lgr access in smc_clc_wait_msg
A CLC decline can be received while the handshake is still in an early
stage, before the connection has been associated with a link group.
The decline handling in smc_clc_wait_msg() updates link-group level sync
state for first-contact declines, but that state only exists after link
group setup has completed. Guard the link-group update accordingly and
keep the per-socket peer diagnosis handling unchanged.
This preserves the existing sync_err handling for established link-group
contexts and avoids touching link-group state before it is available. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: call sk_data_ready() after listener migration
When inet_csk_listen_stop() migrates an established child socket from
a closing listener to another socket in the same SO_REUSEPORT group,
the target listener gets a new accept-queue entry via
inet_csk_reqsk_queue_add(), but that path never notifies the target
listener's waiters. A nonblocking accept() still works because it
checks the queue directly, but poll()/epoll_wait() waiters and
blocking accept() callers can also remain asleep indefinitely.
Call READ_ONCE(nsk->sk_data_ready)(nsk) after a successful migration
in inet_csk_listen_stop().
However, after inet_csk_reqsk_queue_add() succeeds, the ref acquired
in reuseport_migrate_sock() is effectively transferred to
nreq->rsk_listener. Another CPU can then dequeue nreq via accept()
or listener shutdown, hit reqsk_put(), and drop that listener ref.
Since listeners are SOCK_RCU_FREE, wrap the post-queue_add()
dereferences of nsk in rcu_read_lock()/rcu_read_unlock(), which also
covers the existing sock_net(nsk) access in that path.
The reqsk_timer_handler() path does not need the same changes for two
reasons: half-open requests become readable only after the final ACK,
where tcp_child_process() already wakes the listener; and once nreq is
visible via inet_ehash_insert(), the success path no longer touches
nsk directly. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix re-decryption of RESPONSE packets
If a RESPONSE packet gets a temporary failure during processing, it may end
up in a partially decrypted state - and then get requeued for a retry.
Fix this by just discarding the packet; we will send another CHALLENGE
packet and thereby elicit a further response. Similarly, discard an
incoming CHALLENGE packet if we get an error whilst generating a RESPONSE;
the server will send another CHALLENGE. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Fix a crash due to incorrect cleanup usage of kfree
Annotating a local pointer variable, which will be assigned with the
kmalloc-family functions, with the `__cleanup(kfree)` attribute will
make the address of the local variable, rather than the address returned
by kmalloc, passed to kfree directly and lead to a crash due to invalid
deallocation of stack address. According to other places in the repo,
the correct usage should be `__free(kfree)`. The code coincidentally
compiled because the parameter type `void *` of kfree is compatible with
the desired type `struct { ... } **`. |
| In the Linux kernel, the following vulnerability has been resolved:
md/md-llbitmap: fix percpu_ref not resurrected on suspend timeout
When llbitmap_suspend_timeout() times out waiting for percpu_ref to
become zero, it returns -ETIMEDOUT without resurrecting the percpu_ref.
The caller (md_llbitmap_daemon_fn) then continues to the next page
without calling llbitmap_resume(), leaving the percpu_ref in a killed
state permanently.
Fix this by resurrecting the percpu_ref before returning the error,
ensuring the page control structure remains usable for subsequent
operations. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down context entry
When tearing down a context entry, the current implementation zeros the
entire 128-bit entry using multiple 64-bit writes. This creates a window
where the hardware can fetch a "torn" entry — where some fields are
already zeroed while the 'Present' bit is still set — leading to
unpredictable behavior or spurious faults.
While x86 provides strong write ordering, the compiler may reorder writes
to the two 64-bit halves of the context entry. Even without compiler
reordering, the hardware fetch is not guaranteed to be atomic with
respect to multiple CPU writes.
Align with the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the context entry first to
signal the transition of ownership from hardware to software.
2. Use dma_wmb() to ensure the cleared bit is visible to the IOMMU.
3. Perform the required cache and context-cache invalidation to ensure
hardware no longer has cached references to the entry.
4. Fully zero out the entry only after the invalidation is complete.
Also, add a dma_wmb() to context_set_present() to ensure the entry
is fully initialized before the 'Present' bit becomes visible. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Preserve id of register in sync_linked_regs()
sync_linked_regs() copies the id of known_reg to reg when propagating
bounds of known_reg to reg using the off of known_reg, but when
known_reg was linked to reg like:
known_reg = reg ; both known_reg and reg get same id
known_reg += 4 ; known_reg gets off = 4, and its id gets BPF_ADD_CONST
now when a call to sync_linked_regs() happens, let's say with the following:
if known_reg >= 10 goto pc+2
known_reg's new bounds are propagated to reg but now reg gets
BPF_ADD_CONST from the copy.
This means if another link to reg is created like:
another_reg = reg ; another_reg should get the id of reg but
assign_scalar_id_before_mov() sees
BPF_ADD_CONST on reg and assigns a new id to it.
As reg has a new id now, known_reg's link to reg is broken. If we find
new bounds for known_reg, they will not be propagated to reg.
This can be seen in the selftest added in the next commit:
0: (85) call bpf_get_prandom_u32#7 ; R0=scalar()
1: (57) r0 &= 255 ; R0=scalar(smin=smin32=0,smax=umax=smax32=umax32=255,var_off=(0x0; 0xff))
2: (bf) r1 = r0 ; R0=scalar(id=1,smin=smin32=0,smax=umax=smax32=umax32=255,var_off=(0x0; 0xff)) R1=scalar(id=1,smin=smin32=0,smax=umax=smax32=umax32=255,var_off=(0x0; 0xff))
3: (07) r1 += 4 ; R1=scalar(id=1+4,smin=umin=smin32=umin32=4,smax=umax=smax32=umax32=259,var_off=(0x0; 0x1ff))
4: (a5) if r1 < 0xa goto pc+4 ; R1=scalar(id=1+4,smin=umin=smin32=umin32=10,smax=umax=smax32=umax32=259,var_off=(0x0; 0x1ff))
5: (bf) r2 = r0 ; R0=scalar(id=2,smin=umin=smin32=umin32=6,smax=umax=smax32=umax32=255) R2=scalar(id=2,smin=umin=smin32=umin32=6,smax=umax=smax32=umax32=255)
6: (a5) if r1 < 0xe goto pc+2 ; R1=scalar(id=1+4,smin=umin=smin32=umin32=14,smax=umax=smax32=umax32=259,var_off=(0x0; 0x1ff))
7: (35) if r0 >= 0xa goto pc+1 ; R0=scalar(id=2,smin=umin=smin32=umin32=6,smax=umax=smax32=umax32=9,var_off=(0x0; 0xf))
8: (37) r0 /= 0
div by zero
When 4 is verified, r1's bounds are propagated to r0 but r0 also gets
BPF_ADD_CONST (bug).
When 5 is verified, r0 gets a new id (2) and its link with r1 is broken.
After 6 we know r1 has bounds [14, 259] and therefore r0 should have
bounds [10, 255], therefore the branch at 7 is always taken. But because
r0's id was changed to 2, r1's new bounds are not propagated to r0.
The verifier still thinks r0 has bounds [6, 255] before 7 and execution
can reach div by zero.
Fix this by preserving id in sync_linked_regs() like off and subreg_def. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down PASID entry
The Intel VT-d Scalable Mode PASID table entry consists of 512 bits (64
bytes). When tearing down an entry, the current implementation zeros the
entire 64-byte structure immediately using multiple 64-bit writes.
Since the IOMMU hardware may fetch these 64 bytes using multiple
internal transactions (e.g., four 128-bit bursts), updating or zeroing
the entire entry while it is active (P=1) risks a "torn" read. If a
hardware fetch occurs simultaneously with the CPU zeroing the entry, the
hardware could observe an inconsistent state, leading to unpredictable
behavior or spurious faults.
Follow the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the PASID entry.
2. Use a dma_wmb() to ensure the cleared bit is visible to hardware
before proceeding.
3. Execute the required invalidation sequence (PASID cache, IOTLB, and
Device-TLB flush) to ensure the hardware has released all cached
references.
4. Only after the flushes are complete, zero out the remaining fields
of the PASID entry.
Also, add a dma_wmb() in pasid_set_present() to ensure that all other
fields of the PASID entry are visible to the hardware before the Present
bit is set. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix watch_id bounds checking in debug address watch v2
The address watch clear code receives watch_id as an unsigned value
(u32), but some helper functions were using a signed int and checked
bits by shifting with watch_id.
If a very large watch_id is passed from userspace, it can be converted
to a negative value. This can cause invalid shifts and may access
memory outside the watch_points array.
drm/amdkfd: Fix watch_id bounds checking in debug address watch v2
Fix this by checking that watch_id is within MAX_WATCH_ADDRESSES before
using it. Also use BIT(watch_id) to test and clear bits safely.
This keeps the behavior unchanged for valid watch IDs and avoids
undefined behavior for invalid ones.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_debug.c:448
kfd_dbg_trap_clear_dev_address_watch() error: buffer overflow
'pdd->watch_points' 4 <= u32max user_rl='0-3,2147483648-u32max' uncapped
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_debug.c
433 int kfd_dbg_trap_clear_dev_address_watch(struct kfd_process_device *pdd,
434 uint32_t watch_id)
435 {
436 int r;
437
438 if (!kfd_dbg_owns_dev_watch_id(pdd, watch_id))
kfd_dbg_owns_dev_watch_id() doesn't check for negative values so if
watch_id is larger than INT_MAX it leads to a buffer overflow.
(Negative shifts are undefined).
439 return -EINVAL;
440
441 if (!pdd->dev->kfd->shared_resources.enable_mes) {
442 r = debug_lock_and_unmap(pdd->dev->dqm);
443 if (r)
444 return r;
445 }
446
447 amdgpu_gfx_off_ctrl(pdd->dev->adev, false);
--> 448 pdd->watch_points[watch_id] = pdd->dev->kfd2kgd->clear_address_watch(
449 pdd->dev->adev,
450 watch_id);
v2: (as per, Jonathan Kim)
- Add early watch_id >= MAX_WATCH_ADDRESSES validation in the set path to
match the clear path.
- Drop the redundant bounds check in kfd_dbg_owns_dev_watch_id(). |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Flush cache for PASID table before using it
When writing the address of a freshly allocated zero-initialized PASID
table to a PASID directory entry, do that after the CPU cache flush for
this PASID table, not before it, to avoid the time window when this
PASID table may be already used by non-coherent IOMMU hardware while
its contents in RAM is still some random old data, not zero-initialized. |
